Operating instructions for dishwashers To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions as well as the installation plan before it is in‐ stalled and used for the first time. en-AU, NZ HG05 M.-Nr.
Contents Guide to the appliance................... 5 Appliance overview....................5 Control panel......................6 Warning and Safety instructions ................7 Caring for the environment ................. 16 Disposal of the packing material................16 Disposing of your old appliance ................16 Energy-saving dishwashing ................... 17 Before using for the first time................
Page 3
Contents Switching on ......................49 Selecting a programme..................49 Starting the programme ..................50 Display ........................50 Energy management ....................51 At the end of the programme................. 51 Switching off ......................52 Unloading the dishwasher ..................52 Interrupting a programme ..................53 Changing a programme ..................
Page 4
Contents After sales service ....................82 Repairs ........................82 Warranty......................... 82 Optional accessories ................... 83 Electrical connection ................... 85 Water connection....................86 The Miele Waterproof system ................86 Connection to the water supply................86 Drainage......................... 87 Technical data ...................... 88...
Guide to the appliance Appliance overview a Upper spray arm (not visible) g Filter combination b Cutlery tray (depending on model) h Data plate c Upper basket i In-operation indicator light d Middle spray arm j Rinse aid reservoir e Air inlet for drying (depending on k Dual compartment detergent dis‐...
Guide to the appliance Control panel a In-operation indicator light e Delay start button with indicator light b Programme selection f Short button with indicator light c Display g Programme selector button d Check/Refill indicators h On/Off button These operating instructions apply to several different dishwasher models with different heights.
Keep the installation plan and the operating instructions in a safe place and pass them on to any future owner. Miele cannot be held liable for damage caused by non-compli‐ ance with this information.
Page 8
Warning and Safety instructions Correct application This appliance is designed for domestic use and for use in similar environments by guests in hotel or motel rooms, bed & breakfasts and other typical living quarters. This does not include common/ shared facilities or commercial facilities within hotels, motels or bed &...
Page 9
Warning and Safety instructions Safety with children Young children must not be allowed to use this appliance. Older children may only use the appliance when its operation has been clearly explained to them and they are able to use it safely, rec‐ ognising the dangers of misuse.
Page 10
Repairs and other work by unqualified persons could be danger‐ ous. Installation, maintenance work and repairs to electrical applian‐ ces must only be carried out by a Miele approved service technician. Before installation, check the dishwasher for visible signs of dam‐...
Page 11
The water pressure (flow pressure at the connection point) must be between 30 and 1000 kPa (0.3 and 10 bar). A damaged appliance could be dangerous. If the dishwasher gets damaged, switch it off at the mains and call Miele.
Page 12
If the connection cable is damaged, it must be replaced with a special cable of the same type (available from Miele) by a Miele au‐ thorised service technician only. In areas which may be subject to infestation by cockroaches or other vermin, pay particular attention to keeping the appliance and its surroundings in a clean condition at all times.
Page 13
Warning and Safety instructions If you want to convert your freestanding dishwasher to a built-un‐ der ("U") model, you will need to order the appropriate conversion kit. If you remove the existing plinth, you must replace it with a U- model plinth.
Warning and Safety instructions Correct use Do not use solvents in the dishwasher. Danger of explosion! Do not inhale or ingest dishwasher detergent. Dishwasher deter‐ gents contain irritants or corrosive ingredients which can cause burning in the nose, mouth and throat if swallowed, or inhibit breath‐ ing.
Page 15
Accessories Use only genuine original Miele spare parts. If spare parts or ac‐ cessories from other manufacturers are used, the warranty will be in‐ validated, and Miele cannot accept liability. Disposal of your old dishwasher ...
Caring for the environment Disposal of the packing mate‐ Disposing of your old appli‐ rial ance The packaging is designed to protect Electrical and electronic appliances of‐ the appliance from damage during ten contain materials which, if handled transportation. The packaging materials or disposed of incorrectly, could be po‐...
If the water is heated by solar panels, for example, this would be energy efficient. However, if your water is heated by electricity, we would recommend connection to cold water. You can find further tips on energy- saving dishwashing in "Miele's guide to dishwashing".
