All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by ER/TY 1072 BU TV Consumer Care, the Netherlands...
Not all (circuit-) descriptions and (block-) schematics in this Service Manual apply to all sets. Use the hyperlinks in this table to lead you through this manual. Directions for Use You can download this information from the following websites: http://www.philips.com/support http://www.p4c.philips.com back to 2010-Dec-29 div. table...
Page 3
Technical Specifications, and Connections Q552.1L LA EN 3 Connections 18990_001_100401.eps 100401 Figure 2-1 Connection overview Note: The following connector color abbreviations are used - D1+ Data channel (acc. to DIN/IEC 757): Bk= Black, Bu= Blue, Gn= Green, Gy= - Shield Grey, Rd= Red, Wh= White, Ye= Yellow.
Page 4
EN 4 Q552.1L LA Technical Specifications, and Connections - CT Centre Tap: DC level fixation 11 - Shield - RD- Receive signal 12 - CLK- Data channel - GND 13 - Easylink/CEC Control channel - GND 14 - ARC Audio Return Channel 15 - DDC_SCL DDC clock 16 - DDC_SDA...
3.3.3 Spare Parts external damage. • Check the strain relief of the Mains/AC Power cord for For the latest spare part overview, consult your Philips Spare proper function. Part web portal. • Check the electrical DC resistance between the Mains/AC...
Page 6
EN 6 Q552.1L LA Precautions, Notes, and Abbreviation List The third digit in the serial number (example: Abbreviation List AG2B0335000001) indicates the number of the alternative B.O.M. (Bill Of Materials) that has been used for producing the 0/6/12 SCART switch control signal on A/V specific TV set.
Page 7
6.5 MHz. L' is Band (VESA standard for communication I, L is all bands except for Band I channel and display). Using E-DDC, LG.Philips LCD (supplier) the video source can read the EDID Loudspeaker information form the display.
Page 8
SOPS Self Oscillating Power Supply Serial Peripheral Interface bus; a 4- wire synchronous serial data link standard S/PDIF Sony Philips Digital InterFace SRAM Static RAM Service Reference Protocol Small Signal Board Spread Spectrum Clocking, used to reduce the effects of EMI...
Mechanical Instructions Q552.1L LA EN 9 4. Mechanical Instructions Index of this chapter: Notes: 4.1 Cable Dressing van Gogh & da Vinci styling (5000 & 6000 • Figures below can deviate slightly from the actual situation, series) due to the different set executions. 4.2 Cable Dressing Matisse styling (8000 series) 4.3 Service Positions 4.4 Assy/Panel Removal Van Gogh Styling (5000 series)
Page 10
EN 10 Q552.1L LA Mechanical Instructions 19030_101_100810.eps 100810 Figure 4-2 Cable dressing 40" back to 2010-Dec-29 div. table...
Page 11
Mechanical Instructions Q552.1L LA EN 11 19030_102_100810.eps 100810 Figure 4-3 Cable dressing 46" back to 2010-Dec-29 div. table...
Page 12
EN 12 Q552.1L LA Mechanical Instructions Cable Dressing Matisse styling (8000 series) 19030_103_100810.eps 100810 Figure 4-4 Cable dressing 40" back to 2010-Dec-29 div. table...
Page 13
Mechanical Instructions Q552.1L LA EN 13 19030_104_100810.eps 100812 Figure 4-5 Cable dressing 52" back to 2010-Dec-29 div. table...
Page 14
EN 14 Q552.1L LA Mechanical Instructions Service Positions For easy servicing of a TV set, the set should be put face down on a soft flat surface, foam buffers or other specific workshop tools. Ensure that a stable situation is created to perform measurements and alignments.
Page 15
Mechanical Instructions Q552.1L LA EN 15 4.4.2 Speakers 4.4.5 Mains Switch Tweeters The mains switch is mounted on the front bezel with two Each tweeter unit is mounted with one screw. screws. When defective, replace the whole unit. 4.4.6 IR & LED Board Subwoofer The central subwoofer is located in the centre of the set, and is Refer to...
Page 16
EN 16 Q552.1L LA Mechanical Instructions 4. Remove the connectors [4] on the IR/LED board. 4.4.7 Keyboard Control Board Refer to Figure 4-23 for details. 1. Unplug the connector on the IR & LED board that leads to the Keyboard Control board as described earlier. 2.
