SAFETY PRECAUTIONS IMPORTANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this service unit under test. manual and its supplements and addenda, read and follow the 2. After removing an electrical assembly equipped with ES SAFETY PRECAUTIONS on page 3 of this publication. devices, place the assembly on a conductive surface such as NOTE: If unforeseen circumstances create conflict between the aluminum foil, to prevent electrostatic charge buildup or...
Page 5
IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through Circuit Board Foil Repair which the IC leads are inserted and then bent flat against the Excessive heat applied to the copper foil of any printed circuit circuit foil. When holes are the slotted type, the following technique board will weaken the adhesive that bonds the foil to the circuit should be used to remove and replace the IC.
SPECIFICATION NOTE : Specifications and others are subject to change without notice for improvement. 1. Application range This specification is applied to ML-042A chassis. 2. Requirement for Test Testing for standard of each part must be followed in below condition. (1) Temperature: 25°C ±...
Page 7
5. Engineering Specification Item Content Remark Response Time Rise Time (typ) : 5ms TX LED Power LED Blue LED POWER off mode (No adapter) POWER off mode Amber (adapter) POWER on mode Green (network disconnected) POWER on mode Green Blue (network connected) RX battery LED Battery...
Page 8
6. Optical Character Item Criteria Remark Viewing Angle Horizontal(R/L) : 65¡£ / 65¡£ (Typ.) (R¡ˆ10) Vertical(Top/Bottom) : 45¡£ / 55¡£ (Typ.) Luminance Average Luminance (cd/m2) 450(typ) Luminance Uniformity(%) Contrast Ratio 400(normal) CIE Color Coordinates Min. Normal Max. White 0.286 0.289 0.292 0.301 0.304...
DISASSEMBLY - Remove screws attached to stand by coin or (-) driver. - Remove the battery. - Disassembly Stand from Set. - Disassembly Back cover after press the battery as pull the - Remove Speaker's screws of both sides. edge of Back cover by hand as the picture. AL Tape AL Tape - Remove the POWER PCB screw.
Page 10
DISASSEMBLY - Remove screws in stand. - Push the cover to arrow direction. - Lift cover. - Remove screws. Al tape - Remove antenna and AL Tape as the picture. - Remove screws of Rear shield. - Lift Rear shield as the picture. - 10 -...
SERVICE TEST PROGRAM (2) LED Test 1. Test Items - LED Operation Test of Rx (MICOM : 1.3.0, ROMFS : 1.2 12/21 ENG), TX SSID : 80035E (Rx Micom/Rx Flash/ Version Display), TX SSID display Test Items - LED : Rx LED Operation Test (MICOM : 1.3.0, ROMFS : Version Blinking in blue color...
Page 12
(4) Brightens/Contrast Adjust -1 (5) Brightens/Contrast Adjust -2 - Adjust brightness value of the RX terminal - Adjust brightness value of the RX terminal when value less than - Contrast has default of "138", not changed.(Number check "-11" is required requied) - Input signal: None - Brightness Spec : 0.60~0.75 cd/m2...
Page 13
(6) Button Test (7) Battery Test - Test whether there is key control operation of the RX - Battery information display Test Items Test Items (MICOM : 1.3.0, ROMFS : (MICOM : 1.3.0, ROMFS : Remained battery capacity display (%) 1.2 12/21 ENG), TX SSID : 1.2 12/21 ENG), TX SSID : Non-mounting of battery: N/A...
TROUBLESHOOTING 1. OUT OF ORDER ON POWER (TX) NO POWER (POWER INDICATOR OFF) Check Check PWRIN signal 16V or Connector(J1007) Replace Power Adapter on Main Board Fail Fail on Power Adapter Pass Check Check 5V signal Replace or check soldering LTC1628(U1006) on VCC5.0V_VCT on Main of LCT1628 (U1006)
Page 17
2. OUT OF ORDER ON BOOTING (TX) No Booting Check Check Replace or check soldering VCC3.3V signal on Main LTC1628 (U1006) on of LCT1628 Board Fail Main Board Fail Replace or check soldering Pass Check VCC1.8V signal of FAN1117(U1001) Fail Check 6MHz Crystal (X1402) Check Crystal circuit...
