Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Miele F1473 SF
Summary of Contents for Miele F1473 SF
- Page 1 Installation Instructions Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information. F1473 SF To prevent accidents and machine damage read these instructions before installation or use.
-
Page 2: Caring For The Environment
Caring for the environment Disposing of the packaging Disposal of your old appliance materials Old appliances may contain materials that can be recycled. Please contract The packaging is designed to protect your local recycling authority about the the appliance from damage during possibility of recycling these materials. -
Page 3: Climate Range
Installation Installation site Have the appliance installed by a The appliance should be installed in a qualified technician, according to dry, well ventilated room. the enclosed installation instructions. Do not install the appliance: - outdoors, - in an environment with dripping WARNING water, This appliance is top-heavy and... - Page 4 Installation Important! When there is high humidity a build-up of condensation on the outer surfaces of the appliance can occur.This can cause the surfaces to corrode.To prevent this, it is advisable to install the appliance in a dry and/or an air- conditioned room with sufficient ventilation.Please ensure that doors close and seal properly after...
-
Page 5: Installation Niche
See "Niche dimensions". If in doubt, contact Miele. The side walls of the installation cavity must be plumb. Furniture/fixtures The minimum thickness of the side... - Page 6 The "Merging Kit" is available from Miele. There are many different installation options. You are limited only by the Contact Miele or your dealer for design of the kitchen. specific information about which combinations will work with your The door hinge cannot be appliance.
-
Page 7: Side Panels
The "Merging Kit" will also be needed. The "Merging Kit" is available from Miele. Installation with partition without using the "Merging Kit" If there is a partition with a thickness of more than 6 "... - Page 8 20 11/16" (525 mm) 9 3/16" (234 mm) Miele recommends using the full door opening angle of 115° for this freezer. Power bars or extension cords are not safe (risk of fire). Do not use them to connect the appliance to the power supply.
- Page 9 Installation Niche dimensions F 1473 SF 18 ½" (469.8 mm) 18" (457 mm)
- Page 10 Installation Power supply and water connection 1. Power supply 2. Water connection F 1473 SF 9" (229 mm) Install a pressure limiting device and water hammer arrester for inlet water pressures exceeding 80 psi.(Refer to Uniform Plumbing Code, Sections 608.2 and 609.10) Never install or operate where inlet water pressure may exceed 120 psi.
-
Page 11: Installing The Appliance
Installing the appliance Before you begin Tools needed for installation – Cordless screwdriver Read these instructions completely and carefully. – Torx screwdriver Have the appliance installed by a – Hammer drill qualified technician, according to – Wood drills in different sizes the enclosed installation instructions. - Page 12 Installing the appliance Aligning the housing unit Check the installation niche To ensure a safe, trouble-free installation and the best possible cosmetic result, check to be sure that the installation space complies with the installation requirements. ^ Check the base (see "Installation"). ^ Check the dimensions of the cavity.
-
Page 13: Remotevision Module Installation
Installing the appliance RemoteVision module There are transportation safety installation devices inside the appliance to (optional accessory) protect the shelves and storage compartments until installation is Always disconnect the appliance complete. Do not remove them, or from the power supply when parts may be damaged. - Page 14 In that case, repeat the process. If that does not correct the Keep the appliance door closed problem, contact Miele. until it is securely fastened in the niche. Tipping hazard. Because of the size and weight of the appliance, it is essential to...
-
Page 15: Mounting Accessories
Installing the appliance Mounting Accessories The mounting accessories needed for installing the appliance into the niche are included in the packaging. Several plastic bags are included which are marked alphabetically. The bag needed for each step will be marked with its respective letter. Two anti-tip brackets are recommended for each appliance. - Page 16 Installing the appliance In a cabinet without a back wall ^ Now attach the installation niche to the wall. The built-in cabinet must be secured to the wall behind it with several screws. In a cabinet with a back wall ^ screw the cabinet to the wall behind it in several places using suitable mounting brackets.