Page 17
Mechanical Instructions Q552.1L LA EN 17 4.5.1 Rear Cover 18970_113_100326.eps 100326 Figure 4-17 Rear cover removal (32") Warning: Disconnect the mains power cord before removing the rear cover. Figure 4-17. 1. Remove fixation screws [2] and [3] that secure the rear cover.
Page 18
EN 18 Q552.1L LA Mechanical Instructions 4.5.3 Main Power Supply 4.5.6 IR & LED Board Refer to Figure 4-18 for details. Refer to Figure 4-20, Figure 4-21 Figure 4-22 for details. 18770_142_100215.eps 100215 18970_103_100323.eps 100323 Figure 4-20 IR & LED Board -1- Figure 4-18 Main Power Supply 1.
Page 19
Mechanical Instructions Q552.1L LA EN 19 4.5.7 Local Control Board Refer to Figure 4-23 for details. 1. Unplug the connector on the IR & LED board that leads to the Local Control board as described earlier. 2. Release the cable from its clamps/tape. 3.
Page 20
EN 20 Q552.1L LA Mechanical Instructions 2. Lift the rear cover from the TV. Make sure that wires and 4.6.5 IR & LED Board flat coils are not damaged while lifting the rear cover from the set. Refer to Figure 4-27 for details.
Page 21
Mechanical Instructions Q552.1L LA EN 21 11. Remove the Ambilight PWBs as earlier described. Now the LCD Panel can be lifted from the front cabinet. 12. Tilt the Ambilight subframes [5] after having removed the screw. 18771_112_100504.eps 100504 Figure 4-29 LCD Panel Pay special attention to use the correct screws at the proper location when mounting a new LCD panel! Using the wrong screws will damage the LCD panel!
EN 22 Q552.1L LA Service Modes, Error Codes, and Fault Finding 5. Service Modes, Error Codes, and Fault Finding Index of this chapter: • All service-unfriendly modes (if present) are disabled, like: 5.1 Test Points – (Sleep) timer. 5.2 Service Modes –...
Page 23
“OK” button on the RC. Code Contents of SAM (see also Table 6-11) 39mm • Hardware Info. PHILIPS – A. SW Version. Displays the software version of the MODEL: 32PF9968/10 main software (example: Q555X-1.2.3.4 = PROD.SERIAL NO: AG 1A0620 000001 AAAAB_X.Y.W.Z).
Page 24
EN 24 Q552.1L LA Service Modes, Error Codes, and Fault Finding • NVM editor. For NET TV the set “type number” must be How to Activate CSM entered correctly. Also the production code (AG code) can be entered here Key in the code “123654” via the standard RC transmitter. via the RC-transmitter.
Page 25
Service Modes, Error Codes, and Fault Finding Q552.1L LA EN 25 • Event counter : Stepwise Start-up S : 000X 0000(number of software recoveries : SW EVENT-LOG #(reboots) When the TV is in a protection state due to an error detected by S : 0000 000X (number of software events : SW EVENT- stand-by software (error blinking is displayed) and SDM is LOG #(events)
Page 26
EN 26 Q552.1L LA Service Modes, Error Codes, and Fault Finding Stand by or Mains is applied Protection Standby Supply starts running. All standby supply voltages become available. st-by µP resets If the protection state was left by short circuiting the Initialise I/O pins of the st-by µP: SDM pins, detection of a protection condition during - Switch reset-AVC LOW (reset state)
Page 27
Service Modes, Error Codes, and Fault Finding Q552.1L LA EN 27 Reset-system is switched HIGH by the Reset-system is switched HIGH by the AVC at the end of the bootscript AVC at the end of the bootscript AVC releases Reset-Ethernet, Reset-USB and AVC releases Reset-Ethernet, Reset-USB and Reset-DVBs when the end of the AVC boot- Reset-DVBs when the end of the AVC boot-...
Page 28
EN 28 Q552.1L LA Service Modes, Error Codes, and Fault Finding Constraints taken into account: - Display may only be started when valid LVDS output clock can be delivered by the AVC. - To have a reliable operation of the EEFL backlight, the backlight should be driven with a maximum PWM duty cycle during the first seconds.
Page 29
Service Modes, Error Codes, and Fault Finding Q552.1L LA EN 29 Semi Standby The assumption here is that a fast toggle (<2s) can only happen during ON->SEMI ->ON. In these states, the AVC is still active and can provide the 2s delay. If the transition ON->SEMI- >STBY->SEMI->ON can be made in less than 2s, Wait until previous on-state is left more than 2 seconds ago.
