Page 1
LCD TV SERVICE MANUAL CHASSIS : LJ71A MODEL : 23LS7D 23LS7D-JA CAUTION BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
SAFETY PRECAUTIONS IMPORTANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards.
SPECIFICATION NOTE : Specifications and others are subject to change without notice for improvement. 1. Application range 3. Test method This specification sheet is applied to the 20”/ 23” Wide LCD (1) Performance : LGE TV test method followed Digital TV used LJ71A chassis. (2) Demanded other specification Safety : JQA Specification 2.
Page 5
5. Module Specification 5.1. 23”LCD Module (AUO T230XW01 V3) Item Typ. Unit Remark Display area 508.152 (H) x 285.696 (V) Outline dimension 546.0 (H) x 318.3 (V) x 46.0 (D) Number of Pixels 1366 (H) x 768(V) 1Pixel=3RGB Cells Cell pitch 372 μm (H) x 372 μm (V) μm 1Pixel=3RGB Cells...
Page 6
6. Model Specification Item Specification Remark Analog-terrestrial Broadcasting system NTSC-M RF Input Channel VHF : 1~12 UHF : 13~62 CATV : C13~C38 Digital-terrestrial Broadcasting system ISDB-T RF Input Channel 000~999 CH. Logical CH Number Digital-BS/SC Broadcasting system ISDB-S RF Input Channel 000~999 CH.
ADJUSTMENT INSTRUCTION 1. Application Range This specification sheet is applied to 20”/ 23” LCD TV which is manufactured in TV (or Monitor) Factory or is produced on the basis of this data. filexxx.bin (7) ..OK 2. Specification 1) The adjustment is according to the order which is designated and which must be followed, according to the plan which can be changed only on agreeing.
Page 8
4. Total Assembly line process 4.5. Power Consumption 1) Press “EYE” button on LG Adjust remocon and check 4.1. Adjustment Preparation whether LED color is amber or not. 2) Press “POWER” button on LG Ajust remocon to enter - Above 30 minutes H/run in RF no signal Stand-by mode.
Page 9
(If Pressed “EYE” button on LG ADJUST REMOCON, Color of Power LED will be Amber) 2) Press “IN-STOP” button on LG ADJUST REMOCON. It is executed 3~15 procedure automatically by Software program.(If pressed “IN-STOP” button, Color of “...
Page 10
5.2 EEPROM DATA READ (1) Signal Table Delay 100ms 128 Bytes (2) Command Set Adjustment contents CMD(hex) ADH(hex) ADL(hex) Details EEPROM READ 0-Page 0~7F Read 0-Page 80~FF Read 1-Page 0~7F Read 1-Page 80~FF Read 2-Page 0~7F Read 2-Page 80~FF Read 3-Page 0~7F Read 3-Page 80~FF Read * Purpose : To read the appointment Address of E...
TROUBLE SHOOTING 1. No Power (LED indicator off) : [A] Process Fail Check 12V or Check short of Main B/D ST_5V of Power B/D. or Change Power B/D. Pass Fail Fail Check short of Re-soldering or Change Check Output of IC100, Q308.
Page 12
2. No RASTER : [B] Process Fail Check LED status Repeat A PROCESS. On Display Unit. Pass Fail Check Panel Link Change Panel Link Cable or Module. Cable or Module. Pass Fail Check Inverter Change Inverter Connector or Inverter. Connector or inverter.
Page 13
3. No RASTER on DTV Signal Repeat [A,B] process Pass Fail Check the input/ Check the P901. output of R918. Pass Fail Check the input/ Re-soldering or Change the defect part. output of R127. Pass Fail Check the input/ Re-soldering or change the defect part. output of IC100 Check the X100 Pass...
Page 14
4. No Raster on Component Signal Repeat [A, B] process. Pass Fail Check the input/ Check the J801. output of R806. Pass Fail Check Re-soldering or Change the defect part. the input/output of R121. Pass Fail Check the Re-soldering or change the input/output of IC100.
Page 15
5. No Raster on HDMI Signal Repeat [A, B] process. Pass Fail Re-soldering or change the Check the input/ defect part, Check the X100. output of IC100. Pass Check input source cable and jack. 6. No Raster on AV (Video, 7.
Page 16
8. No sound Fail Check the input Change the source input. Source. Pass Fail Re-soldering of Change the defect part. Check input/Output Check the X110 of IC100. Pass Fail Re-soldering or Change Check the input/ the defect part. output of IC500 Pass Fail Change Speaker.
Page 28
SMAW200-05P 5P 2.00MM 1R ANGLE DIP ST NATU P305 6602T20009G SMAW200-08P 8P 2.00MM 1R ANGLE DIP ST NATU MFL39444601 Manual,Owners USER LJ71A LG 20/23LS7D-JA Japane P4000 6602T20009G SMAW200-08P 8P 2.00MM 1R ANGLE DIP ST NATU 4950TKA320A Plate PRESS SBHG T1.2 SUPPORT UPSET...
Page 45
Aug., 2007 P/NO : MFL38623703 Printed in Korea...