Miele TWL 780 WP Operating Instructions Manual
Heat-pump dryer
Hide thumbs
Also See for TWL 780 WP:
- Manual (15 pages) ,
- Operating instructions manual (108 pages) ,
- Operating instructions manual (96 pages)
Chapters
Table of Contents
Related Manuals for Miele TWL 780 WP
Summary of Contents for Miele TWL 780 WP
- Page 1 Operating instructions Heat-pump dryer To avoid the risk of accidents or damage to the appliance it is essen- tial to read these instructions before it is installed and used for the first time. en-GB M.-Nr. 12 219 080...
-
Page 2: Table Of Contents
Examples on how to operate the appliance ............21 Before using for the first time ................22 Installation ......................22 Downtime after installation................22 Information about networking ................22 Miele@home ....................22 Wash2Dry ....................23 Energy saving tips ..................... 26 Energy saving tips ....................26 Feedback......................27 1. - Page 3 Contents 5. Starting a programme ................... 38 Starting the programme ..................38 6. End of programme - unload the drum ............39 End of programme....................39 Unloading the drum..................... 39 Programme chart ....................40 Programmes on the control panel ............... 40 Further programmes....................
- Page 4 Contents Problem solving guide ..................64 Fault messages shown in the display when a programme is cancelled ..... 64 Messages in the display..................66 Unsatisfactory drying results................67 The drying cycle duration is very long..............68 General problems with the tumble dryer ............. 69 Replacing the plinth filter..................
- Page 5 Buttons active ....................105 Buttons inactive....................105 Disp. switch-off stat.................... 106 Memory ....................... 106 Anti-crease ......................106 Programme info ....................107 Miele@home ......................107 Remote control....................108 SmartGrid ......................108 Wash2Dry ......................109 RemoteUpdate ....................109 Running a RemoteUpdate................109 Factory default.....................
-
Page 6: Caring For The Environment
The packaging with Miele, free of charge. By law, you material used is selected from materials are solely responsible for deleting any which are environmentally friendly for personal data from the old appliance disposal and can generally be recycled. -
Page 7: Warnings And Safety Instructions
Miele cannot be held liable for damage caused by non-compliance with these instructions. Keep these operating instructions in a safe place and pass them... - Page 8 Any other applications may be dangerous. Miele cannot be held li- able for damage resulting from incorrect or improper use or opera- tion.
- Page 9 It is essential that this standard safety re- quirement is met. If in any doubt, please have the household wiring system tested by a qualified electrician. Miele cannot be held liable for the consequences of an inadequate earthing system (e.g. electric shock).
- Page 10 Warnings and safety instructions Unauthorised repairs could result in unforeseen dangers for the user, for which Miele cannot accept liability. Repairs should only be undertaken by a Miele approved service technician, otherwise any subsequent damage will not be covered by the warranty.
- Page 11 This special lamp must only be used for the purpose it is intended for. It is not suitable for room lighting. Replacement lamps may only be fitted by a Miele authorised person or the Miele Service Department.
- Page 12 - Disconnect the tumble dryer from the electrical supply. - Air the room where the tumble dryer is located. - Contact the Miele Customer Service Department. Risk of fire and explosion due to damage to the tumble dryer. The refrigerant is flammable and explosive if it leaks.
- Page 13 Warnings and safety instructions Warning: Do not switch the dryer off before the drying pro- gramme has finished. If this is done, the laundry must be hung up or spread out to cool it down. Fabric conditioner and similar products must be used according to the instructions on the manufacturer's packaging.
- Page 14 Warnings and safety instructions To prevent the risk of fire, textiles that have not been cleaned thor- oughly or are still soiled with deposits of any kind must not be dried in this tumble dryer. This applies in particular to textiles that - have not been washed.
- Page 15 Warnings and safety instructions To prevent the risk of fire, these textiles must not be tumble dried: - textiles that have been cleaned using chemicals (e.g. professional dry-cleaning agents) - textiles which contain a large proportion of rubber, foam rubber or rubber-like materials.
- Page 16 Warnings and safety instructions Always close the door after use. This way you will avoid the danger of: - Children climbing onto or into the dryer or hiding things in it. - Pets or other small animals climbing into it. ...