Page 30
EN 30 Q552.1L LA Service Modes, Error Codes, and Fault Finding Active Mute all sound outputs via softmute Wait 100ms Set main amplifier mute (I/O: audio-mute) Force ext audio outputs to ground (I/O: audio reset) And wait 5ms switch off Ambilight Wait until Ambilight has faded out: Output power Observer should be zero Switch off POK line...
Page 31
Service Modes, Error Codes, and Fault Finding Q552.1L LA EN 31 Semi Stand by If ambientlight functionality was used in semi-standby (lampadaire mode), switch off ambient light (see CHS ambilight) *) If this is not performed and the set is Delay transition until ramping down of ambient light is switched to standby when the switch off of finished.
Page 32
Introduction The error code buffer contains all detected errors since the last ComPair (Computer Aided Repair) is a Service tool for Philips time the buffer was erased. The buffer is written from left to Consumer Electronics products. and offers the following: right, new errors are logged at the left side, and all other errors 1.
Page 33
Service Modes, Error Codes, and Fault Finding Q552.1L LA EN 33 • Via the blinking LED procedure. See section 5.5.3 How to content, as this history can give significant information). This to Clear the Error Buffer. ensure that old error codes are no longer present. •...
Page 34
EN 34 Q552.1L LA Service Modes, Error Codes, and Fault Finding LAYER 2 error = 28 will be logged and displayed via the 2. Two short blinks of 250 ms followed by a pause of 3 s blinking LED procedure if SDM is switched on. 3.
Page 35
Service Modes, Error Codes, and Fault Finding Q552.1L LA EN 35 Fault Finding and Repair Tips • +5V-TUN supply voltage (5V nominal) for tuner and IF amplifier. Read also section “5.5 Error Codes, 5.5.4 Error Buffer, Extra +3V3-STANDY (3V3 nominal) is the permanent voltage, Info”.
Page 36
EN 36 Q552.1L LA Service Modes, Error Codes, and Fault Finding 900 kHz for 12 V to 3.3 V and 12 V to 5 V DC-DC UART loggings reporting fault conditions, error messages, converters. The DVB-S2 supply 24 V to 5 V and 24 V to +V error codes, fatal errors: LNB DC-DC converters operates at 300 kHz while for 5 V •...
Page 37
Before starting: - prepare a USB memory stick with the latest software - download the latest Main Software (Fus) from www.p4c.philips.com - unzip this file - create a folder ”upgrades” in the root of a USB stick (size > 50 MB) and save the autorun.upg file in this "upgrades"...
Page 38
EN 38 Q552.1L LA Service Modes, Error Codes, and Fault Finding Set is st art in g u p in F act o ry m o d e Set is starting up in F actory m ode? Noisy picture with bands/lines is visible and the An “F”...
Page 39
6.5 Reset of Repaired SSB). 2. Press the “OK” button on a Philips TV remote control or a 4. Check in CSM if the CI + key, MAC address.. are valid. Philips DVD RC-6 remote control (it is also possible to use For the correct order number of a new SSB, always refer to the a TV remote in “DVD”...
Page 40
How to start the “back-up software upgrade application” manually: 1. Disconnect the TV from the Mains/AC Power. 2. Press the “CURSOR DOWN”-button on a Philips TV remote control while reconnecting the TV to the Mains/AC Power. 3. The back-up software upgrade application will start.
Alignments Q552.1L LA EN 41 6. Alignments Index of this chapter: For the next alignments, supply the following test signals via a 6.1 General Alignment Conditions video generator to the RF input: 6.2 Hardware Alignments • EU/AP-PAL models: a PAL B/G TV-signal with a signal 6.3 Software Alignments strength of at least 1 mV and a frequency of 475.25 MHz 6.4 Option Settings...
Page 42
EN 42 Q552.1L LA Alignments Table 6-3 White D alignment values - LED - Minolta CS-200 Matrix # Matrix 4 0.95 Value Cool (11000K) Normal (9000K) Warm (6500K) Matrix 5 0.95 0.276 0.287 0.313 Matrix 6 0.95 0.282 0.296 0.329 Matrix 7 0.97 0.95...