Before using for the first time Opening the door Closing the door Push the baskets right in. Then lift the door upwards and push until it clicks into position. Danger of injury! Do not put your hand inside the door as it is closing.
Before using for the first time Water softener Enter the water hardness below: ____________mmol/l or °d In order to achieve good cleaning re‐ sults, the dishwasher needs to operate The dishwasher is programmed at the with soft water. Hard water results in a factory for a water hardness level of 2.7 build-up of calcium deposits on crock‐...
Before using for the first time Displaying and setting the water Press the button twice. hardness The indicator will flash rapidly twice Open the door. at intervals. Switch the dishwasher off with the The value set for the water hardness is button, if it is switched on.
Page 21
Before using for the first time °d mmol/l °f Display °d mmol/l °f Display 37-45 6.6-8,0 66-80 46-60 8.2-10,7 82-107 61-70 10.9-12,5 109-125...
Before using for the first time Before using the appliance for If the water hardness in your area is the first time, you require: constantly lower than 0.9 mmol/l (5 °d), you do not need to add dish‐ – approx. 2 litres of water, washer salt.
Before using for the first time Filling the salt reservoir Before filling the salt reservoir with dishwasher salt for the first time, you must fill it with approx. 2 litres of wa‐ ter to enable the salt to dissolve. Once the dishwasher has been used, there is always sufficient water in the reservoir.
Before using for the first time Salt indicator If you only ever use multi-function combination products in your dish‐ Fill the salt reservoir with dishwasher washer, you can switch off both refill salt when the Salt indicator light reminders for salt and rinse aid if you comes on (If it comes on during a wish (see "Programme options - programme, wait until the end of the...
Before using for the first time Rinse aid If you only ever use combination products containing rinse aid in your Rinse aid is necessary to ensure water dishwasher, you do not need to add does not cling and leave marks on rinse aid.
Before using for the first time Rinse aid indicator When the Rinse aid indicator light comes on, the reservoir contains suffi‐ cient rinse aid for 2 - 3 programmes on‐ Add rinse aid in plenty of time. If you only ever use multi-function combination products in your dish‐...
Before using for the first time Setting the rinse aid dosage Switch the dishwasher off with the button, if it is switched on. You can adjust the rinse aid dosage for best results. Press the programme selector button ...
Loading the dishwasher Notes – The spray arms must not be blocked by items which are too tall or hang Remove coarse food residues from through the baskets. If in doubt, test crockery. for free movement by manually rotat‐ ing the spray arms. There is no need to rinse items under running water.
Page 29
– Use detergents with glass protective ted at the end of a programme, where additives (e.g. Miele CareCollection water has not run off smoothly. It may tabs). need to be rubbed dry with a soft cloth.
Loading the dishwasher Upper basket Cup rack To make room for tall items, raise the See "Loading the dishwasher / Load‐ rack upwards. ing examples" for examples of how to Glasses can be arranged along the po‐ load crockery and cutlery. sitioning rail of the cup rack to give them some support during the pro‐...
Loading the dishwasher Adjusting the upper basket Depending on the setting of the upper basket, the following plate dimensions In order to gain more space for taller can be accommodated. pieces of crockery in the bottom or up‐ per basket, the upper basket can be Dishwashers with cutlery basket adjusted on three levels with 2 cm be‐...
Loading the dishwasher Lower basket MultiComfort area The rear section of the lower basket is See "Loading the dishwasher / Load‐ used for washing cups, glasses, plates, ing examples" for examples of how to pots and pans. load crockery and cutlery. ...
Page 33
Loading the dishwasher Hinged spikes (depending on model) The spikes at the front are used for washing plates, soup bowls, platters, dessert bowls and saucers. Both rows of spikes can be lowered to make more room for large items, e.g. pots, pans and dishes.
Loading the dishwasher Cutlery 3D cutlery tray (depending on model) See "Loading the dishwasher / Load‐ ing examples" for examples of how to load crockery and cutlery. Arrange the cutlery in the tray as shown. To make unloading much easier, cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc.