- Page 17 Warnings and safety instructions Using a fragrance flacon (optional accessory) Only use genuine Miele original fragrance flacons. The fragrance flacon must be stored in its packaging so please make sure you retain this. Caution. The fragrance can leak out of the flacon. Make sure that...
- Page 18 If you order a plinth for this tumble dryer (available from Miele as an optional accessory - depending on country), make sure it is the correct one.
-
Page 19: Operating The Tumble Dryer
Operating the tumble dryer Control panel a Display e OK sensor The following values are shown on The OK sensor is used for confirm- the display and/or selected from it: ing selected values. 1. - Page 20 Operating the tumble dryer h Start/Add laundry sensor control k Programme selector Touching the Start/Add laun- For selecting programmes and for dry sensor control starts a pro- switching the appliance off. The gramme. The current programme tumble dryer is switched on by se- can be interrupted to add laundry.
-
Page 21: Display
Operating the tumble dryer Display Identifying the selected option The basic display shows the following for a drying level programme: Normal 0:55 An activated option in a list will have a tick next to it. ... -
Page 22: Before Using For The First Time
- a WiFi network formation provided under “Installa- tion”. - the Miele app - a Miele user account. The user ac- Removing the protective foil and count can be created via the Miele stickers app. -
Page 23: Wash2Dry
Cloud. The tumble dryer automatically sets a Miele@home availability drying programme tailored to the laun- The ability to use the Miele app de- dry based on the transferred pro- pends on the availability of the gramme data. Miele@home service in your country. - Page 24 Follow the prompts on the display. Connecting via Miele app The following appears in the display: Waiting for App Now switch to the Miele app. Carry out the rest of the steps for the registration process in the Miele app.
- Page 25 Before using for the first time You will require a WPS-compatible router for the connec- Connect via WPS tion type. Activate the WPS function on your router within 2 minutes. If the connection is successful, the fol- lowing will appear in the display: ...
-
Page 26: Energy Saving Tips
Energy saving tips - If possible, make use of time-vari- Energy saving tips able, low-cost electricity tariffs. Ask This dryer with heat-pump technology your energy supplier for information. is designed for energy-saving drying Your tumble dryer's delay start func- cycles. However, you can save a little tion will be useful as you can select more energy with the following meas- when during the next 24 hours you... -
Page 27: Feedback
Energy saving tips 2. Viewing the actual consumption Feedback The actual energy consumption can be You can view information about the en- viewed during the programme or at the ergy consumption of your tumble dryer end of the programme. with the sensor. ... -
Page 28: Notes On Correct Laundry Care
1. Notes on correct laundry care Points to note regarding Risk of fire due to incorrect use washed laundry and operation. The laundry can burn and destroy - When washing very heavily soiled the dryer and the surroundings. items ensure that you use sufficient See “Warning and Safety”... -
Page 29: Drying
1. Notes on correct laundry care Care symbols Drying Tip: See the “Programme chart”, which Drying contains everything you need to know Temperature about programmes and load sizes. Normal or higher - Always observe the maximum recom- mended load size for each pro- ... -
Page 30: Load The Tumble Dryer
2. Load the tumble dryer Checking the FragranceDos socket Loading the laundry If you are not using a fragrance flacon, Preventing damage to fabrics. check that the 2 FragranceDos sockets Before loading the dryer, read “1. are closed. Notes on correct laundry care”. The “Fragrance flacon”... -
Page 31: Selecting A Programme
3. Selecting a programme Switching on the tumble dryer Selecting a programme The dryer is switched on by selecting a There are 4 possible ways to select a programme, and switched off by turning programme. the programme selector to the posi- 1. - Page 32 3. Selecting a programme 2. Selecting further programmes/ 3. Selecting MobileStart Tip: In this case, the appliance is oper- ated via the Miele app. In order to use MobileStart , the tumble dryer must be logged on to the WiFi network and Remote control must be switched on.
- Page 33 3. Selecting a programme 4. Selecting Wash2Dry Once the wash cycle has ended, place the clean laundry in the tumble dryer. Turn the programme selector to Wash2Dry . Please wait lights up in the display of the tumble dryer while the wash pro- gramme is running.