Page 43
Alignments Q552.1L LA EN 43 See Table 6-11 SAM mode overview. 6.5.1 SSB identification 6.4.3 (Service) Options Whenever ordering a new SSB, it should be noted that the correct ordering number (12nc) of a SSB is located on a sticker on the SSB.
Page 44
EN 44 Q552.1L LA Alignments Total Overview SAM modes Table 6-11 SAM mode overview Main Menu Sub-menu 1 Sub-menu 2 Sub-menu 3 Description Hardware Info A. SW version e.g. “Q5521_0.33.0.0 Display TV & Stand-by SW version and CTN serial number B.
Page 45
Alignments Q552.1L LA EN 45 Main Menu Sub-menu 1 Sub-menu 2 Sub-menu 3 Description Options Digital broadcast Off/On Select DVB On/Off DVB - T installation Off/On or Country dependent Select DVB T installation On/Off or by country DVB - T light Off/On Select DVB T light On/Off DVB - C...
Page 46
EN 46 Q552.1L LA Alignments Main Menu Sub-menu 1 Sub-menu 2 Sub-menu 3 Description Option numbers Group 1 e.g. “00008.01793.15421.08192” The first line (group 1) indicates hardware options 1 to 4 Group 2 e.g. “44013.34315.00000.00000” The second line (group 2) indicates software options 5 to 8 Store Store after changing...
Circuit Descriptions Q552.1L LA EN 47 7. Circuit Descriptions Index of this chapter: Introduction 7.1 Introduction 7.2 Power Architecture The Q552.1L LA chassis is part of the TV550 platform and 7.3 DC/DC Converters comes with the following stylings: “van Gogh” (series 7.4 Front-End Analogue and DVB-T, DVB-C;...
Page 48
EN 48 Q552.1L LA Circuit Descriptions 18770_245_100203.eps 100219 Figure 7-2 Architecture of TV550 platform - TCON integrated on SSB (xxPFL5xxx & xxPFL6xxx) 7.1.3 SSB Cell Layout Class- RJ45 Tuner HDMI 1.3 HDMI 1.3 HDMI 1.3 18990_200_100401.eps 100401 Figure 7-3 SSB layout cells (top view) TCON integrated in display (xxPFL8xxx) back to 2010-Dec-29 div.
Page 49
Circuit Descriptions Q552.1L LA EN 49 DVB-S TCON Tuner HDMI 1.3 HDMI 1.3 HDMI 1.3 18990_201_100401.eps 100401 Figure 7-4 SSB layout cells (top view) TCON integrated on SSB (xxPFL5xxx & xxPFL6xxx) back to 2010-Dec-29 div. table...
Page 50
7.2.2 Diversity specifications! This part is available in the regular market. Consult the Philips Service web portal for the order codes of the The diversity in power supply units is mainly determined by the boards. diversity in displays.
Page 51
Circuit Descriptions Q552.1L LA EN 51 7.2.3 Connector overview • the LNBH23Q (item no. 7T50) sends a feedback signal via the V0-CNTRL line • the switching frequency of the +5V-DVBS to +1-DVBS Table 7-1 Connector overview switched mode converter is 900 kHz (item no. 7T00) •...
Page 52
EN 52 Q552.1L LA Circuit Descriptions HDMI • Embedded HDMI HDCP keys • Extended color gamut and color booster • Integrated USB2.0 host controller In this platform, the Silicon Image Sil9x87 HDMI multiplexer is • Improved MPEG artefact reduction compared with implemented.
Page 53
Circuit Descriptions Q552.1L LA EN 53 PNX85500x MEMORY CONTROLLER TS input MPEG SYSTEM CI/CA LVDS for TS out/in for PRIMARY PROCESSOR flat panel display PCMCIA VIDEO LVDS (single, dual or OUTPUT quad channel) DVB-T/C channel decoder AV-PIP SUB-PICTURE VIDEO CVBS, Y/C, 3D COMB DECODER SECONDARY...
Page 54
EN 54 Q552.1L LA Circuit Descriptions Back-End The following backlight types can be distinguished: • CCFL/EEFL backlight; applicable to the xxPFL54xx sets • LED backlight: - side-view (edge) LED without scanning: PSL power board; applicable to xxPFL76xx sets - side-view (edge) LED with scanning: PSLS power board; not applicable to this chassis - direct-view LED with 0D-dimming: PSL power board;...