Page 18
3. OUT OF ORDER ON MPEG (TX) No MPEG Encoding or Encoding Error Check Replace or check soldering VCC1.25V signal on of FAN1117(U1001) Fail Main Board Pass Check MPEG_27M signal on Check 27MHz OSC Block Main Board Fail Pass Check Check bonding of clock signal (135MHz) of CX23416 (U502) or...
Page 19
4. OUT OF ORDER ON TV (TX) NO TV Signal or Noise (POWER INDICATOR OK) Check Check Reprogram or Replace VCC33V signal on PWM_50KHZ signal on VCT4973(U603) Main Board Main Board Fail Fail Check Pass TR & Diode on TV Tuner Replace TR &...
Page 20
5. POWER PART(POWER BOARD) (RX) No Power Check DCIN Replace Adapter 16V or not? Check the voltage of the pin no. Replace Q205 1 & 3 on Q205. 16V or not ? Check the voltage of the pin No. 24 Replace R206 on U301.
Page 21
6. POWER PART(MAIN BOARD) (RX) No power Check blue LEDs. Check VCC3.3VSB and ON or not? U1202. Check the voltage of pin No. 1 on Check R1204, CB1204, Q1902. U1201 and U1202 3.3V or not ? Check the voltage of pin No. Replace Q1901 5,6,7and 8 on Q1901.
Page 22
7. VIDEO PART (RX) No video Check VCCINV Replace Q206 on the 16V or not ? Power Board Check Replace Cable and check Inverter Cable J302 on the power Board OK or not ? Check VCCLCD Check Q1904 5V or not ? Check the clock of pin no.
Page 23
8. AUDIO PART (RX) No audio Check Connect the cable on connection of Cable on J1301 J1301 OK or not ? Check connection of Speaker Connect the Speaker Cable Cable OK or not ? Check the voltage of FB1302 Check FB1302 5V or not ? Check the Check U1302, C1301,...
Page 24
9. BETTERY PART (RX) Can’t battery-charging Check the battery Correct the battery connection connection OK or not ? Check connection of the cable Check the Cable between J201 on power connection board and J1901 on main board OK or not ? Check voltage of pin no.
LVDS device. The LVDS device interfaces with LCD module. 2. Wireless LAN The Wireless LAN Card which is used in the product is manufactured by LG Innotek. The card satisfied with IEEE802.11 b/g standard. The product name is LVMM-3001A.
Page 28
WIRELESS TV TX BOARD BLOCK DIAGRAM (TX) PCI Rev 2.1 compliant S3C2800 VCT4973 PWR_ Power Wireless LAN On/Off Block P_AD[0..31] Controller POWER_ Power Tact TACT Switch P_AD[0..31] SDA_1 Video Memory SCL_1 TV_Tuner 8Mbytes MPEG Encoder SDA_1 CX23416 SCL_1 VIDIN[0..7] Video ADC Flash RGB(3) MST9883C...
Page 29
5. TV Tuner TV Tuner is LG INNOTEK Inc. TAEW-G351P. SAW Filter is not included to the tuner and internal booster is included to the tuner. The tuner adopts external 2 Antenna Connectors. One is for input TV signal and the other is output TV signal. TV tuner is controlled by VCT4973 through IIC interface.
EXPLODED VIEW PARTS LIST PART NO. DESCRIPTION 3313T15103A MAIN TOTAL ASSEMBLY, 15LW1R-UA BRAND ML-042A 3551TKK545A COVER ASSEMBLY, 15LW10 TOTAL . TOP ASSY(TX) 4815TKK043A SHIELD ASSEMBLY, TOP MAIIN(15LW10) 6871TMT787B PWB(PCB) ASSEMBLY,MAIN, 15LW10 TX BRAND ML- 042A TOTAL 4814TKK290A SHIELD, REAR .
REPLACEMENT PARTS LIST For Capacitor & Resistors, the CC, CX, CK, CN, CH : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit in the CQ : Polyestor RS : Metal Oxide Film P/No. means as follows; CE : Electrolytic RN : Metal Film CF : Fixed Film RH : CHIP, Metal Glazed(Chip)