Table of Contents
Related Manuals for Miele PDR 1108 HP SmartBiz
Summary of Contents for Miele PDR 1108 HP SmartBiz
- Page 1 Operating and installation instructions Heat-pump dryer To avoid the risk of accidents or damage to the appliance it is essen- tial to read these instructions before it is installed and used for the first time. en-GB M.-Nr. 12 646 520...
-
Page 2: Table Of Contents
Initial commissioning ....................20 Installation........................20 Information about networking ..................20 Miele@home......................20 Wash2Dry ......................21 Setting up Miele@home ....................22 1. Notes on correct laundry care................23 Washing ........................... 23 Drying ..........................23 Care label symbols ......................23 2. Load the tumble dryer ..................... 24 Checking the socket for the fragrance flacon............. - Page 3 Contents Programme overview ....................31 Changing the programme sequence ................ 34 Changing a programme once it has started ............... 34 Adding or removing laundry ..................34 Fragrance flacon......................35 FragranceDos........................35 Removing the protective seal from the fragrance flacon.......... 35 Inserting the fragrance flacon..................
- Page 4 Contents Locations ......................... 57 Side view........................57 View from above ....................... 57 Washer-dryer stack ....................58 Transporting the tumble dryer to its installation site ..........58 Installation........................59 Downtime after installation..................60 Levelling the tumble dryer ..................60 Room ventilation ....................... 61 Hose for external drainage of condensed water ............
-
Page 5: Caring For The Environment
Caring for the environment local community, with your dealer or Disposing of the packaging ma- with Miele, free of charge. By law, you terial are solely responsible for deleting any The packaging material is used for hand- personal data from the old appliance ling and protects the appliance from prior to disposal. -
Page 6: Warnings And Safety Instructions
Miele cannot be held liable for damage caused by non-compliance with these instructions. Keep these operating instructions in a safe place and pass them on to any future owner. - Page 7 If using, do so at your own risk, and follow the instruc- tions provided on the packaging. Any other applications may be dan- gerous. Miele cannot be held liable for damage resulting from incor- rect or improper use or operation.
- Page 8 If the electrical connection cable is faulty it must always be re- placed by a Miele authorised service technician to protect the user from danger. The electrical safety of this tumble dryer can only be guaranteed ...
- Page 9 This special lamp must only be used for the purpose for which it is intended. It is not suitable for room lighting. Replacement lamps may only be fitted by a Miele authorised person or by Miele Service.
- Page 10 - Disconnect the tumble dryer from the electrical supply. - Air the room where the tumble dryer is located. - Contact the Miele Customer Service Department. Risk of fire and explosion due to damage to the tumble dryer. The refrigerant is flammable and explosive if it leaks.
- Page 11 Warnings and safety instructions Correct use The maximum load for this tumble dryer is 8 kg (dry weight).The maximum recommended loads for individual programmes are given in the Programme chart. Do not lean on the door. Otherwise, the tumble dryer may tip over, causing injury to yourself or others.
- Page 12 Warnings and safety instructions Do not install the tumble dryer in a room where there is a risk of frost occurring. At temperatures around freezing point the tumble dryer may not be able to operate properly. There is a risk of damage if the condensed water is allowed to freeze in the pump or hoses.
- Page 13 Warnings and safety instructions In many programmes, the heating phase is followed by a cooling down phase to ensure that the items are not too hot to handle when you remove them (this also avoids the danger of the laundry self-ig- niting).
- Page 14 Aggressive vapours containing chlorine can also be corrosive. Do not store containers of these agents near the tumble dryer. Using a fragrance flacon (optional accessory) Only ever use original Miele fragrance flacons. The fragrance flacon must be stored in its packaging so please make sure you retain this.
- Page 15 If spare parts or accessories from other manufacturers are used, this will invalidate the guarantee, and Miele cannot accept liability. The tumble dryer can also be combined with a Miele washing ma- chine in a washer-dryer stack (stacked machines cannot go on a plinth).
- Page 16 Warnings and safety instructions Miele cannot be held liable for damage caused by non-compli- ance with these Warning and Safety instructions.