Page 55
Circuit Descriptions Q552.1L LA EN 55 +3V3 7B20-1 74LVC2G17 3B01-2 3B30-1 PWM-CLOCK-BUF PWM-CLOCK × 100R 220R × × 7B20-2 × × 74LVC2G17 +3V3 3B01-1 3B30-4 × SPI-CLOCK-BUF SPI-CLOCK 100R 220R 18770_214_100126.eps 100126 Figure 7-15 Ambilight buffer 18770_210_100126.eps The temperature sensor is built around item no. 7B30 (diagram 100126 AL1A) and indicates overtemperature of the board.
Page 57
Circuit Descriptions Q552.1L LA EN 57 EEPROM LVDS (10 bit) Timing Mini - LVDS Controller (TCON) Control Signals Gamma Reference Source Drive IC Voltage +3.3 V +1.8 V +16 V TFT – LCD Panel +12 V Power Block (+28 V) (-6 V) M ain P latform T C O N...
Page 58
C communication). For Sharp - TCONs, the data can be flashed with a “SPI Programmer” (via SPI communication). This device has to be ordered separately via Philips. 7.9.2 TCON Alignment The purpose of TCON alignment is to obtain equal voltages for both positive and negative LC polarity.
IC Data Sheets Q552.1L LA EN 59 8. IC Data Sheets This chapter shows the internal block diagrams and pin electrical diagrams (with the exception of “memory” and “logic” configurations of ICs that are drawn as “black boxes” in the ICs).
Page 60
EN 60 Q552.1L LA IC Data Sheets Diagram Temp Sensor + Headphone B01J, LM75BDP (IC 7FD1) Block diagram LM75B BIAS POINTER CONFIGURATION REFERENCE REGISTER REGISTER TEMPERATURE COUNTER BAND GAP REGISTER 11-BIT TEMP SENSOR SIGMA-DELTA A-to-D TIMER REGISTER CONVERTER OSCILLATOR COMPARATOR/ THYST INTERRUPT REGISTER...
Page 61
IC Data Sheets Q552.1L LA EN 61 Diagram PNX NandFlash - Conditional Access B02A, PNX85500 (IC7S00) Block diagram PNX8550x MEMORY CONTROLLER TS input MPEG SYSTEM CI/CA LVDS for PRIMARY TS out/in for PROCESSOR flat panel display PCMCIA VIDEO LVDS (single, dual or OUTPUT quad channel) DVB-T/C...
Page 62
EN 62 Q552.1L LA IC Data Sheets Diagram Audio B03A, TPA3120D2PWP (IC7D10) Block diagram TPA3120D2 0.22 F 22 H 470 F ROUT 0.68 F PGNDR 0.68 F PGNDL LOUT BYPASS 22 H 470 F AGND 0.22 F PVCCL AVCC PVCCR VCLAMP Shutdown Control...
Page 63
IC Data Sheets Q552.1L LA EN 63 Diagram DC/DC B03B, TPS53126PW (IC7U03) Block diagram Pinning information VBST1 DRVH1 DRVL1 PGND1 VFB1 TRIP1 VREG5 TEST1 V5FILT TEST2 TRIP2 VFB2 PGND2 DRVL2 DRVH2 VBST2 18250_300_090319.eps 100402 Figure 8-5 Internal block diagram and pin configuration back to 2010-Dec-29 div.
Page 64
EN 64 Q552.1L LA IC Data Sheets Diagram DC/DC B03E, ST1S10PH (IC 7UD0) Block diagram Pinning information DFN8 (4 × 4) PowerSO-8 I_18010_083.eps 100402 Figure 8-6 Internal block diagram and pin configuration back to 2010-Dec-29 div. table...
Page 65
IC Data Sheets Q552.1L LA EN 65 Diagram DC/DC B03E, LD1117DT25 (IC 7UD2) Block diagram LD1117DT Pinning information DPAK F_15710_166.eps 100402 Figure 8-7 Internal block diagram and pin configuration back to 2010-Dec-29 div. table...
Page 66
EN 66 Q552.1L LA IC Data Sheets Diagram Ethernet + Service B04C, LAN8710A-EZKH (IC 7E10) Block diagram MODE0 HP Auto-MDIX Auto- 10M Tx MODE1 MODE Control Negotiation Logic Transmitter TXP / TXN MODE2 Reset Transmit Section RXP / RXN nRST Control 100M Tx 100M...
