Page 1
Operating instructions Dishwashers To avoid the risk of accidents or damage to the appliance, it is es- sential to read these instructions as well as the installation sheet be- fore it is installed and used for the first time. en-GB HG07-W M.-Nr.
Closing the door....................24 Miele@home ......................25 Basic settings ...................... 26 Setting the language ..................26 Setting up Miele@home ................. 26 Setting the time of day ................... 27 Setting the water hardness level ..............27 Activating AutoDos..................28 Dishwasher salt ....................29 Filling the salt reservoir ..................
Page 4
Contents Operation......................75 Switching on the dishwasher ................75 Selecting a programme ..................75 Display of programme duration ................76 Starting the programme ..................76 End of the programme ..................77 Energy management ................... 77 Switching off the dishwasher ................78 Unloading the dishwasher...................
Page 5
EPREL database ....................124 Warranty ......................124 Note for test institutes ..................124 Optional accessories ..................125 Installation......................127 The Miele Waterproof system................127 Water inlet ......................127 Water drainage ....................129 Electrical connection ..................131 Technical data....................132 EU Conformity declaration .................. 133...
Miele cannot be held liable for damage caused by non-compliance with these instructions. Keep the installation sheet and the operating instructions in a safe...
Page 7
Warning and safety instructions Appropriate use This dishwasher is intended for use in the home and in similar en- vironments, for example – in shops, offices and similar work settings – on agricultural estates – by the guests in hotels, motels, bed and breakfasts and other typ- ical home settings.
Page 8
Warning and safety instructions Safety with children Children under 8 years of age must be kept away from the dish- washer unless they are constantly supervised. Children aged 8 and older may only use the dishwasher without supervision if they have been shown how to use it in a safe manner. Children must be able to understand and recognise the possible dangers caused by incorrect operation.
Page 9
It is most important that this basic safety re- quirement is present. If in doubt, the electrical installation should be checked by a qualified electrician. Miele cannot be held liable for the consequences of an inadequate or lack of earthing system (e.g. electric shock). ...
Page 10
Warning and safety instructions There must be no electrical sockets behind the dishwasher be- cause the building-in niche may be too small. Danger of overheating and fire risk if the dishwasher were to be pushed up against a plug. ...
Page 11
Miele dealer or Miele Service. While the appliance is under warranty, repairs should only be un- dertaken by a Miele authorised service technician. Otherwise the warranty is invalidated.
Page 12
This lamp must only be used for the purpose for which it is in- tended. The lamp is not suitable for room lighting. Replacement lamps may only be fitted by a Miele authorised technician or by the Miele Customer Service Department.
Page 13
The appliance must only be operated with properly adjusted door springs. If the door cannot be adjusted properly, contact the Miele Customer Service Department. The minimum/maximum weight of the front panel is quoted in the technical data for your dishwasher on the Miele website.
Page 14
Warning and safety instructions Dishwasher detergents can cause burning on the skin and in the eyes, nose, mouth and throat. Avoid contact with detergents. Do not inhale powder detergents. Do not swallow dishwasher detergents. Seek medical attention immediately if detergent has been swallowed or inhaled.
Page 15
Please observe the information given in the “Technical data” chapter regarding the capacity of the dishwasher. Accessories and spare parts Only use original Miele accessories. If other parts are used, war- ranty, performance and, if applicable, product liability claims will be invalidated. ...
Notes on the operating instructions These operating instructions apply to Additional information and com- several different dishwasher models of ments different heights. Additional information and comments The different dishwasher models will be are highlighted in a box framed with a named as follows: single black line.
Scope The appliance is supplied with: - Dishwasher - Operating instructions for operating the dishwasher - Installation sheet for installing the dishwasher - Other installation accessories for in- stalling the dishwasher (see installa- tion sheet) - Funnel for filling the dishwasher salt - Additional printed matter and add- ons if required...
