Advertisement
Quick Links
StorageWorks™ by Compaq
Replacing an
External Cache
Battery (ECB)
Open Card Completely Before
Beginning Installation Procedures
© 2002 Compaq Information Technologies Group, L.P.
Compaq, the Compaq logo, and StorageWorks are trademarks of Compaq
Information Technologies Group, L.P.
All other product names mentioned herein may be trademarks of their
respective companies.
Compaq shall not be liable for technical or editorial errors or omissions
contained herein. The information is provided "as is" without warranty of
any kind and is subject to change without notice. The warranties for
Compaq products are set forth in the express limited warranty statements
accompanying such products. Nothing herein should be construed as
constituting an additional warranty.
Printed in the U.S.A.
Replacing an External Cache Battery (ECB)
Fifth Edition (May 2002)
Part Number: EK–80ECB–IM. E01
Compaq Computer Corporation
About This Card
This document contains instructions for replacing the ECB in a
StorageWorks™ HSG60, HSG80, HSJ80, HSZ70, or HSZ80
subsystem.
For instructions on upgrading a single-controller configuration
to a dual-redundant controller configuration, refer to the
appropriate array controller user guide or maintenance and
service guide.
ECB replacement procedures provided in this card include:
•
HSZ70 Single-Controller
•
HSZ70 Dual-Redundant Controller
•
HSG60 and HSG80 Controller
•
HSJ80 Controller
Configurations, page 5
•
HSZ80 Controller
Configurations, page 6
•
Hot-Pluggable Procedure for StorageWorks Model 2100
and 2200
Enclosures, page 6
General Information
The type of ECB used depends on the StorageWorks controller
enclosure type.
WARNING: The ECB is a sealed, rechargeable, lead acid
battery that must be recycled or disposed of properly
according to local regulations or policies after replacement.
Do not incinerate the battery. Improper handling may cause
personal injury. The ECB displays the following label:
Figure 1
and
Figure 2
provide general information about the
ECBs used with many StorageWorks controller enclosures.
.
1 Battery disable switch (SHUT
OFF)
2 Status LED
Figure 1: Single ECB for single-controller configurations
Configurations, page 3
Configurations, page 3
Configurations, page 4
1
2
CXO5715B
3 ECB Y-cable
3
Advertisement
Related Manuals for Compaq StorageWorks HSG60
Summary of Contents for Compaq StorageWorks HSG60
- Page 1 Figure 1 Figure 2 provide general information about the Compaq shall not be liable for technical or editorial errors or omissions ECBs used with many StorageWorks controller enclosures. contained herein. The information is provided “as is” without warranty of any kind and is subject to change without notice. The warranties for Compaq products are set forth in the express limited warranty statements accompanying such products.
- Page 2 T U S S T A CXO6864A CXO5713B CXO5608B 3 ECB Y-cable 1 Battery disable switch (SHUT 1 B1 supports cache B 5 Controller A 4 Faceplate and controls for OFF) 2 B2 supports cache B 6 Controller B second battery (dual ECB 2 Status LED configuration only) 3 A2 supports cache A...
- Page 3 HSZ70 Single-Controller Configurations 8. Remove the old ECB and place the ECB in an antistatic bag or on a grounded antistatic mat. Use the following steps and Figure 1 Figure 2 to replace an ECB: HSZ70 Dual-Redundant Controller 1. Is the controller operating? Configurations •...
- Page 4 “other controller” maintenance port. b. Install a Battery Service Label on the replacement ECB The connected controller now becomes “this as described by the Compaq StorageWorks ECB Battery controller.” Service Label Placement installation card. b. Repeat...
- Page 5 Insert the replacement ECB into an appropriate bay or near the ECB being removed. a. Install a Battery Service Label on the replacement ECB as described by the Compaq StorageWorks ECB Battery c. Follow on-screen instructions to connect the ECB. Service Label Placement installation card.
- Page 6 b. Follow on-screen instructions to connect the ECB. NOTE: If an empty bay is not available, place the replacement ECB on top of the enclosure or at the bottom of the rack. Figure 4 for the location of the Cache A (7) and Cache B (8) modules.
- Page 7 2200 Enclosure ECB LED Definitions Table 1 replaces Table 6–1 “ECB Status LED Displays” in the Compaq StorageWorks Model 2100 and 2200 Ultra SCSI Controller Enclosure User Guide. IMPORTANT: Make sure to identify the existence of this updated table in the user guide.