Page 1
Koninklijke Philips Electronics N.V. or their respective owners. TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
Koninklijke Philips Electronics N.V. or their respective owners. TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
Product information is subject to change without notice. TV Bottom • detailed product information, please visit Audio out – Optical Toslink • www.philips.com/support Network LAN – RJ45 • YPbPr, L/R • HDMI 4 in – ARC Display Type • HDMI 3 in - ARC •...
Page 4
– • Limitations : software(DMS class) Maximum supported total bit rate for a media file is You can use the Philips TV Remote app (iOS and – – 30Mbps. Android) on mobile devices. Maximum supported video bit rate for a media file is –...
4. Switch “off” the set, and remove the wire between the to the diversity tables for the correct values. • The correct component values are listed on the Philips two pins of the Mains/AC Power plug. • Check the cabinet for defects, to prevent touching of any Spare Parts Web Portal.
Page 6
• Mix of lead-free soldering tin/parts with leaded soldering tin/parts is possible but PHILIPS recommends strongly to avoid mixed regimes. If this cannot be avoided, carefully clear the solder-joint from old tin and re-solder with new tin.
Page 7
• Always respect voltages. While some may not be originating from the USA and used e.g. in dangerous in themselves, they can cause unexpected LATAM and AP-NTSC countries reactions that are best avoided. Before reaching into a B-TXT Blue TeleteXT powered TV set, it is best to test the high voltage Centre channel (audio) insulation.
Page 8
G-TXT Green TeleteXT distance is 6.5 MHz. L' is Band I, L is all H_sync to the module bands except for Band I High Definition LG.Philips LCD (supplier) Hard Disk Drive Loudspeaker HDCP High-bandwidth Digital Content Protection: LVDS Low Voltage Differential Signalling A “key”...
Page 9
Serial Peripheral Interface bus; a 4-wire module, implementing the CA system for a synchronous serial data link standard host (e.g. a TV-set) S/PDIF Sony Philips Digital InterFace Power On Reset, signal to reset the uP SRAM Static RAM PSDL Power Supply for Direct view LED...
Page 10
Thin Film Transistor toward external amplifier Total Harmonic Distortion Vestigial Side Band; modulation method TMDS Transmission Minimized Differential WYSIWYR What You See Is What You Record: record Signalling selection that follows main picture and Transport Stream sound TeleteXT WXGA 1280 × 768 (15:9) TXT-DW Dual Window with TeleteXT XTAL...
3.2 Assembly/Panel Removal 3.2.1 Stand/Base removal Common: 1. Remove the fixation screws [1] that secure the stand. 2. Take the stand bracket out from the set. 3.2.2 IR board Control Unit Common: 1. Unplug the connector from the SSB. Caution: be careful, as these are very fragile connectors! 2.
Page 15
3.2.3 Rear Cover Warning: Disconnect the mains power cord before removing the rear cover. 7303series: 1. Remove all fixation screws [2] and [3] that secure the Back cover assy. 2. Unplug the connector [2] that marked by red box below from SSB. 3.
Page 16
2.2.4 Keyboard Control Unit Caution: be careful, the Keyboard is catch on the Back cover, please be careful to avoid damage the fragile connectors! 1. Remove all the fixation screws [1]. 2. Release the connector [2] then take it out from back cover. When defective, replace the whole unit.
Page 17
3.2.6 Power Supply Unit (PSU) Caution: it is mandatory to remount all different screws at their original position during re-assembly. Failure to do so may result in damaging the PSU. 1. Gently unplug all connectors from the PSU. 2. Remove all fixation screws from the PSU. 3.
4. Service Modes 4.1 Service Modes The Service Mode feature is split into following parts: Service Alignment Mode (SAM). Factory Mode. Customer Service Mode (CSM).SAM and the Factory mode offer features, which can be used by the Service engineer to repair/align a TV set. ...
Page 19
With the “LEFT/RIGHT” keys, it is possible to: – (De) activate the selected menu item. – (De) activate the selected sub menu. – Change the value of the selected menu item. When you press the MENU button once while in top level SAM, the set will switch to the normal user menu (with the SAM mode still active in the ...
Page 20
Public Broadcasting Service password Reset. etc. How to Activate the Factory mode To activate the Factory mode, use the following method: Press the following key sequence on the remote control transmitter: from the “menu/home” press “1999”, directly followed by the “Back/Return”...
Page 21
Line number for every line (to make CSM language independent). Set the screen mode to full screen (all contents on screen is visible). After leaving the Customer Service Mode, the original settings are restored. Possibility to use “CH+” or “CH-” for channel surfing, or enter the specific channel number on the RC. How to Activate CSM To activate CSM, press the following key sequence on a standard remote control transmitter: “123654”...