Guide to the appliance Appliance overview a Door locking pins i Salt reservoir b Top spray arm j Data plate c 3D MultiFlex cutlery tray k Rinse aid reservoir d Upper basket (depending on model) l Detergent compartment e Middle spray arm m AutoDos detergent outlet f Aeration valve n AutoDos (automatic dispensing)
Guide to the appliance Control field a On/Off sensor control g AutoDos sensor control For switching the dishwasher on and For activating/deactivating the Auto- off. Dos dispensing system. b Optical in-operation indicator light h Timer sensor control For indicating an ongoing wash pro- For selecting a later programme start.
Guide to the appliance The OK sensor control is used to con- Display functions firm a message, setting or programme The display is used to select or set the and also to move to the next menu or following: another level. - The programme Under Further programmes/settings, a scroll bar ...
Miele, free of charge. By law, you are solely responsible for deleting any personal data from the old appliance prior to disposal. You are legally obliged...
Before using for the first time If the door is opened during operation Every dishwasher is tested at the fact- all wash functions are automatically in- ory. There will be residual water in the terrupted. appliance from this test. It is not an in- dication that the dishwasher has been ...
Before using for the first time Closing the door Push the baskets right in. Raise the door upwards until the catch engages. At the end of the programme, if the AutoOpen function switched is on, the door locking pin must be fully re- tracted before the door is closed.
- A WiFi network Therefore, the availability of featured functions cannot be guaranteed. - The Miele app - A Miele user account The user ac- Miele@home availability count can be created via the Miele The ability to use the Miele app de- app.
Switching on the dishwasher pear in the display. Open the door. To set up Miele@home now, confirm Switch the dishwasher on using by touching OK. the sensor control. Tip: To postpone setup until later, select The welcome screen will appear when the option ...
Before using for the first time Setting the time of day Setting the water hardness level The display will change to the screen The time of day is set automatically if for setting the water hardness. a connection is established with the WiFi network.
Before using for the first time Activating AutoDos Finally, prompts will appear in the dis- play. The display changes to the settings screen for AutoDos (see “Detergent – After confirming these prompts with Automatic dispensing/AutoDos”). OK, the messages Refill salt ...
Before using for the first time Dishwasher salt If the water in your area is very soft and constantly lower than 0.9 mmol/l In order to achieve good cleaning res- (5 °dH – German scale), you do not ults, the dishwasher needs to operate need to add dishwasher salt.
Before using for the first time Filling the salt reservoir Before filling the salt reservoir for the first time, you must fill it with ap- prox. 1.5 l of water to enable the salt to dissolve. Once the dishwasher has been com- missioned, there is always sufficient water in the salt reservoir.
Before using for the first time Refilling salt After the salt reservoir has been filled, the salt refill indicator may still appear When the refill reminder Refill salt on the display if the salt concentration appears in the display, wait until the has not yet reached the correct level.
Before using for the first time Rinse aid If you only ever wish to use combina- tion products in your dishwasher, Rinse aid is necessary to ensure that you do not need to add rinse aid. water does not cling and leave marks However, for optimum rinsing and on crockery during the drying phase, drying results, use dishwasher deter-...
Before using for the first time Close the lid firmly until you hear it Adding rinse aid click into place. Otherwise, water can enter the rinse aid reservoir during a programme. Wipe up any spilled rinse aid. This prevents excess foam developing during the next programme.
Settings Changing settings You can alter the dishwasher’s con- trols to suit changing requirements by Use the sensor controls to select adjusting the settings. the menu option you want to change and confirm your selection with OK. The settings can be altered at any time.
Settings Language Time of day The display can be set to appear in one The current time of day must be set be- of several different languages. fore you can use the timer option. You can change the language used in Setting the clock format the display and also the country via the You can select either a 24-hour or 12-...
Settings Water hardness AutoDos (automatic dispens- ing) Your dishwasher is fitted with a water softener. Automatic dispensing automatically ad- justs the amount of detergent to the se- - You should programme the dish- lected programme. In the Auto pro- washer to the correct water hardness gramme, the quantity is adjusted de- for your area.