-
Page 34: Selecting Programme Settings
4. Selecting programme settings - At the start of the temperature hold- Selecting the drying level ing time, the remaining programme Check the “Programme chart” to see running time is extended by 85 which programme you can select a dry- minutes to produce a hygienic drying ing level for and which drying level result. -
Page 35: Selecting The Running Time For Time Programmes
4. Selecting programme settings Selecting the running time for time programmes The programme running time can be selected in 10-minute increments. Programmes: Cool air: 20 min – 1:00 h Warm air: 20 min – 2:00 h Basket programme: 40 min – 2:30 h 2:00 ... -
Page 36: Delay Start/Smartstart
4. Selecting programme settings Delay start/SmartStart Cancelling delay start The selected delay start time can be Delay start cancelled before the programme starts. With the delay start function, you can Touch the sensor. choose when you want the pro- The selected delay start time will ap- gramme to start. - Page 37 4. Selecting programme settings SmartStart The following will appear in the display: The SmartStart function lets you SmartStart define a time period during which your tumble dryer will start automatically. The appliance will start on receipt of a signal, e.g.
-
Page 38: Starting A Programme
5. Starting a programme The drying level reached for the selec- Starting the programme ted drying level programme will light up Touch the flashing Start/Add laundry in the display. sensor control. You can view the selected drying level or time again: The Start/Add laundry sensor control will light up and Drying appears in the ... -
Page 39: End Of Programme - Unload The Drum
6. End of programme - unload the drum Turn the programme selector to the End of programme position. The programme is finished when Finish/ Remove the fluff from the 2 fluff filters Anti-crease Finish/Cooling down Finished in the door opening: see “Cleaning appears in the display. -
Page 40: Programme Chart
Programme chart All weights marked with * are based on the weight of dry laundry. Programmes on the control panel Cottons max. 9 kg* Use for Cotton items such as those described under Cottons Normal with normal residual moisture. Note - Items are dried to a Normal level only in this programme. - The Cottons ... -
Page 41: Cottons
Programme chart Cottons max. 9 kg* HygieneDry Use for - Cottons and linen fabric which will be in direct contact with the skin, e.g. underwear, baby clothes, bed linen, towelling. - Other hard-wearing fabrics with special hygiene requirements. - Use for special hygiene requirements. - Reduce to half the maximum load amount. -
Page 42: Delicates
Normal +, Normal, Hand iron , Hand iron Use for Shirts and blouses MobileStart The Miele app is used for selecting programmes and operating the appliance. Wash2Dry The programme is selected automatically in conjunction with the programme se- lection on the connected washing machine. -
Page 43: Steam Care
Programme chart Steam care max. 1 kg* Normal, Hand iron Use for - All items made of cotton or linen - For minimum iron items made of cotton, mixed or synthetic fibre. For example, cotton trousers, anoraks and shirts. - For dampening fabrics before ironing - For smoothing fabrics that are creased - Select Hand iron if the items are to be ironed after drying. -
Page 44: Further Programmes
Programme chart Further programmes Warm air max. 9 kg* Use for - Multi-layered fabrics whose layers have different drying character- istics, e.g. jackets, pillows, sleeping bags and other bulky items. - For drying individual items, e.g. bath towels, bathing costumes and tea towels. Do not select the longest drying time to start with. -
Page 45: Automatic Plus
Basket programme Max. load for basket 3.5 kg Note - This programme may only be used with the Miele tumble dryer basket TRK 555 (optional accessory) fitted. - Always follow the operating instructions for the tumble dryer bas- ket. -
Page 46: Silks Handcare
Programme chart Silks handcare max. 1 kg* Use for Silk garments which are suitable for drying in the tumble dryer, e.g. blouses and shirts Note - This programme reduces creasing. Items are not dried completely by this programme. - Remove the garments as soon as the programme has finished. Denim max. 3 kg* Normal +, Normal, Hand iron , Hand iron ... -
Page 47: Extras
Extras DryCare 40 The drying programmes can be aug- mented with various extra options. This option dries fabrics gently at very low temperature. Certain combinations of extra options are not possible. It can be used for all fabrics that are free of wool and are washable at tem- peratures of 40 °C and above. -
Page 48: Powerfresh
Extras See “Condensed water container – PowerFresh Filling the condensed water container”. This option can be used to freshen up clothing that is clean and dry by using Buzzer steam. A buzzer sounds to let you know the The fabrics are moistened automatic- programme has finished. -
Page 49: Drying Programme Overview - Extras