5. Software Upgrading, Error code and Panel Code 5.1 Software Upgrading Step 1: Ready for F/W Upgrade 1. Rename the software as “autorun.upg”. 2. Prepare a USB memory (File format: FLAT, Size: 1G~8G). 3. Copy the software to USB flash disk (root directory). Note the version of this F/W before you change the software file name.
Page 23
4. Press OK to start software upgrade 5. Upgrade in progress...
Page 24
Step 3: Check the SW version 1. After burning software, TV will restart. 2. Press “123654”, enter Customer Service Mode to check if the software version is correct. Caution: Please make sure that software upgrade is finished before unplug the USB and AC power! 5.2 Error Code 5.2.1 Introduction Error codes are required to indicate failures in the TV set.
Page 25
5.2.3 Error codes overview In this chassis only “layer 2” error codes are available and point to problems on the SSB. They are triggered by LED blinking when CSM is activated. Only the following layer 2 errors are defined: 5.2.4 How to Clear the Error Buffer The error code buffer is cleared in the following cases: •...
Page 26
5.3 Set Option Code For all models of TPM18.1E_LA chassis, a SET OPTION code is used instead of the DISPLAY OPTION code. The Set Option Code feature allows using one single Set Option number to define all settings for a specific TV set type. 5.3.1 Where to find the Set Option Code Refer to the stickers on the TV set.
Page 27
CTN_ALT BOM# Panel Type Panel ID 50PUT7303/56 TPT500U1-QVN03.U S7B0M 50PUT7303/79 TPT500U1-QVN03.U S7B0M 50PUT7303/98 TPT500U1-QVN03.U S7B0M 55PUT7303/56 TPT550U1-QVN05.U S57B0F 55PUT7303/79 TPT550U1-QVN05.U S57B0F 55PUT7303/98 TPT550U1-QVN05.U S57B0F 65PUT7303/56 TPT650UA-QVN06.U S300AL 65PUT7303/79 TPT650UA-QVN06.U S300AL 65PUT7303/98 TPT650UA-QVN06.U S300AL Result: After accepting the Set Option Code the TV set stores the following items in NVM: - the TV Set type (Model Number), - the related option codes, and the default White Point values.
Trouble shooting 2016年12月10日 2016/4/8 Picture-related Intermittent Ask Photo Picture ? problem ? Menu Smarkt Signal SW latest ? Backlight? issue function? issue SSB+LVDS+Panel Update SW LED working ? PSU/SSB Problem solved ? Sound ? PSU+ Panel Finish SW+SSB...
Page 29
Trouble shooting 2016年12月10日 2016/4/8 Audio/Sound- related Intermittent Sound ? problem ? Setting SW latest ? Mute ? issue issue Update SW Extra device Check extra connect? device Problem solved ? Factory setting Finish Sound back ? Setting issue SSB+SPK...
Page 30
6.Slow response to user interaction 7.Switches ON by itself 8.Switches Off by itself 9.Stuck in standby mode / unable to start up 10.Stuck on PHILIPS / ANDROID logo 11.CAM not recognized by TV 12.CAM authentication issue 13.Misc CAM issue 14.IP-EPG issues 15.BC-EPG issues...
7. Electrical Diagram 7.1 Block diagram 7.2 Power Supply Power architecture of this platform. AUDIO LVDS Platform power Display power CN8601 ON/OFF PS_ON Platform 12V_A MT5596 24V_A 3.5_STB CN1190 AC-input + Main filter AC IN...
Page 32
7.3 Power tree WiFi & BT/ VCC U4251 +5V-WIFI RT6217 MT5596/ AVDD1V0-STB U4308 +3V5-SB +1V0-AVDD G9661 U4309 MT5596/ AVDD33-ETH-STB +3V5-SB RT6217 U4304 +3V5-SB MT5596/ AVDD33-STB +3V3-STANDBY RT9193-33GB power for RC off MT5596/ DDRV U1701 U4302 +5V_SW +12V +1V5-DDR 600 mA DDR (X 5)/ VDD SY8368 RT8079ZQW...
Page 33
7.4 Power layout SSB L4304 +3.5V_SB C4457 +12V AMBI C777 TUNER LNB C4309 +3.3V STANDBY L4101 +2.5V NT C4344 +1.8V EMMC-IO CM47 +1.5V DDR Power SSB Top View (For 715G8579M)
9.5 E 715G8555 Keyboard control panel 9-5-1 Key Joystick key define CONN TO SSB JOYSTICK Direction switch Key function Resistance Voltage Range Center 2-5 short Menu 0.0 to 0.22 V CN01 CN04 Right 1-5 short 0.5V 0.39 to 0.60 V KEY 1 AMBI_SPI_CLK Left...