Settings Rinse aid Save Extras You can adjust the rinse aid dosage for You can set whether the selected extras best results. are to remain permanently activated for The rinse aid dosage can be set from 0 the respective programme. to 6 ml.
Settings Connect using App Miele@home The Miele app is available to download Your dishwasher is equipped with an in- free of charge from the Apple App tegrated WiFi module. ® Store or from the Google Play™ store. You can connect your dishwasher to your WiFi network.
Page 39
Deactivate As an alternative to networking via the If you do not wish to use the WiFi mod- Miele app, you can connect your dish- ule of your dishwasher, you can switch washer to your WiFi network using WPS it off.
Page 40
Settings Display Connection status Reset You can call up the current connection This menu option only appears if you status of your dishwasher. have already connected your dish- washer to your WiFi network. Select the Connection status menu op- tion and confirm with OK.
Even if the Remote control option is stalled automatically. They must be initi- switched off, you can use the Miele app ated manually. to call up information about your appli- ance. However, you cannot start any If you do not install an update, you can...
This menu option will only be dis- scope of a RemoteUpdate will be played if you have connected your provided in the Miele app. dishwasher to your WiFi network (see “Settings – Miele@home”). A message will appear in your dish- washer display if a software update is function is used for start-...
Settings Setting the electricity tariff times EcoStart Before you can use the EcoStart option, In order to run your dishwasher in the you must set at least one electricity tar- most economical way, you can use the iff time. EcoStart option to take advantage of your electricity supplier’s cheaper en- ...
Page 44
Settings Changing the electricity tariff times Deleting the electricity tariff times You can change the start, end or priority You can delete the settings for an elec- of an electricity tariff time. tricity tariff time and in doing so deac- tivate the EcoStart option for this time...
Settings Consumption display Volume (EcoFeedback) A sequence of buzzer tones will sound at the end of the programme or if there You can set whether the energy and is a fault as long as the buzzer se- water consumption is displayed for the quence has been activated.
If you only ever use combination deter- In some programmes the door automat- gent products or automatic dispensing ically opens slightly to assist the drying using Miele PowerDisks (if available), process. you can switch off the refill reminders This function can be deactivated if you for dishwasher salt and rinse aid if you wish.
Settings 2nd interim rinse Heat accumulator You can choose this function to in- This dishwasher is equipped with a heat crease the cleaning performance of the accumulator (see “Caring for the envir- programmes with a second interim onment – Heat accumulator”). rinse.
These items of software/software components are pro- - Total consumption tected by copyright. The copyrights - Fault memory held by Miele and third parties must be respected. - Data plate Furthermore, this communication mod- - Software version...
Caring for the environment - If you are manually dosing the deter- Economical dishwashing gent, reduce the amount of detergent This dishwasher is exceptionally eco- when using powder or liquid nomical in its use of water and electri- detergent if the baskets are only half city.
Caring for the environment 2. Display consumption EcoFeedback consumption in- dicator At the end of the programme you can call up the actual amount of energy and The Consumption indicator function is water used by the programme that has used for calling up information about just been run.
Caring for the environment Heat accumulator The heat accumulator can only be used in conjunction with a cold water This dishwasher is equipped with a heat connection. accumulator, in which fresh water for Selecting the hot water connection the programme is pre-heated and (see “Settings –...
Loading the dishwasher - The spray arms must not be blocked General information by items that are too tall or hang Remove coarse food residues from through the baskets. Test for free crockery. movement by manually rotating the spray arms. There is no need to pre-rinse items un- der running water.
Page 53
Loading the dishwasher Items not suitable for dishwashers: silver polish may still be damp or spot- ted at the end of a programme, where - Wooden cutlery and crockery or water has not run off smoothly. items with wooden parts: these may discolour and fade.