Extras Drying programme overview - Extras DryFresh DryCare 40 PowerFresh Buzzer Cottons – – – Cottons Minimum iron Delicates – – Woollens hand- – – – care Shirts Bed linen – – – Steam care – – – Pre-ironing –... -
Page 50: Changing The Programme Sequence
Changing the programme sequence Changing a programme once it Adding or removing laundry has started You have forgotten something but the programme is already running. It is no longer possible to change the selected programme. This is to prevent Touch the Start/Add laundry sensor the operation of the machine being control. -
Page 51: Condensed Water Container
Condensed water container Emptying the condensed water container The condensed water is collected in the condensed water container. Empty the condensed water container after every drying programme. When the maximum level in the con- densed water container is reached, the following message will light up in the display: Empty container. -
Page 52: Filling The Condensed Water Container
Condensed water container Filling the condensed water container When certain programmes are being used, condensed water generated dur- ing drying is recycled and sprayed into the drum via a spray nozzle. The condensed water container must therefore be filled to at least the ―min―... -
Page 53: Fragrance Flacon
Fragrance flacon FragranceDos Removing the protective seal from the fragrance flacon Fragrance flacons (optional accessor- ies) can be used to give your laundry a Only hold the fragrance flacon as il- pleasant scent. lustrated. Do not hold it at an angle or tip it, as the fragrance will leak out This dryer has 2 places for inserting of it. -
Page 54: Inserting The Fragrance Flacon
Fragrance flacon Inserting the fragrance flacon Open the door of the tumble dryer. The fragrance flacon is inserted in the upper fluff filter. They can be fitted on the left and the right hand side next the opener. Insert the fragrance flacon into the socket as far as it will go. -
Page 55: Opening The Fragrance Flacon
Fragrance flacon grance will also be noticeable in the room air during the process. The Cool Air programme will not generally apply fragrance. Closing the fragrance flacon After drying, the fragrance flacon should be closed to prevent the fragrance from escaping needlessly. -
Page 56: Removing/Replacing The Fragrance Flacon
- Always store in a cool, dry place Fragrance flacons are available to or- away from direct sunlight. der from Miele or online at www.miele- - When purchasing new fragrance flac- shop.com. ons, only remove the protective seal... -
Page 57: Cleaning And Care
Cleaning and care Removing visible fluff Fluff filters Tip: You can also use a vacuum cleaner This tumble dryer has 2 fluff filters in the so that you can remove the fluff without loading area of the door. Both fluff fil- touching it. -
Page 58: Cleaning The Fluff Filters And Air Flow Openings Thoroughly
Cleaning and care Remove the fluff from the filter sur- Turn the yellow dial on the lower fluff face of all the fluff filters and the per- filter in the direction of the arrow (until forated laundry deflector. it reaches the stop position). -
Page 59: Cleaning The Fluff Filters With Water
Cleaning and care Cleaning the fluff filters with water Wipe the smooth plastic surfaces of the fluff filters with a damp cloth to clean them. Flush the filters through under warm running water. Shake the fluff filters thoroughly and then dry them carefully. -
Page 60: Cleaning The Plinth Filter
Cleaning and care Cleaning the plinth filter Clean the plinth filter when the pro- gramme running time is longer than usual or if the following message lights up in the display: Clean the plinth filter. See To clear the message, confirm with Removing the plinth filter ... - Page 61 Cleaning and care If a drying programme is interrupted with a fault message after the clean plinth filter has been fitted, the plinth filter was too wet when it was fitted. Carefully squeeze the water out of the plinth filter again. Leave the plinth filter to air-dry.
- Page 62 Cleaning and care Push the plinth filter in completely. This will push in the right-hand guide pin at the same time.
-
Page 63: Cleaning The Plinth Filter Access Panel
Cleaning and care Cleaning the plinth filter access panel Cleaning the dryer Disconnect the tumble dryer from the electrical supply. Damage due to the use of un- suitable care products. Unsuitable care products could dam- age plastic surfaces and other parts. Do not use any solvents, abrasive cleaners, glass cleaners, or all-pur- pose cleaners. -
Page 64: Problem Solving Guide
You can save time and money in many cases, as you do not need to call the Miele Customer Service Department. Information to help you rectify faults yourself can be found at www.miele.com/ser- vice. The following tables are designed to help you to find the cause of a malfunction or a fault and to resolve it. - Page 65 Problem solving guide Message Cause and remedy The system has been clogged by fluff or detergent Clean the plinth filter. residue. See To deactivate the message, turn the programme selector to the position. Clean the fluff filters and the plinth filter. –...