Loading the dishwasher Cutlery basket (depending on model) Fit it onto the cutlery basket if re‐ quired. The cutlery basket can be placed any‐ where on the front rows of spikes in the lower basket. To avoid the risk of injury, knives and forks should be placed with the han‐...
Comparison tests Test standard: AS/NZS 2007.1:2005, AS/NZS 2007.2:2005; AS/NZS 6400:2005 Standard programme for en‐ ergy label comparison tests: Capacity: 14 place settings Detergent quantity: 32.5 g in compartment II Rinse aid dispensing: Setting 3 You can find information on adjusting the rinse aid dosage in the "Rinse aid" section of this booklet.
Page 43
Comparison tests Test standard: AS/NZS 2007.1:2005, AS/NZS 2007.2:2005; AS/NZS 6400:2005 Standard programme for en‐ ergy label comparison tests: Capacity: 15 place settings Detergent quantity: 33.7 g in compartment II Rinse aid dispensing: Setting 3 You can find information on adjusting the rinse aid dosage in the "Rinse aid" section of this booklet.
For optimum cleaning and drying re‐ remove coloured stains (e.g. tea, cof‐ sults, use Miele dishwasher detergent fee, tomato sauce). and add Miele salt and Miele rinse aid separately. See "Optional accesso‐ Most dishwasher detergents are mildly ries". alkaline and contain enzymes and oxy‐...
Page 47
Operation Detergent dosage Dishwasher detergents contain Follow the dosage recommended by irritant or corrosive ingredients which the manufacturer on the packaging. can cause burning in the nose, mouth and throat if swallowed, or in‐ Unless directed otherwise, use one hibit breathing.
Operation Adding detergent Add the required amount of detergent and close the flap. Press the opening catch on the de‐ tergent dispenser. The flap will spring Make sure that the detergent packag‐ open. ing is properly closed after use to avoid it getting damp and becoming The flap is always open at the end of a lumpy.
Operation Switching on Selecting a programme Turn on the tap if it is turned off. Choose your programme according to the type of load and how dirty it is. Open the door. The different programmes and their Make sure the spray arms are not ob‐ uses are described in the Programme structed.
Operation Starting the programme Display Start the programme by closing the The duration of the programme selec‐ door. ted appears in hours and minutes in the display before the programme begins. The programme will begin. During the programme the time left until The In-operation indicator comes on to the end of the programme is displayed.
Operation Energy management At the end of the programme To save energy, the dishwasher will At the end of a programme, the In-op‐ switch off automatically 10 minutes af‐ eration indicator light will be visible ter the last time a button has been flashing slowly with the door shut.
Operation Switching off Unloading the dishwasher At the end of a programme: Dishes tend to break and chip more easily when they are hot. Allow the Open the door. dishes to cool until they are comforta‐ The dishwasher can be switched off ble enough to handle before unloading at any time using the ...
Operation Interrupting a programme Changing a programme A programme is interrupted as soon as If the detergent dispenser flap has the door is opened. already opened, do not change the If the door is closed again, the pro‐ programme. gramme will continue from the point it was at before the door was opened.
Programme options Short DetergentAgent For optimum cleaning results, the dish‐ The Short option reduces the dura‐ washer automatically adjusts the pro‐ tion of programmes in which this option gramme sequence to the type of deter‐ is available. gent being used. Depending on the In order to achieve optimum cleaning programme, this can mean that the run‐...
Programme options Switching off the refill indica‐ Press the button nine times. tors The indicator light will flash rapidly nine times at intervals. If you only ever use multi-function com‐ bination products in your dishwasher, The flashing sequence in the display you can switch the refill reminders for will show whether the refill indicators salt and rinse aid off if you wish.
Programme options Delay start Open the door. Switch the dishwasher on with the You can set the start time for a pro‐ gramme, e.g. to take advantage of night button. time electricity tariffs. The start time Select the programme you want. can be delayed between 30 minutes and 24 hours.
Page 57
Programme options Open the door if you need to check Starting a programme before the De‐ lay start period has elapsed: how long the delay period has left to run. A programme can be started before the Delay start period has elapsed. The time up until the programme starts Proceed as follows: will show counting down in the display...