Loading the dishwasher Loading the FlexCare cup rack Upper basket You can put cups, small bowls and flat See the “Loading the dishwasher” crockery on the FlexCare cup rack. chapter, “Loading examples” section Glasses can be arranged along the cup for examples of how to load crockery rack so they sit securely during the pro- and cutlery.
Page 55
Loading the dishwasher Adjusting the FlexCare cup rack Loading the silicone elements of the FlexCare cup rack You can set the height and depth of the cup rack at two different levels. so that The silicone elements in the cup rack it can accommodate larger cups and so are specially designed to hold tall that taller crockery can be placed un-...
Page 56
Loading the dishwasher Lowering the spikes On both front right-hand rows of spikes, you can lower every other spike to make it easier to arrange larger crock- ery, e.g. cereal bowls. Press the yellow lever downwards , and then lower the dark grey spikes .
Loading the dishwasher Lower the upper basket: Adjusting the upper basket In order to gain more space for taller pieces of crockery in the lower basket or upper basket, the upper basket can be adjusted on 3 levels with 2 cm between each level. The upper basket can also be set at an angle so that water can run off freely from recesses.
Loading the dishwasher Lowering the spikes Lower basket The rows of spikes at the front are used See the “Loading the dishwasher” for loading plates, soup bowls, platters, chapter, “Loading examples” section dessert bowls and saucers. for examples of how to load crockery and cutlery.
Page 59
Loading the dishwasher FlexCare Glass & Bottle Loading the glass holders The glass and bottle holders are used The silicone elements in the glass to wash stemware, tall glasses and holder provide a stable and secure hold bottles. for delicate stemware. Adjusting the FlexCare Glass & Bottle You can set the glass and bottle holders at 2 different heights.
Page 60
Loading the dishwasher Loading the FlexCare Glass & Bottle The glass and bottle holders can be used to keep tall, narrow and hollow containers, e.g. beer glasses, bottles, vases, secure during a programme. Lean the containers into the holders. Tip: For the best cleaning results, use the “BottleClean”...
Page 61
Loading the dishwasher MultiClip The MultiClips enable you to fasten light load items such as those made from plastic. Slightly lift the XL-Assist , fold it out and hook it back in the new position . Secure light items to the MultiClips. Make sure that crockery does not obstruct the middle spray arm.
Loading the dishwasher You can push the left insert to the Cutlery tray/cutlery basket middle in order to accommodate tall (depending on model) items of crockery and long stemmed See the “Loading the dishwasher” glasses in the upper basket (see “Upper chapter, “Loading examples”...
Loading the dishwasher Loading the cutlery basket (if present) Fit the insert onto the cutlery basket if required. The cutlery basket can be placed any- where on the front rows of spikes in the left or right corner of the lower basket. ...
Detergent There are different types of detergent: Active ingredients - Powder and liquid gel detergents. Risk of damage due to unsuit- These detergents allow you to adjust able detergents. the amount dispensed according to Detergents that are not suitable for the load size and the level of soiling.
Detergent Detergent dosage Risk of chemical burns from de- tergent. There are two ways of dispensing the Dishwasher detergents can cause detergent. burning on the skin and in the eyes, During automatic dispensing the Auto- nose, mouth and throat. Dos will automatically dispense the re- Avoid contact with detergents.
Insert a PowerDisk (see “Automatic on the chosen programme. dispensing/AutoDos – Inserting a PowerDisk”). PowerDisks are available to order dir- ectly from the Miele online shop, the The AutoDos function will be activ- Miele Customer Service Department ated automatically. or from your Miele dealer.
Detergent Inserting a PowerDisk Only replace the PowerDisk when the message PowerDisk empty. Deactivate AutoDos with OK appears. Insert the new PowerDisk and press it evenly downwards until it sits flush. Turn the AutoDos lid to and open The message will ap- AutoDos lid open...
