Manual Auto Operation; Airflow Direction; Operating Tips - Fujitsu AIRSTAGE AUXV007GLEH Operation Manual
Hide thumbs
Also See for AIRSTAGE AUXV007GLEH:
- Installation manual (13 pages) ,
- Design & technical manual (1038 pages) ,
- Design & technical manual (1092 pages)
Table of Contents
Advertisement
MANUAL AUTO OPERATION
Use the MANUAL AUTO operation in the event the remote controller is
lost or otherwise unavailable.
*Limited to only when the optional IR receiver unit is connected.
CAUTION
Do not press the MANUAL AUTO button with wet hands or pointed ob-
jects, otherwise an electric shock or malfunction may occur.
Starting Operation
Press the MANUAL AUTO button on the operating
control panel.
The operation can be set in the following setting.
Operating mode
AUTO:
When Auto mode cannot be selected, it will
operate in the same mode as the other indoor
unit in the same system. (When other indoor
unit in the same system doesn't operate, the air
conditioner will operate in cooling.)
Fan speed
AUTO
Setting temperature
23 °C
Stopping Operation
Press the MANUAL AUTO button on the operating
control panel.
AIRFLOW DIRECTION
Vertical airfl ow direction
The up/down airfl ow direction can be controlled with the remote control-
ler.
The position of the wind direction that can be set varies depending on the
remote controller type.
By the Wired remote controller
(1)
(2)
(3)
(4)
By the Wireless remote controller*
*Limited to only when the optional IR receiver unit is connected.
(1)
(2)
(3)
(4)
(5)
NOTE:
The airfl ow setting from the wireless remote controller will not be re-
fl ected in the display of the wired remote controller or the mobile app.
Cooling & Dry:
(1), (2), (3), (4)
Heating:
(1), (2), (3), (4)
Cooling & Dry:
(1), (2), (3), (4), (5)
Heating:
(1), (2), (3), (4), (5)
Swing
The swinging up/down airfl ow direction can be set.
OPERATING TIPS
Operation and Performance
About priority state and standby state
● Multiple indoor units can be connected within the same system. De-
pending on the system, choice of operating mode are limited.
Cooling priority state:
When the other indoor units within the same system operate in cooling
or dry mode, heating cannot be selected at the same time.
Heating priority state:
When the other indoor units within the same system operate in heating
mode, cooling and dry mode cannot be selected at the same time.
Standby state:
The standby state activates when 2 or more indoor units start up at the
same time in diff erent mode. Any indoor unit other than priority mode
will wait in standby state until priority mode changes (operation starts
as soon as priority is switched).
At this time, the OPERATION indicator lamp (green) lights up and the
TIMER indicator lamp (orange) blinks (limited to only when the optional
IR receiver unit is connected).
Low ambient cooling
● When the outdoor temperature drops, the outdoor unit's fans may
switch to Low Speed, or one of the fans may stop intermittently.
Heating performance
● Heating mode operates on the heat-pump principle, absorbing heat
from outdoor air and transferring that heat indoors. As a result, the
operating performance is reduced as outdoor air temperature drops.
If you feel that insuffi cient heating performance is being produced, we
recommend you use this air conditioner in conjunction with another
type of heating appliance.
● Heating mode heat your entire room by recirculating air throughout the
room, with the result that some time may be required after fi rst starting
the air conditioner until the room is heated.
Automatic defrosting
● When using the Heating mode under conditions of low outdoor air
temperature high humidity, frost may form on the outdoor unit, resulting
in reduced operating performance. In order to prevent this kind of re-
duced performance, this unit is equipped with an Automatic defrosting
function. If frost forms, the air conditioner will temporarily stop, and the
defrosting circuit will operate briefl y (for about 4 to 15 minutes).
During Automatic Defrosting operation, the OPERATION indicator
lamp (green) will blinks (limited to only when the optional IR receiver
unit is connected).
Oil recovery operation
● Periodically, the Oil recovery operation is performed in order to return
compressor oil to the outdoor unit.
During Oil recovery operation, the OPERATION indicator lamp (green)
will blinks (for about 10 minutes) (limited to only when the optional IR
receiver unit is connected).
En-2
Advertisement
Table of Contents