Programme options Buzzer tones Press the button four times. A sequence of audible tones will sound The indicator will flash rapidly four at the end of the programme or if there times at intervals. is a fault. The flashing sequence in the display The buzzer at the end of a programme shows whether the buzzer at the end of...
Programme options Adjust Sensor wash Press the button five times. You can adjust the Sensor wash pro‐ The indicator light will flash rapidly gramme so that it will remove stubborn five times at intervals soiling in a lightly soiled load. The flashing sequence in the display in‐...
Programme options Optimise standby Press the button eight times. "Optimise standby" is activated by de‐ The indicator light will flash rapidly fault. eight times at intervals. To save energy, the dishwasher will The flashing sequence in the display switch off automatically a few minutes shows whether Optimise standby is ac‐...
Programme options Factory default settings Press the programme selector button 19 times briefly. If you have altered any settings from The indicator light will give one long the factory default, you can reset them back to the factory default settings as flash and nine brief flashes at intervals.
Programme chart Programme Programme sequence Pre-wash Main wash Interim rinse Final rinse Drying °C °C Sensor wash Variable programme sequence, sensor-controlled adjustment according to amount of crockery and soiling 47-55 required required Light soiling 55°C Intensive 75°C Sensor wash gentle Quick wash 40°C This programme is the most efficient in terms of its combined energy and water con‐...
Page 63
Programme chart Consumption Duration Electricity Water Cold water Hot water Litres Cold water Hot water h:min h:min 2:41 2:34 0.73 / 0.76 0.40 / 0.44 11.3 / 11.0 1:30-2:50 1:25-2:40 0.85 -1.35 0.65 -0.90 -16.0 1.25 0.85 14.0 2:03 1:51 1.60 1.10 15.0...
Page 64
Programme chart Crockery Food deposits Action required Variable, sensor-controlled Mixed, All fresh to dried-on programme sequence everyday crockery food deposits Shorter duration This needs a short programme Heat-sensitive glasses and plastic Shorter duration Fresh, easily removed food deposits This needs a gentle programme with glass care Shorter duration Mixed crockery...
Page 65
Programme chart Programme Detergent Compartment I Compartment II 25 ml Sensor wash 1 tab +short 20 ml Quick wash 40 °C 1 tab +short 20 ml Sensor wash gentle 1 tab +short 25 ml 1 tab 25 ml Light soiling 55 °C 1 tab +short 25 ml...
The control panel should only be wi‐ grease deposits in the cabinet, these ped with a damp cloth. can be removed with the Original Miele Cleaning the reflector panel dishwasher conditioning agent (availa‐ ble from Miele or at www.miele- The reflector panel for the In-operation shop.com, depending on country).
– dishwasher cleaner, For cleaning, you can also use a clean, damp microfibre cloth, such as – oven cleaner, the Original Miele all purpose microfi‐ – glass cleaning agents, bre cloth, without any cleaning agent. – hard, abrasive brushes or sponges, e.g.
Cleaning and care Checking the filters in the Cleaning the filters wash cabinet Switch the dishwasher off. The filter combination in the base of the wash cabinet retains coarse soil from the suds solution, preventing it access‐ ing the circulation system and re-enter‐ ing the cabinet through the spray arms.
Page 69
Cleaning and care To clean the inside of the filter, the flap Replace the filter combination so that must be opened: it lies flat in the base of the wash cabinet. Press the catches together in the direction of the arrows as shown, and ...
Cleaning and care Cleaning the spray arms Particles of food can get stuck in the spray arm jets and bearings. The spray arms should therefore be inspected and cleaned regularly (approx. every 4 - 6 months). Switch the dishwasher off. Remove the spray arms as follows: ...
Reset or replace the fuse (see data plate for mini‐ mum fuse rating). If the mains fuse trips again, call Miele. After the programme The reflector panel was not correctly fitted. has started, the In-op‐...
Page 72
Close the door. Fault code appears If the indicator lights flash again, there is a technical in the display. fault. Call Miele. Fault : The Waterproof system has reacted. The buzzer is sounding Turn off the tap.
