Finishing; Connection Pipe, Cable And Drain Hose; Front Panel Removal And Installation; Intake Grille Removal And Installation - Fujitsu AirStage AS A009GCGH Series Installation Manual
Indoor unit (wall mounted type)
Hide thumbs
Also See for AirStage AS A009GCGH Series:
- Design & technical manual (1092 pages) ,
- Installation manual (14 pages) ,
- Operating manual (8 pages)
Table of Contents
Advertisement
6.5.2 External output
• A twisted pair cable (22AWG) should be used. Maximum length of cable is 25m.
• Use an external input and output cable with appropriate external dimension, depending
on the number of cables to be installed.
• Output voltage: Hi DC12V±2V, Lo 0V.
• Permissible current: 50mA
Output select
● When indicator etc. are connected directly
Operation
indicator
Error
indicator
Indoor unit Fan
status indicator
connected unit
● When connecting with unit equipped with a power supply
Connected
device 1
Connected
device 2
Connected
device 3
connected unit
Relay (Locally purchased)
Operation behavior
Connector
External output 1
Pins 1-2
External output 2
CNB01
Pins 1-3
External output 3
Pins 1-4
7. FINISHING
After checking for gas leaks (refer to the Installation Manual of the outdoor unit), perform
this section.
Install heat insulation around both the large (gas) and small (liquid) pipes. Failure to do
so may cause water leaks.
7.1. Connection pipe, cable and drain hose
Insulate the drain hose, if necessary, to prevent it from freezing.
(1) Insulate between pipes.
• For (A) Rear, (B) Right and (C) Bottom piping, overlap the connection pipe heat insula-
tion and indoor unit pipe heat insulation and bind them with vinyl tape so that there is no
gap.
• For (D) Left bottom piping, (E) Left piping, (F) Left rear piping, butt the connection pipe
heat insulation and indoor unit pipe heat insulation together and bind them with vinyl
tape so that there is no gap.
((A) Rear, (B) Right and (C) Bottom piping)
Connection pipe
(heat insulation)
Bind the pipes together so
that there is no gap.
Seal A is used when the diameter
of gas pipe is Ø12.70 or more.
(For (D) Left bottom piping, (E) Left piping, (F) Left rear piping)
• Wrap the area which accommodates the
rear piping housing section with cloth tape.
En-11
P.C.B
P.C.B
Output voltage
Status
0V
Stop
DC 12 V
Operation
0V
Normal
DC 12 V
Error
0V
Indoor unit fan stop
DC 12 V
Indoor unit fan operation
CAUTION
Overlap the insulation.
Indoor unit pipe
(heat insulation)
Vinyl tape
Butt connection pipe (heat insulation) against
the indoor unit pipe (heat insulation) and wrap
with seal A so that there is no gap.
Connection pipe
Indoor unit pipe
Wrap with cloth tape.
Cloth tape (Accessories)
• Bind the connection cable with
vinyl tape.
• Bundle the piping and drain hose
together by wrapping them with
cloth tape over the range within
which they fit into the rear piping
housing section.
(2) Temporarily fasten the connection
cable along the connection pipe with
vinyl tape.
(3) Fasten the connection pipe to the
outside wall with a saddle, etc.
CNB
(4) Fill the gap between the outside wall
01
pipe hole and the pipe with sealer
so that rain water and wind cannot
blow in.
(5) Fasten the drain
hose to the outside
wall, etc.
CNB
01
GOOD
Drain
hose
Saddle
8. FRONT PANEL REMOVAL AND INSTALLATION
8.1. Intake grille removal and installation
Intake grille removal
Open the intake
grille. While gently
pressing the left and
right mounting shafts
of the intake grille
outward "a", remove
the intake grille in
direction of the ar-
row "b".
Press 4 places on the intake grille to close it com-
pletely.
8.2. Front panel removal
(1) Remove intake grille
(Reference the intake grille
removal.)
(2) Remove 3 caps.
(3) Remove wire cover.
(4) Remove 7 screws.
(5) The front panel is pulled to the
front, raising the upper surface, and
a front panel is removed.
Connection cable (Power supply cable)
Vinyl tape
Connection cable
(Transmission and remote controller cable)
Wrap with cloth tape
Pipe
Cloth tape
Drain hose
Saddle*
Wall
Pipe
PROHIBITED
Lifted up
Wave
Intake grille installation
While holding the
grille horizontal, set
the left and right
mounting shafts into
a
the pillow blocks
b
at the top of the
panel "c". To latch
each shaft properly,
insert the shaft until
it snaps.
Screws (Wire cover )
Caps ( 3 position )
Pipe
Outside wall cap*
Sealer putty*
(Outdoors)
*Locally purchased
End in water
c
Wire cover
Screws ( 6 position )
Advertisement
Table of Contents