Page 72
Detergent The detergent powder must be dry so that it does not clump together. Do not fill the AutoDos with any type of fluid. It is not permitted to refill the PowerDisk with powder detergent. This will invalidate the warranty. In order to ensure that the AutoDos function works at its best, check it each time you replace the PowerDisk...
Detergent Adding detergent Manual detergent dispensing Detergent must be manually dispensed if you have deactivated automatic dis- pensing using the AutoDos sensor control. Dispensing detergent The detergent compartment holds a maximum of 50 ml. There are marks in the detergent com- partment as a dispensing aid: 20, 30, max.
Page 74
Detergent The detergent must not cause the detergent compartment lid to get stuck. This can prevent the lid from opening during the programme se- quence. Do not overfill the detergent com- partment. If you wish, deactivate automatic dis- pensing/AutoDos. ...
Operation Switching on the dishwasher Selecting a programme Open the stopcock, if it is closed. Choose your programme according to the type of dishes and the degree of Open the door. soiling. Make sure the spray arms can rotate The different programmes and their freely.
Operation Display of programme duration Starting the programme Start the programme by closing the The estimated duration of the selected programme appears on the display be- door. fore the programme begins. If the door If necessary, confirm the previously is opened during the programme, the displayed message with OK.
Operation End of the programme Risk of damage due to steam. Steam from the dishwasher could At the end of a programme, the in-oper- damage delicate housing units and ation indicator light will flash slowly with the edges of worktops when you the door shut.
Operation Switching off the dishwasher Unloading the dishwasher Open the door. Dishes tend to break and chip more easily when they are hot. Allow the The dishwasher can be switched off dishes to cool until they are comfortable at any time using the ...
Operation Interrupting a programme Cancelling or changing a pro- gramme A programme will be interrupted as soon as the door is opened. If a programme is cancelled, import- If the door is closed again, the pro- ant programme stages may be gramme will continue from the point it missed.
After you have activated the timer, all the displays will switch off after a few minutes to save energy. You can also activate a timer via the Miele app.
Page 81
Options Setting “Start at” Setting “Finish at” With the Start at function, you set the Use the Finish at function to set the exact time you want the programme to latest time by which the selected pro- start at. gramme has to be finished. ...
Page 82
Options Setting EcoStart Setting SmartStart You can use the EcoStart function to be- SmartStart function is used for start- nefit from cheaper energy tariffs at ing your dishwasher automatically at a night. Before you can use this option, time when your energy supplier’s elec- you need to set up to three electrical tricity tariff is most economical.
Page 83
You can now start a programme or switch the dishwasher off. Switching the dishwasher off while a timer is running stops the timer. You can also change the time set for the timer or delete it using the Miele app.
You can start your dishwasher remotely ing the sensor control. The option using the Miele app. To do this, you first will also remain active if you switch the need to install the app on your mobile...
Options Displaying the operating hours You can display how many hours the dishwasher has been in operation so far. Open the door. Switch the dishwasher on using the sensor control. If necessary, confirm the messages and refill reminders with OK. ...
Guide for selecting a programme Crockery Food deposits Programme features Mixed crockery including Lightly dried-on Balanced and temperature-sensitive glasses normal food gentle programme and plastics deposits All normal Variable, food deposits sensor-controlled programme Water and Mixed crockery energy saving programme Standard dried-on normal food deposits...
Page 87
Guide for selecting a programme Programme Consumption estimate Energy consumption Water consumption ComfortWash 45 °C Programme duration Energy consumption Auto Water consumption Programme duration Energy consumption Water consumption Programme duration Energy consumption Water consumption PowerWash 60 °C Programme duration Energy consumption Water consumption Intensive 75 °C ...
Programme overview Programme Programme sequence Pre-wash Main wash Interim rinse Final rinse Drying/ AutoOpen °C °C / Auto 45–60 °C Variable programme sequence, sensor-controlled adjustment according to load size and level of soiling / 45–60 55–70 required ComfortWash...