Problem solving guide Water inlet fault Problem Possible cause and remedy The In-operation indica‐ The tap is turned off. tor is flashing quickly. Turn on the tap fully. The buzzer is sounding. The Inlet/Drain indica‐ tor is flashing on and off.
Problem solving guide Water drainage fault Problem Possible cause and remedy The In-operation indica‐ Before rectifying the problem, you must: tor is flashing quickly. Switch the dishwasher off with the button. The buzzer is sounding. The water outlet is restricted. The Inlet/Drain indica‐...
Problem solving guide General problems Problem Possible cause and remedy Detergent residue is left The dispenser was still damp when detergent was in the dispenser at the added. end of a programme. Make sure the dispenser is dry before adding de‐ tergent.
Problem solving guide Noises Problem Possible cause and remedy Knocking noise in the A spray arm is knocking against an item in a basket. wash cabinet. Interrupt the programme, and rearrange the items which are obstructing the spray arm. Rattling noise in the Items of crockery are insecure in the wash cabinet.
Problem solving guide Unsatisfactory washing result Problem Possible cause and remedy The dishes are not The dishes were not loaded correctly. clean. See notes in "Loading the dishwasher". The programme was not powerful enough. Select a more intensive programme (see "Pro‐ gramme chart").
Page 78
Problem solving guide Problem Possible cause and remedy Dishes, cutlery and The amount of rinse aid may be insufficient, or the glasses are not dry or rinse aid reservoir is empty. are flecked. Replenish the reservoir, increase the dosage or change the brand of rinse aid (see "Before using for the first time - Rinse aid").
Page 79
Problem solving guide Problem Possible cause and remedy White residue is visible Not enough rinse aid was used. on cutlery and crock‐ Increase the dosage (see "Before using for the first ery, clouding occurs on time - Rinse aid"). glassware;...
This Replace the filter and washer, making filter is available from Miele. sure they are sitting correctly. Reconnect the inlet hose to the tap, Cleaning the filter: making sure it goes on correctly and ...
Maintenance Cleaning the drain pump and non-return valve If the water has not been pumped away at the end of a programme, the drain pump or the non-return valve might be blocked. They are, however, easy to clean. Disconnect the dishwasher from the mains supply.
For further information, please refer to – Miele your warranty booklet. The contact details for Miele are giv‐ en at the back of these instructions. When contacting Miele, please quote the model and serial number of your dishwasher, both of which are shown on the data plate on the right-hand side of the door.
– phosphate-free - safe for the environ‐ www.miele-shop.com (depending on ment country) or from Miele (see end of this booklet for contact details). – water-soluble wrapping - no need to unwrap Powder detergent –...
Page 84
Optional accessories Dishwasher care products Glass rail This rail is designed to hold glasses Miele cleaning and care products pro‐ with stems securely in the lower basket. vide optimum care for your dishwasher. Dishwasher cleaner – cleans the dishwasher effectively and thoroughly –...
(e.g. danger of overheating). safety regulations. If the connection cable is damaged, it must be replaced with a Miele cable of the same type by a Miele approved service technician only. Do not connect the appliance to an in‐...
As long as your dishwasher has been 30 and 1000 kPa (0.3 and 10 bar). If installed correctly, the Miele waterproof the water pressure is too high, a anti-leak system will protect you from pressure reducer valve must be fit‐...
Water connection Drainage Venting the drainage system If the on-site drain connection is situ‐ – The appliance drainage system is fit‐ ated lower than the guide path for the ted with a non-return valve which bottom basket rollers in the open door, prevents dirty water from flowing the drainage system must be vented.
Technical data Dishwasher model Standard Height 80.5 cm (adjustable + 84.5 cm (adjustable + 6.5 cm) 6.5 cm) Height of building-in recess Min. 80.5 cm (+ 6.5 Min. 84.5 cm (+ 6.5 Width 59.8 cm 59.8 cm Width of building-in recess 60 cm 60 cm Depth...
Page 92
G 6160 / G 6165 en-AU, NZ M.-Nr. 09 867 830 / 01...