Haier H2SM-18HC03/R2 Installation Manual
Haier h2sm-18hc03/r2: user guide
Hide thumbs
Also See for H2SM-18HC03/R2:
- Operation manual (21 pages) ,
- Operating manual (57 pages) ,
- Service manual (56 pages)
Table of Contents
Advertisement
Quick Links
Installation Manual of Room Air Conditioner
Necessary Tools for Installation
1.Driver
2.Hacksaw
3.Hole core drill
4.Hexagon wrench (5mm)
Accessory parts
No.
Accessory parts
Remote controller
R-03 dry battery
Mounting plate
Drain hose
4X25
Plastic cap
Screw
Cushion
Drain-elbow
NO.0010510475
5.Spanner(14,17,19 and 24 mm)
6.Torque wrench(17mm,22mm,24mm)
7.Pipe cutter
8.Flaring tool
Drawing for the installation of indoor and outdoor units
Number
of
articles
Optional parts for piping
Mark
Parts name
Non-adhesive tape
Adhesive tape
Saddle(L.S) with screws
Connecting electric cable
for indoor and outdoor
Drain hose
Heating insulating material
Piping hole cover
Arrangement of piping directions
Left
Read this manual before installation
Explain sufficiently the operating means to the user
according to this manual.
9.Knife
10.Nipper
11.Gas leakage detector or
soap-and-water solution
Rear left
Rear
right
Right
Below
The marks from
The distance between the indoor unit and the floor should be
more than 2m.
12.Measuring tape
13.Reamer
14.Refrigerant oil
Attention must be paid to
the rising up of drain hose
to
in the figure are the parts numbers.
A
G
Advertisement
Table of Contents
Related Manuals for Haier H2SM-18HC03/R2
Summary of Contents for Haier H2SM-18HC03/R2
-
Page 1: Installation Manual Of Room Air Conditioner
Installation Manual of Room Air Conditioner Necessary Tools for Installation 1.Driver 5.Spanner(14,17,19 and 24 mm) 2.Hacksaw 6.Torque wrench(17mm,22mm,24mm) 3.Hole core drill 7.Pipe cutter 4.Hexagon wrench (5mm) 8.Flaring tool Accessory parts Number Accessory parts articles Remote controller Mark R-03 dry battery... -
Page 2: Selection Of Installation Place
HSU-22HC03/R2(DB) Fixing of outdoor unit Selection of Installation Place Indoor Unit Place, robust not causing vibration, where the body can be supported sufficiently. Place, not affected by heat or steam generated in the vicinity, where inlet and outlet of the unit are not disturbed. Place, possible to drain easily, where piping can be connected with the outdoor unit. -
Page 3: Indoor Unit
1.Fitting of the Mounting Plate and Positioning of the wall Hole When the mounting plate is first fixed 1.Carry out, based on the neighboring pillars or lintels, a proper leveling for the plate to be fixed against the wall, then temporarily fasten the plate with one steel nail. 2. -
Page 4: Installation Of The Indoor Unit
3.Installation of the Indoor Unit Drawing of pipe Rear piping Draw pipes and the drain hose, then fasten them with the adhesive tape Left Left-rear piping In case of left side piping, cut away, with a nipper, the lid for left piping. In case of left-rear piping, bend the pipes according to the piping direction to the mark of hole for left-rear piping which is marked on heat insulation materials. - Page 5 When connecting the cable after installing the indoor unit 1. Insert from outside the room cable into left side of the wall hole, in which the pipe has already existed. 2. Pull out the cable on the front side, and connect the cable making a loop. Insert the cable from the back side of the unit, then pull it out on the front side.
-
Page 6: Installation Of Outdoor Unit
20 g/m. But the charge of refrigerant must be conducted by professional air conditioner engineer. Before adding additional refrigerant, perform air purging from the refrigerant pipes and indoor unit using a vacuum pump,then charge additional refrigerant. - Page 7 After attaching the each caps, check the gas leakage around the caps. CAUTION: 1.If the refrigerant of the air conditioner leaks, it is necessary to discharge all the refrigerant. Vacuumize first, then charge the liquid refrigerant into air conditioner according to the amount marked on the name plate.
- Page 8 1.Power Source Installation The power source must be exclusively used for air conditioner. (Over I0A) In the case of installing an air conditioner in a moist place, please install an earth leakage breaker. For installation in other places, use a circuit breaker as far as possible.