Page 89
Programme overview Consumption Electrical energy Water Time Cold water Hot water Litres Cold water Hot water 15 °C 60 °C 15 °C 60 °C h:min h:min 0.54 0.29 3:50 3:40 0.65–0.95 0.55–0.65 6.0–13.0 2:02–2:59 1:59–2:49 0.85 0.45 12.5 2:38 2:28 1.00 0.65 1:26 1:15 1.25 0.85 13.5...
Programme overview Further programmes SolarSave Programme operating without heating ComfortWash+ 55 °C when the dishwasher is connected to a Programme for cleaning a mixed load of hot water supply of at least 45 °C (see crockery with normal household food “Installation – Water inlet”). This pro- residues.
Page 91
Programme overview Maintenance programme Rinse out salt The dishwasher wash cabinet is gener- Programme for rinsing the wash cabinet ally self-cleaning. However, if residues after filling the salt reservoir. Each time or deposits occur, use the Mainten- you remove the salt reservoir cap, im- programme to clean it.
Extras IntenseZone Selecting extras You can select the IntenseZone extra to You can use extras to adjust the pro- increase the cleaning performance of grammes. the programmes in the lower basket. To do this, you can select or deselect When this extra is activated, the pro- the extras before starting the selected gramme running time is extended and programme.
Extras Touch the Quick sensor control. Selecting Quick The sensor control will light up if the ex- You can reduce the programme running tra is available for the programme se- time using the Quick extra. lected. The time by which the programme run- If the extra is not compatible with the ning time is shortened varies according selected programme, a message to this...
– Appliance care”). Follow the instructions on the product packaging. Miele cleaning and care products are available to order from the Miele Cus- tomer Service Department or from the Miele online shop. Clean the filters in the wash cabinet...
Cleaning and care Hygiene cycle Cleaning the door and the door seal If you mainly use low temperature pro- grammes, there is a risk of bacteria and The door seal and the sides of the dish- unpleasant odours building up in the washer door cannot be reached and wash cabinet.
Cleaning and care To avoid damaging the external sur- Cleaning the appliance front faces, do not use the following: Damage due to soiling. - Cleaning agents containing soda, Soiling that is left too long might be- ammonia, acids or chlorides come impossible to remove and - Descaling agents could cause the external surfaces to...
Cleaning and care Turn the AutoDos lid to and open Cleaning the AutoDos If the message is dis- Clean AutoDos Remove the PowerDisk if appropriate. played, check that the AutoDos is clean, and clean it if necessary, e.g. powder residues.
Page 98
Cleaning and care The AutoDos lid must close tightly so that the detergent powder does not get wet and clump together. Make sure that all seals are clean and clean them if necessary. Insert a filled PowerDisk and press it evenly downwards until it sits flush.
Cleaning and care Removing the cutlery tray (if present) Cleaning the spray arms In order to be able to remove the upper Particles of food can get stuck in the spray arm, you first have to remove the spray arm nozzles and bearings. The cutlery tray (if present).
Page 100
Cleaning and care Removing the top spray arm Removing the lower spray arm Remove the lower basket. Push the upper spray arm upwards to engage the inner ratchet. Then un- Rotate the screw thread of the lower screw the spray arm by rotating the spray arm anti-clockwise ...
Page 101
Cleaning and care Cleaning the spray arms Inserting the upper spray arm Refit the upper spray arm and tighten it by hand. Inserting the middle spray arm Use a pointed object to push food particles into the spray arm nozzles. ...
Page 102
Cleaning and care Inserting the lower spray arm Inserting the cutlery tray (if present) Refit the lower spray arm and ensure Slide the cutlery tray back onto the that the filter combination lies flat in rails from the front. the base of the wash cabinet.
Cleaning and care Checking the filters in the Cleaning the filters wash cabinet Switch the dishwasher off. The filter combination in the base of the Remove the lower spray arm (see wash cabinet retains coarse soiling “Cleaning and care” chapter, “Clean- from the suds solution.