-
Page 17: Operating The Tumble Dryer
Operating the tumble dryer Control panel a Control field f Sensor controls for time selection b Sensor controls for the drying levels g Start/Add laundry sensor control c Indicator lights Touching the Start/Add laundry light up when necessary sensor control starts a programme. -
Page 18: How The Programme Selector Works
MobileStart You can operate your tumble dryer re- motely with the Miele app. The , , and sensor controls react to fingertip contact. If a sensor Wash2Dry control is lit, it can be selected. A drying programme tailored to the... -
Page 19: Drum Lighting
Operating the tumble dryer Indicator lights The electronic module adapts to these parameters and then adjusts the pro- - gramme duration with increasing accur- lights up if condensate drainage via acy. the drain hose is hindered. Sensor controls - ... -
Page 20: Initial Commissioning
- The Miele app correctly. Follow the instructions in - A Miele user account. You can create “Installation”. a user account via the Miele app. The Miele app will guide you as you ... -
Page 21: Wash2Dry
The tumble dryer automatically sets a drying programme tailored to the laun- Miele@home availability dry based on the transferred pro- The ability to use the Miele app de- gramme data. pends on the availability of the All you need to do is start the drying Miele@home service in your country. -
Page 22: Setting Up Miele@Home
2. Via WPS To do so, you will need a WPS-com- patible router. Logging in via the Miele app The Miele app can be used to connect to your network. Turn the programme selector to Mo- bileStart . appears on the time display and the timeout starts to count down from 10 minutes. -
Page 23: Notes On Correct Laundry Care
1. Notes on correct laundry care Washing Care label symbols - Heavily soiled laundry must be Drying washed particularly thoroughly. Use Normal/higher temperature sufficient detergent and select a high temperature. If in doubt, wash the Low temperature* items several times. * Select Gentle tumble - New, coloured items must be washed thoroughly and separately. -
Page 24: Load The Tumble Dryer
2. Load the tumble dryer Loading the laundry Checking the socket for the fra- grance flacon Preventing textile damage. If you are not using a fragrance flacon, Before loading, read chapter “1. check that the socket is closed. Notes on correct laundry care.” The “Fragrance flacon”... -
Page 25: Selecting A Programme
lector position Turn the programme selector to Mo- bileStart . will light up on the time display. Touch the Start/Add laundry sensor control. The tumble dryer can now be operated via a mobile device together with the Miele app. -
Page 26: Selecting Programme Settings
3. Selecting a programme Selecting the Warm air duration Selecting programme settings You can set the duration in ten-minute Selecting the drying level increments from minutes to Check the “Programme chart” to see hours. which programme you can select a dry- ... -
Page 27: Starting The Programme
4. Starting the programme Energy saving Starting a programme Indicators are switched off after Touch the flashing Start/Add laundry 10 minutes. The Start/Add laundry sensor control. sensor control flashes slowly. The Start/Add laundry sensor control Touch the Start/Add laundry sensor lights up. -
Page 28: End Of Programme - Unloading The Drum
5. End of programme – unloading the drum End of programme Unloading the drum The laundry will be cooled down shortly before the end of the programme. The laundry can now be unloaded. The programme has ended when only is left on the display. If Anti-crease (see “Programmable functions”) has been selected, the drum rotates in intervals. -
Page 29: Delay Start/Smartstart
Delay start/SmartStart Selecting the Delay start func- Starting Delay start tion Touch the Start/Add laundry sensor control to start the Delay start func- With Delay start, you can delay the tion. start of a programme from minutes up to (hours). - Delay start times of more than ... -
Page 30: Smartstart
Delay start/SmartStart Setting the time period SmartStart If the SmartGrid programmable The SmartStart function lets you function is activated, the function of define a time period during which your the sensor control changes. The tumble dryer will start automatically. time display no longer shows the The appliance will start on receipt of a Delay start period, and instead shows signal, e.g. -
Page 31: Programme Overview
Programme overview All weights marked with * are based on the weight of dry laundry. Cottons Maximum 8 kg* Extra dry, Cupboard Dry Items - Single and multi-layered cotton items. - Towelling, bathrobes, T-shirts, underwear, jersey/terry bed linen, baby clothes. - Workwear, jackets, cotton blankets, aprons, tea towels, bed linen, towels, table linen. - Page 32 Regulation 392/2012/EU for energy labelling, measured in ac- tutes cordance with EN 61121. MobileStart The Miele app is used to select programmes and operate the appliance. Wash2Dry The programme is selected automatically in conjunction with the programme se- lection on the connected washing machine.
- Page 33 Programme overview Towelling Maximum 8 kg* Items Large quantities of single-layered and multi-layered towelling items. These include, for example, towels, bathrobes, face flannels, flannel bed linen. Note Items are dried to a Extra dry level only in this programme. Express Maximum 4 kg* Extra dry, Cupboard Dry, Hand iron, Machine iron Items Garments suitable for the Cottons programme...