Page 67
IC Data Sheets Q552.1L LA EN 67 Diagram HDMI B04D, SII9287B (IC 7EC1) Block diagram Pinning information 18770_303_100217.eps 100217 Figure 8-9 Internal block diagram and pin configuration back to 2010-Dec-29 div. table...
Page 68
EN 68 Q552.1L LA IC Data Sheets 8.10 Diagram Headphone B04E, TPA6111A2DGN (IC 7EE1) Block diagram IN 1− − BYPASS IN 2− − SHUTDOWN Bias Control Pinning information D OR DGN PACKAGE (TOP VIEW) IN1− BYPASS IN2− SHUTDOWN 18770_309_100217.eps 100217 Figure 8-10 Internal block diagram and pin configuration back to 2010-Dec-29...
Block Diagrams Q552.1L LA EN 72 9-4 Block Diagram Video VIDEO B01K B06B B14A B14E TUNER BRAZIL PNX85500 VIDEO OUT - LVDS TCON CONTROL (SHARP) MINI LVDS (SHARP) 1KA1 7S00 B14C P GAMMA & PNX85507EB 1G50 7KAA 7FE0 VOM & FLASH UPD809900F TC90517FG B02A...
Circuit Diagrams and PWB Layouts Q552.1L LA EN 77 10. Circuit Diagrams and PWB Layouts 10-1 AL1 820400089786 AmbiLight Common LiteOn LED Common LiteOn 15 LED Common AL1A AL1A 1M83 C1 +3V3 2B00 E8 2B11 2B01 F8 2B02 E9 100n 2B03 I14 FH12-25S-0.5SH(55) 7B26-1...
Page 78
Circuit Diagrams and PWB Layouts Q552.1L LA EN 78 LiteOn LED Common 2 LiteOn 15 LED Common 2 AL1B AL1B 2B50 C11 3B50 B7 +24V 3B51 B7 7B50-1 3B52 B7 BC847BS(COL) 3B53-1 B7 3B53-2 C7 3B53-3 C7 FB70 3B53-4 C7 PWM-B2 3B50 +24V...
Circuit Diagrams and PWB Layouts Q552.1L LA EN 79 10-2 AL3 820400089712 21 LED LiteOn 21 LED LiteOn 21 LED LiteOn AL3A AL3A 1M84 7203 7204 7205 LTW-008RGB LTW-008RGB LTW-008RGB SPI-CLOCK-BUF SPI-DATA-OUT2 Blue BLUE BLUE BLUE SPI-DATA-RETURN +24V GREEN GREEN GREEN Green PWM-CLOCK-BUF...
Page 80
Circuit Diagrams and PWB Layouts Q552.1L LA EN 80 21 LED LiteOn 21 LED LiteOn AL3B AL3B 2E10 D13 2F10 H13 3E02-1 C2 3E02-2 C2 3E02-3 B2 3E02-4 B2 3E05-3 D2 3E05-4 D2 3E10 B13 +24V 3E11 C13 3E12 C13 7E01-1 3E13-1 C13 BC847BS(COL)
Page 81
Circuit Diagrams and PWB Layouts Q552.1L LA EN 81 21 LED LiteOn 21 LED LiteOn AL3C AL3C 2D04-1 C7 2D04-2 C7 2D04-3 C8 2D04-4 C7 2D10 G14 2D11 B9 3D00-1 B7 3D00-2 C7 +3V3 3D00-3 C7 2D11 3D00-4 B7 100n 3D02-1 E2 7D26-1 3D02-2 E2...
Page 115
Circuit Diagrams and PWB Layouts Q552.1L LA EN 115 PNX Digital Video In PNX Digital Video In B02C B02C 2S2E F5 3S0W E5 7S00-6 D6 IS01 E6 IS10 E7 7S00-6 PNX85500 HDMI_DV HDMIA-RX2+ RX0_A HDMIA-RX2- HDMIA-RX1+ HDMIA-RX1- RX1_A DDCA-SCL DDC_A DDCA-SDA HDMIA-RX0+ IS10...
Circuit Diagrams and PWB Layouts Q552.1L LA EN 153 10-20 SRP List Explanation Example 1.1. Introduction Net Name Diagram +12V B03B (1 ×) +12V B03C (1 ×) SRP (Service Reference Protocol) is a software tool that creates a list with all references to signal lines. The list contains +12VD B03C (1 ×) +12VD...