-
Page 66: Messages In The Display
Problem solving guide Messages in the display Message Cause and remedy Access via a code has been activated. Enter the code and confirm the entry. Deactivate the code if you do not wish this message to ap- pear in the display the next time the appliance is switched on. -
Page 67: Unsatisfactory Drying Results
Problem solving guide Unsatisfactory drying results Problem Cause and remedy The DryCare 40 Extra is The room where the tumble dryer is located is too not drying the laundry warm. This has caused the DryCare process to finish sufficiently. prematurely. Ventilate the room thoroughly. ... -
Page 68: The Drying Cycle Duration Is Very Long
Problem solving guide The drying cycle duration is very long Problem Cause and remedy The drying process The room where the tumble dryer is located is too goes on too long or warm. even switches off.* Ventilate the room thoroughly. Detergent residues, hair and fine fluff can clog the fil- ters. -
Page 69: General Problems With The Tumble Dryer
Problem solving guide General problems with the tumble dryer Problem Cause and remedy You can hear buzzing or The compressor (heat pump) is operating. Or you humming operating have selected a programme which sprays con- noises. densed water into the drum. ... - Page 70 The drum lighting is designed to last a long time and should not normally need to be replaced. If you have tried everything but the drum lighting still does not come on, contact the Miele Cus- tomer Service Department. The spray jet for spray-...
-
Page 71: Replacing The Plinth Filter
Problem solving guide Deformations Replacing the plinth filter The heat exchanger can clog up. Replace the plinth filter immediately if you see the following signs of wear before or after cleaning (optional ac- cessory). Poor fit Deformations indicate that the filter has become blocked and worn by continu- ous use. - Page 72 Problem solving guide Cracks, tears, indentations White residues or residues of other col- ours These residues arise from laundry fibres and traces of detergent components. They can be found on the front and side edges of the plinth filter. In extreme cases, they can form stubborn crust.
-
Page 73: Reactivating The Plinth Filter
Problem solving guide Reactivating the plinth filter Checking the heat exchanger You can reactivate one or more soiled Risk of injury from sharp cooling plinth filters in a washing machine. You fins. will then be able to use the plinth filter You could cut yourself. -
Page 74: Cleaning The Fluff Filter In The Condensed Water Container
Problem solving guide Cleaning the fluff filter in the condensed water container When certain programmes are being used, water is taken from the con- densed water container and sprayed into the drum. The spray jet can some- times stop working. The fluff filter in the condensed water container is clogged. -
Page 75: Replacing The Condensed Water Spray Jet
Problem solving guide Open the tumble dryer door. Replacing the condensed wa- ter spray jet The spray jet is located in the top left of the door opening. When certain programmes are being used, water is taken from the con- densed water container and sprayed into the drum. -
Page 76: Service
Contact in the event of a fault In the event of any faults which you cannot remedy yourself, please contact your Miele dealer or the Miele Customer Service Department. You can book a Miele Customer Ser- vice Department call-out online at www.miele.com/service. -
Page 77: Optional Accessories
Service Optional accessories Optional accessories for this tumble dryer are available from Miele or from your Miele dealer. You also can order these and many other useful products from the Miele online shop. Dryer basket The dryer basket is enables items which must not be subjected to mechanical action to be dried or aired. -
Page 78: Installation
*INSTALLATION* Installation Front view a Mains connection cable e Plinth filter flap b Control panel f 4 height-adjustable feet c Condensed water container g Cooling air grille d Door h Drain hose for condensed water... -
Page 79: Rear View
*INSTALLATION* Installation Rear view If the tumble dryer is being transpor- ted on its side, it must be tipped onto its left or right side. a Protruding lid for holding when mov- If the tumble dryer is being transpor- ing the appliance ted upright and you are using a hand b Drain hose for condensed water... -
Page 80: Installation
- Air the room where the tumble dryer dryer must stand perfectly level. The is located. screw feet on the tumble dryer can be - Contact the Miele Customer Service adjusted to compensate for unevenness Department. in the floor. Downtime after installation ... -
Page 81: Ventilation
*INSTALLATION* Installation Ventilation The heat pump that is essential to the operation of this tumble dryer The cool air intake at the front of the generates a great deal of heat inside tumble dryer must not be blocked or its casing. There must be a reliable covered. -
Page 82: Additional Installation Requirements
– Washer-dryer stack heat. The tumble dryer can be combined with Make sure there is adequate room a Miele washing machine in a washer- for warm air from the dryer to be dir- dryer stack. The appropriate Miele ected away. -
Page 83: External Condensed Water Outlet
*INSTALLATION* Installation Installation conditions requiring a External condensed water out- non-return valve Danger of condensed water Note back-flow. When drying is in progress, con- Water could flow back into the densed water is pumped into the con- tumble dryer or be drawn into it. densed water container through the Back-flow water could damage the drain hose which is located at the... -
Page 84: Arranging The Drain Hose
*INSTALLATION* Installation Arranging the drain hose Examples Drainage into a sink or floor gully Damage to the drain hose through incorrect handling. Use the hose holder to secure the drain hose. The drain hose can suffer damage and leak. Do not pull on the drain hose and do not stretch it or allow it to become kinked. - Page 85 *INSTALLATION* Installation Fit adapter 1 to the sink drain outlet Direct connection to a sink drain outlet using nut 2. Use the hose holder, the adapter, the The nut is usually fitted with a washer hose clips and the non-return valve which must be removed.