- Page 17 Installing the appliance ^ Mark the installation height (lower Securing an alternative anti-tip edge of the beam) on the rear wall of device the niche. If the anti-tip brackets cannot be ^ Select screws according to the attached securely using a wooden beam, an alternative anti-tip device can thickness of the wooden beam.
- Page 18 Installing the appliance ^ Plug the appliance into the power Sliding the appliance into the outlet a. installation niche The plug of the appliance should be If a side-by-side installation is easily accessible after installation. desired, connect the two appliances If the plug is not accessible after the together.
- Page 19 Installing the appliance Aligning the appliance Important! ^ Align the appliance with the When unscrewing the height- surrounding cabinets. adjustable feet, proceed gradually, alternating between left and right. – Unscrew the height-adjustable feet until the mark on the base has reached the indicated guide dimension 1 1/4"...
- Page 20 Installing the appliance Attaching the appliance to the Attaching the toe-kick cover installation niche The maximum height of the toe-kick cover is 4" (102 mm) from the top of the floor. Do not cover the ventilation slits in the plinth. Risk of damage to the appliance.
- Page 21 Installing the appliance ^ Attach the toe-kick cover to the ^ Wedge the air separator at the plinth. bottom of the freezer door, so it connects in place. Mounting the air separator The air separator on the inside of the freezer door keeps the supply and exhaust air separate.
- Page 22 Installing the appliance Aligning the Ice/Water Dispenser If necessary the depth of the Ice/Water dispenser can be aligned from inside the custom door cut-out. This allows the dispenser to be aligned with the custom door to achieve the best possible appearance. Disconnect the appliance from the power supply.
- Page 23 Installing the appliance Once the drip tray has been removed, the four metal strips can be used to align the Ice/Water Dispenser. ^ Loosen the screws of the four metal strips. ^ Pull the rear cover forward and out. ^ Insert a screwdriver into one of the four slots and push sideways until the dispenser is aligned with the custom door (the gray arrow will adjust to the...
- Page 24 Installing the appliance Attaching the frame and the shelf The word "TOP" is marked on the rear of the frame at the top. " (19 mm) thick custom doors: ^ Slide the cover frame onto the Ice/ Water Dispenser and press until it is flush with the door front.
- Page 25 Do not use pipe extenders. Turn off the water supply before In the event that the piping has to be connecting the water lines to the ice replaced only Original Miele Spare cube maker. parts are suitable for use. Contact Miele.
-
Page 26: Preparing The Water Connection
Plumbing Preparing the water connection For appliances with a hose guide The connection to the household water supply must be installed before the appliance is installed. ^ Turn off the main water valve to prevent damage caused by leaking water. ^ Attach the connecting pipe to the shut-off valve, according to the instructions supplied by the... -
Page 27: Connecting The Water Supply
Plumbing ^ Push the union nut and seal onto the Connecting the water supply water pipe. When connecting the water pipe to ^ Push the end of the water pipe into the solenoid valve of the appliance, the appliance connection and screw follow the instructions supplied by on the union nut, 3. -
Page 28: Electrical Connection
If there are any questions regarding the electrical connection of this appliance to the power supply, please consult a licensed electrician or call the Miele Technical Service. U1-800-999-1360 V1-800-565-6435... -
Page 29: Remotevision (Optional Accessory)
'virtual link' between your following requirements appliance and our monitoring center. If – A wireless router that supports an a fault occurs, Miele's client service IEEE 802.11b/g protocol center will be notified and contact you, ® or another trusted individual identified –... - Page 30 RemoteVision (optional accessory) ^ Tap the X button until ; appears in Accessing the RemoteVision the display. control panel ^ Touch the access button "p" to confirm. See the table on the following page for a description of each setting in the ^ Touch the access button "p"...
- Page 31 RemoteVision (optional accessory) MasterCool control panel options for RemoteVision Status indicators Description of function Flashing ; ~ Module booting phase Flashing ; ‡ Not connected to network Flashing ; | Connection to network established, no IP address assigned Solid Connected to network Flashing ;...
- Page 34 F 1473 SF en - US, CA M.-Nr. 09 920 800 / 00...