Page 104
Cleaning and care In order to clean the inside of the fil- Rotate the screw connection clock- ter, pull the microfilter on the plastic wise until the arrow in the viewing ring downwards and away from the window points to the lock symbol . filter combination.
Cleaning and care Cleaning the water inlet filter A filter is incorporated in the screw thread to protect the water inlet valve. If the filter is soiled, insufficient water flows into the wash cabinet. Risk of electric shock from mains voltage.
Cleaning and care Cleaning the drain pump If water remains in the wash cabinet after the end of the programme, the wa- ter has not been pumped away. The drain pump may be blocked by foreign objects. These foreign objects are easy to remove.
Page 107
Cleaning and care Damage due to incorrect clean- ing. The components are delicate and can be damaged during cleaning. Take care when cleaning the drain pump. The drain pump (see arrow) is under- neath the cover. Risk of injury from glass splin- ters.
You can save time and money in many cases, as you do not need to call the Miele Customer Service Department. Information to help you rectify faults yourself can be found at www.miele.com/ser- vice. The following tables are designed to help you to find the cause of a malfunction or a fault and to resolve it.
Page 109
Reset the mains fuse (see data plate for minimum protection rating). If the mains fuse trips again, contact the Miele Customer Service Department. After the programme The reflector panel was not correctly fitted.
If the fault message appears again, there is a tech- nical fault. Switch the dishwasher off. Close the stopcock. Call the Miele Customer Service Department. Waterproof The Waterproof system has reacted. Switch the dishwasher off.
– Opening the door”) and switch the dishwasher back on again. If the same fault message appears again, call the Miele Customer Service Department. The door locking pins do not retract after the door is opened. There may be a technical fault.
Problem solving guide Water inlet fault Problem Cause and remedy The optical in-operation indicator light is flash- ing quickly. The alarm tone is sounding. One of the following messages appears in the display: Open stopcock The stopcock is closed. ...
Problem solving guide Water drainage fault Problem Cause and remedy The optical in-operation Before rectifying the problem: indicator light is flash- Switch the dishwasher off. ing quickly. Water drainage fault. The alarm tone is There might be water in the wash cabinet. sounding.
“Inserting a PowerDisk” section). gramme that has If the same fault message appears again, call the already started stops. Miele Customer Service Department. The message AutoDos lid open appears in the dis- play The AutoDos function is active and the PowerDisk...
Page 115
(see “Detergent – Manual deter- gent dispensing”). If you wish to use automatic dispensing again, contact the Miele Customer Service Department. The in-operation indic- No or an empty PowerDisk has been inserted or the ator light is flashing AutoDos is blocked by residual detergent.
Problem solving guide Spray arm fault Problem Cause and remedy During the programme The bottom spray arm is blocked or the nozzles of and at the end of the the bottom spray arm are clogged. The AutoDos de- programme, the display tergent outlet may not be completely flushed out.
Problem solving guide General problems with the dishwasher Problem Cause and remedy The indicator lights and The dishwasher has switched off automatically to the display are dark. save energy. Switch the dishwasher back on using the sensor control. Detergent residue is left The detergent compartment was still damp when de- in the detergent com- tergent was added.
Problem solving guide Noises Problem Cause and remedy Knocking noise in the A spray arm is knocking against a wash item. wash cabinet Carefully open the door and rearrange the wash items that are obstructing the spray arm. Rattling noise in the Wash items are insecure in the wash cabinet.
Problem solving guide Unsatisfactory washing result Problem Cause and remedy The crockery is not The crockery was not loaded correctly. clean. See notes under “Loading the dishwasher” for ex- amples on how to load crockery and cutlery. The programme was not powerful enough. ...
Page 120
Problem solving guide Problem Cause and remedy The crockery is not dry The rinse aid dosage is too low or the rinse aid con- or cutlery and glasses tainer is empty. are flecked. Replenish the rinse aid container, increase the dosage or change the brand of rinse aid (see “Be- fore using for the first time –...