-
Page 86: Changing The Door Hinging
*INSTALLATION* Installation Hold the door securely and pull it for- Changing the door hinging wards: to remove the door you will You can change the door hinging on need to pull the base plate of the this tumble dryer yourself. hinge with its 2 pins out of the dryer. - Page 87 *INSTALLATION* Installation Turn the door lock through 180°. Use a T20 Torx screwdriver to remove screw on the lock catch. Press the door lock into openings Pull off the lock catch together with on the opposite side of the door lock catch cover .
- Page 88 *INSTALLATION* Installation 4. Dismantle the door hinge from the door The door hinge cover must be un- clipped from position and then re- moved. Insert the lock catch into the new cover supplied with the dryer. ...
- Page 89 *INSTALLATION* Installation 5. Change over the door hinge on the Tip: In some circumstances, the rods door can be difficult to dislodge. Moving the screwdriver with a levering action while The door hinge is secured to the door pulling at the same time may help to with 2 angled rods.
- Page 90 *INSTALLATION* Installation You now need the new door hinge cover supplied with the tumble dryer. Fit new door hinge cover and clip it into position. 6. Change the lock catch on the door You now need the new lock catch cover supplied with the dryer which you have already fitted with the lock catch.
-
Page 91: Refitting
*INSTALLATION* Installation Refitting Now that you have changed the door hinging the door will open from 7. Refit the door the opposite side. Press the rubber seal back into the grove on the door. Push the orange marker round to the other side so that you will see at ... -
Page 92: Electrical Connection
Miele product must also be maintained in isolated operation or in operation that The electrical system must comply with is not synchronised with the mains... -
Page 93: Technical Data
Technical data Height 850 mm Width 596 mm Depth 636 mm Depth with door open 1054 mm Height for building under 820 mm (+8/-2 mm) Width for building under 600 mm Depth for building under 600 mm Suitable for pushing under a worktop Suitable for stacking Weight Approx. 62 kg Drum volume 120 litres Load size... -
Page 94: Data Sheet For Household Tumble Driers
Technical data Data sheet for household tumble driers In acc. with delegated regulation (EU) No. 392/2012 MIELE Model name/identifier TWL 780 WP 9,0 kg Rated capacity Type of tumble drier (Air-vented / condenser) - / ● Energy efficiency class A+++ (most efficient) to D (least efficient) -
Page 95: Data Sheet For Household Tumble Driers
If the household tumble drier is a condenser tumble drier. For the standard cotton programme at full load. Data sheet for household tumble driers In acc. with delegated regulation (EU) No. 392/2012 MIELE Model name/identifier TSL 783 WP 9,0 kg Rated capacity - / ●... -
Page 96: Data Sheet For Household Tumble Driers
If the household tumble drier is a condenser tumble drier. For the standard cotton programme at full load. Data sheet for household tumble driers In acc. with delegated regulation (EU) No. 392/2012 MIELE Model name/identifier TWL 700-80 CH 9,0 kg Rated capacity - / ●... -
Page 97: Data Sheet For Household Tumble Driers
If the household tumble drier is a condenser tumble drier. For the standard cotton programme at full load. Data sheet for household tumble driers In acc. with delegated regulation (EU) No. 392/2012 MIELE Model name/identifier TSL 700-83 CH 9,0 kg... - Page 98 Technical data Programme time of the 'standard cotton programme' Weighted programme time 141 min Programme time at full load 184 min Programme time at partial load 108 min Condensation efficiency class A (most efficient) to G (least efficient) Weighted condensation efficiency for the 'standard cotton programme' at 94 % full and partial load Average condensation efficiency of the 'standard cotton programme' at full...
