Makita DTW1004 Instruction Manual
Cordless impact wrench
Hide thumbs
Also See for DTW1004:
- Instruction manual (112 pages) ,
- Instruction manual (112 pages) ,
- Instruction manual (96 pages)
Related Manuals for Makita DTW1004
Summary of Contents for Makita DTW1004
- Page 1 INSTRUCTION MANUAL Cordless Impact Wrench DTW1001 DTW1002 DTW1004 DTW800 DTW1001XV DTW1002XV DTW1004XV DTW800XV Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model: DTW1001 DTW1001XV DTW1002 DTW1002XV DTW1004 DTW1004XV DTW800 DTW800XV Fastening Standard bolt M12 - M30 M12 - M24 capacities High tensile M10 - M24 M10 - M22 bolt Square drive 19 mm 12.7 mm – Drive shank – 11.1 mm Hex. -
Page 3: Safety Warnings
Model DTW1004 / DTW1004XV Intended use Work mode: impact tightening of fasteners of the maxi- mum capacity of the tool The tool is intended for fastening bolts and nuts. Vibration emission (a ) : 18.4 m/s Model DTW800 / DTW800XV: The tool is also intended Uncertainty (K) : 1.7 m/s... - Page 4 Keep children and bystanders away while If devices are provided for the connection of operating a power tool. Distractions can cause dust extraction and collection facilities, ensure you to lose control. these are connected and properly used. Use of dust collection can reduce dust-related hazards. Electrical safety Do not let familiarity gained from frequent use Power tool plugs must match the outlet.
- Page 5 Use the power tool, accessories and tool bits Cordless impact wrench / impact etc. in accordance with these instructions, tak- drill safety warnings ing into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could For impact wrench result in a hazardous situation.
- Page 6 Avoid storing battery cartridge in a con- CAUTION: Only use genuine Makita batteries. tainer with other metal objects such as Use of non-genuine Makita batteries, or batteries that nails, coins, etc. have been altered, may result in the battery bursting Do not expose battery cartridge to water causing fires, personal injury and damage. It will or rain.
-
Page 7: Functional Description
Turn the tool off, and then turn it on again to restart. Charge the battery(ies) or replace it/them with recharged battery(ies). Let the tool and battery(ies) cool down. If no improvement can be found by restoring protection system, then contact your local Makita Service Center. Indicating the remaining battery capacity Fig.1 Only for battery cartridges with the indicator ► 1 . Red indicator 2. Button 3. Battery cartridge CAUTION: Always install the battery cartridge fully until the red indicator cannot be seen. -
Page 8: Electric Brake
NOTE: While pulling the switch trigger, the lamp status cannot be changed. This tool is equipped with an electric brake. If the tool NOTE: For approximately 10 seconds after releasing consistently fails to quickly stop after the switch trigger the switch trigger, the lamp status can be changed. is released, have the tool serviced at a Makita service center. 8 ENGLISH... - Page 9 ► 1 . Changed in three steps 2. Hard 3. Medium 4. Soft 5. Button Specifications of each impact force grade Impact force grade displayed Maximum blows Application on panel DTW1001 / DTW1002 / DTW1004 / DTW800 / DTW1001XV DTW1002XV DTW1004XV DTW800XV Hard 2,200 min (/min)
- Page 10 Impact force/bolt size corresponding chart (reference) Impact force grade DTW1001 / DTW1001XV DTW1002 / DTW1002XV DTW1004 / DTW1004XV DTW800 / DTW800XV displayed on panel Standard High ten- Standard High ten- Standard High ten- Standard High ten- bolt sile bolt bolt...
- Page 11 ► 1 . Impact socket 2. O-ring 3. Pin Tool with the detent pin Only for Model DTW1004 / DTW1004XV Align the hole in the side of the impact socket with the detent pin on the square drive and push the impact socket onto the square drive until it locks into place.
-
Page 12: Installing Hook
The hook is convenient for temporarily hanging the tool. Ring This can be installed on either side of the tool. To install the hook, insert it into a groove in the tool housing Country specific on either side and then secure it with two screws. To remove, loosen the screws and then take it out. CAUTION: Before using the ring, always make sure that the bracket and ring are secured... - Page 13 Model DTW1001 / DTW1001XV Model DTW1002 / DTW1002XV Proper fastening torque for standard bolt Proper fastening torque for standard bolt N•m N•m (kgf•cm) (kgf•cm) (8160) (8160) (6120) (6120) (4080) (4080) (2040) (2040) 1. Fastening time (second) 2. Fastening torque 1. Fastening time (second) 2. Fastening torque Proper fastening torque for high tensile bolt Proper fastening torque for high tensile bolt N•m...
- Page 14 Model DTW1004 / DTW1004XV Model DTW800 / DTW800XV Proper fastening torque for standard bolt Proper fastening torque for standard bolt N•m N•m (kgf•cm) (kgf•cm) (8160) (4080) (6120) (4080) (2040) (2040) 1. Fastening time (second) 2. Fastening torque 1. Fastening time (second) 2. Fastening torque...
-
Page 15: Optional Accessories
NOTE: Excessive fastening torque may damage the bolt/nut or impact socket. Before starting your job, ACCESSORIES always perform a test operation to determine the proper fastening time for your bolt or nut. CAUTION: These accessories or attachments NOTE: If the tool is operated continuously until the are recommended for use with your Makita tool battery cartridge has discharged, allow the tool to rest specified in this manual. The use of any other for 15 minutes before proceeding with a fresh battery accessories or attachments might present a risk of cartridge. injury to persons. Only use accessory or attachment The fastening torque is affected by a wide variety of for its stated purpose. - Page 16 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885A47-225 20230523...