Page 121
Problem solving guide Problem Cause and remedy White residue is visible The rinse aid dosage is set too low. on the crockery. Cloud- Increase the dispensing quantity (see “Settings – ing has occurred on Rinse aid”). glassware and cutlery. There is no salt in the salt reservoir.
Page 122
Problem solving guide Problem Cause and remedy There are rust stains on The affected items are not corrosion-resistant. cutlery. No remedy. Purchase cutlery that is dishwasher-proof. A programme was not run after dishwasher salt was added. Traces of salt have got into the normal wash cycle.
Contact in the event of a fault In the event of any faults which you cannot remedy yourself, please contact your Miele dealer or the Miele Customer Service Department. You can book a Miele Customer Ser- vice Department call-out online at www.miele.com/service.
Made in xxxx Warranty For information on the appliance war- ranty specific to your country please contact Miele. See back cover for ad- dress. In the UK, your appliance warranty is valid for 2 years from the date of pur- chase.
Optional accessories Dishwasher detergent, rinse aid and In hard water areas, we recommend us- cleaning and care products are avail- ing the complete Miele system: the able for this dishwasher, as are optional PowerDisk, rinse aid and salt perfectly accessories.
Page 126
Optional accessories Appliance care Miele cleaning and care products provide optimum care for your Miele dishwasher. Dishwasher cleaner - For use with the Maintenance pro- gramme without detergent dispens- - Cleans the dishwasher effectively and thoroughly - Removes grease, bacteria, and asso-...
(tested to 14,000 kPa/ which the dishwasher is being oper- 140 bar) is available as an optional ac- ated. cessory from Miele dealers or the Miele Connect the dishwasher to a drinking Customer Service Department. water supply. A stopcock with a ¾" threaded union is required for the connection.
Page 128
*INSTALLATION* Installation Risk of damage from leaking wa- ter. The connection point is subject to mains water pressure. Water leaking from it can cause damage. You should therefore open the stop- cock slowly and check for leaks. Correct the position of the seal and screw thread if appropriate.
*INSTALLATION* Installation Water drainage Lay the drain hose so that it does not kink and is not being subjected to The dishwasher’s drainage system is fit- pressure or tension. ted with a non-return valve, which pre- vents dirty water from flowing back into ...
Page 130
*INSTALLATION* Installation Venting the water drain If the on-site drainage connection is situated lower than the guide path for the lower basket rollers in the open door, the drainage system must be ven- ted. Otherwise, a siphoning effect can cause the wash cabinet to empty itself of water during a programme.
The electrical installation must comply Miele product must also be maintained with VDE 0100 requirements. in isolated operation or in operation that is not synchronised with the mains...
Technical data Technical data Dishwasher model Normal Height 80.5 cm 84.5 cm (adjustable by (adjustable by +6.5 cm) +6.5 cm) Height of building-in niche Min. 80.5 cm (+6.5 cm) Min. 84.5 cm (+6.5 cm) Width 59.8 cm 59.8 cm Width of building-in niche 60 cm 60 cm Depth 55 cm 55 cm Weight Max. 47 kg Max.
UK Conformity declaration Miele hereby declares that this dishwasher complies with UK Radio Equipment Regulations 2017, as amended. The complete text of the UK declaration of conformity is available from one of the following internet addresses: - Products, Download from www.miele.co.uk...
Page 135
United Kingdom Miele Co. Ltd., Fairacres, Marcham Road, Abingdon, Oxon, OX14 1TW Tel: 0330 160 6600, Internet: www.miele.co.uk, E-mail: info@miele.co.uk Australia Ireland South Africa Miele Australia Pty. Ltd. Miele Ireland Ltd. Miele (Pty) Ltd. ACN 005 635 398 2024 Bianconi Avenue...
Page 136
G 7650, G 7652, G 7655, G 7657, G 7672, G 7677 en-GB M.-Nr. 12 474950 / 01...