-
Page 99: Eu Conformity Declaration
UK Conformity declaration Miele hereby declares that this heat-pump tumble dryer complies with UK Radio Equipment Regulations 2017, as amended. The complete text of the UK declaration of conformity is available from one of the following internet addresses: - Products, Download from www.miele.co.uk... -
Page 100: Consumption Data
Consumption data Final spin speed in Residual Energy Pro- Load size washing machine mois- gramme ture running time 1000 1.55 Cottons 1000 0.84 Cottons Normal 1200 1.40 1400 1.30 1600 1.15 Cottons Hand iron 1000 1.14 1200 1.00 1400 0.95 1600 0.80 Minimum iron Normal... -
Page 101: Settings
Settings Selecting settings Accessing the settings menu Touch the or sensor until the You can alter the tumble dryer's elec- setting you want appears in the dis- tronics to suit changing requirements play. with the settings. The settings can be altered at any - The ... -
Page 102: Language
Settings Language Cooling down temp. The display can be set to appear in The laundry will be cooled down auto- one of several different languages. matically before the end of the pro- gramme. The automatic cooling-down The flag after the word Language phase which takes place before the (Sprache in German) acts as a guide in end of a programme can be set at a... -
Page 103: Keypad Tone
Settings Keypad tone Airways indicator Each touch of a sensor is confirmed Fluff should be removed after drying. with an audible tone. In addition, this indicator will remind you to clean the filters when a certain Selection amount of fluff has collected in them: ... -
Page 104: Conductivity
Settings Conductivity Consumption This setting is only relevant for regions You can display the total consump- with very soft water. tion. Selection Very soft water can result in unsatis- factory drying results. Previous programme You should only select this setting if Displays energy consumption in the the water used for washing the laun- last programme run... -
Page 105: Code
Make a note of your new code. If Buttons inactive you forget the code, the dryer will need to be unlocked by Miele Tech- Controls the brightness of the sensor nical Service. controls that can be activated. - (dark) - ... -
Page 106: Disp. Switch-Off Stat
Settings Disp. switch-off stat. Memory To save energy, the display and The dryer saves the settings that were sensor controls will go out after selected last for a drying programme 10 minutes. The Start/Add laundry (drying stage and/or extra option, or button flashes slowly. -
Page 107: Programme Info
WiFi network. A new connection has to be established Please refer to “Before using for the first in order to use Miele@home again. time” for instructions on how to set up the connection. –... -
Page 108: Remote Control
Miele@home setting is set up and and activated. activated. Once the Miele@mobile app has been This function can be used for starting installed on your mobile device, you your tumble dryer automatically at a can check the status of your tumble... -
Page 109: Wash2Dry
If you do not install a RemoteUpdate, you can continue to use your tumble - Once a RemoteUpdate has been in- dryer in the usual way. However, Miele stalled, it cannot be undone. recommends installing RemoteUpdates. - Do not switch off the tumble dryer during a RemoteUpdate. -
Page 110: Factory Default
Settings Factory default All settings except Operating hours are reset to the factory default settings. Options Default settings The settings are reset to the factory default settings. Back The settings are not reset to the fact- ory default settings. Operating hours You can read off how many hours your tumble dryer has been in operation for. - Page 111 United Kingdom Miele Co. Ltd., Fairacres, Marcham Road, Abingdon, Oxon, OX14 1TW Tel: 0330 160 6600, Internet: www.miele.co.uk, E-mail: info@miele.co.uk Australia Ireland South Africa Miele Australia Pty. Ltd. Miele Ireland Ltd. Miele (Pty) Ltd. ACN 005 635 398 2024 Bianconi Avenue...
- Page 112 TWL 780 WP en-GB M.-Nr. 12 219 080 / 01...