-
Page 34: Changing The Programme Sequence
Changing the programme sequence Changing a programme once it Adding or removing laundry has started You have forgotten something but the programme is already running. It is no longer possible to change the selected programme. This is to prevent Touch the Start/Add laundry sensor the operation of the appliance being control. -
Page 35: Fragrance Flacon
Fragrance flacon FragranceDos Removing the protective seal from the fragrance flacon Fragrance flacons (optional accessor- ies) can be used to give your laundry a Only hold the fragrance flacon as il- pleasant scent. lustrated. Do not hold it at an angle or tip it, as the fragrance will leak out This dryer has 2 places for inserting of it. -
Page 36: Inserting The Fragrance Flacon
Fragrance flacon Inserting the fragrance flacon Open the door of the tumble dryer. The fragrance flacon is inserted in the upper fluff filter. They can be fitted on the left and the right hand side next the opener. Insert the fragrance flacon into the socket as far as it will go. -
Page 37: Opening The Fragrance Flacon
Fragrance flacon into the laundry effectively. The fra- grance will also be noticeable in the room air during the process. Closing the fragrance flacon After drying, the fragrance flacon should be closed to prevent the fragrance from escaping needlessly. -
Page 38: Removing/Replacing The Fragrance Flacon
- Always store in a cool, dry place away from direct sunlight. Fragrance flacons are available to order - When purchasing new fragrance flac- from Miele or online at www.miele- ons, only remove the protective seal shop.com. just before use. -
Page 39: Cleaning And Care
Cleaning and care Observing the cleaning intervals Cleaning the fluff filters This tumble dryer is equipped with a This tumble dryer has 2 fluff filters in multi-stage filter system, which con- the door opening: the upper and lower sists of a fluff filter and a plinth filter. fluff filters trap fluff produced during This filter system collects all fluff gen- the drying process. -
Page 40: Removing Visible Fluff
Cleaning and care Removing visible fluff Tip: You can also use a vacuum cleaner so that you can remove the fluff without touching it. Open the door. Remove the fluff (see arrows) from the surface of all the fluff filters and the perforated laundry deflector. -
Page 41: Cleaning The Fluff Filters And Air Flow Openings Thoroughly
Cleaning and care Cleaning the fluff filters and air flow Hold the rotary control and pull the openings thoroughly fluff filter forwards to remove it. If the drying duration has become longer or the surface of the fluff filters is visibly compacted with fluff, you should carry out the following cleaning procedure. - Page 42 Cleaning and care Cleaning the fluff filters with water Close the door. Rinse the filter surfaces through un- der warm running water. Wipe the smooth plastic surfaces of both fluff filters with a damp cloth to clean them. Problems during drying due to wet fluff filters.
-
Page 43: Cleaning The Plinth Filter
Cleaning and care Removing the plinth filter Cleaning the plinth filter Clean the plinth filter whenever the indicator light comes on or when the programme duration is longer than usual. To turn the indicator light off: Open and close the door while the tumble dryer is switched on. -
Page 44: Cleaning The Plinth Filter
There will be an insufficient flow of air and heat in the heat exchanger. Tip: To speed up the removal of residue This will require a visit from Miele from the surface, run a water jet vertic- Customer Service. ally over the front of the plinth filter. -
Page 45: Replacing The Plinth Filter
Cleaning and care Replacing the plinth filter Poor fit Filter wear caused by continuous tumble dryer use. If the tumble dryer is in continuous use and is being cleaned regularly, the plinth filter can begin to show signs of wear after a while. This can clog up the heat exchanger. - Page 46 Cleaning and care Cracks, tears, indentations White residues or residues of other col- ours Residues arise from laundry fibres and traces of detergent components which can clog the filter. They can be found on the front and side edges of the filter. In extreme cases, they can form stubborn crust.
-
Page 47: Cleaning The Plinth Filter Flap
Cleaning and care Cleaning the plinth filter flap Checking the heat exchanger Risk of injury from sharp cooling fins. You could cut yourself. Do not touch the cooling fins with your hands. Look to see if fluff has accumulated. If you notice any visible soiling: ... -
Page 48: Inserting The Plinth Filter
- The word Miele on the handle must You must stop using the plinth filter if be the correct way up. it shows signs of wear or deforma- tion. -
Page 49: Cleaning The Tumble Dryer
Cleaning and care Cleaning the tumble dryer Disconnect the tumble dryer from the electrical supply. Damage caused by the use of un- suitable care products. Unsuitable care products could dam- age plastic surfaces and other parts. Do not use any solvents, abrasive cleaners, glass cleaners, or all-pur- pose cleaners. -
Page 50: Problem Solving Guide
You can save time and money in many cases, as you do not need to call the Miele Customer Service Department. Information to help you rectify faults yourself can be found at www.miele.com/ser- vice. The following tables are designed to help you to find the cause of a malfunction or a fault and to resolve it. - Page 51 Start a programme. cancelled, a signal If the programme terminates again with the same er- sounds. ror message, then there is a fault. Contact the Miele Customer Service Department. : lights up and the The laundry is unevenly distributed or has rolled up.
-
Page 52: Unsatisfactory Drying Results
Problem solving guide Unsatisfactory drying results Problem Cause and remedy The laundry is not suffi- The load consisted of different types of fabric. ciently dry. Finish drying using the Warm air programme. Select a more suitable programme next time. Useful tip: You can alter the drying levels for some programmes. -
Page 53: The Drying Cycle Duration Is Very Long
Problem solving guide The drying cycle duration is very long Problem Cause and remedy The drying process goes The room where the tumble dryer is located is too on too long or even warm. switches off.* Ventilate the room thoroughly. Detergent residues, hair and fine fluff can clog the fil- ters. -
Page 54: Other Problems
The drum lighting is designed to last a long time and should not normally need to be replaced. If you have tried everything but the drum lighting still does not come on, contact the Miele Cus- tomer Service Department. -
Page 55: Service
In the event of any faults which you can- Optional accessories for this tumble not remedy yourself, please contact dryer are available from your Miele your Miele dealer or the Miele Cus- Dealer or from the Miele Spare Parts tomer Service Department. Department. -
Page 56: Installation
*INSTALLATION* Installation Front view a Mains connection cable e 4 height-adjustable screw feet b Control panel f Intake for air cooling – Do not obstruct with a laundry c Door basket or other objects d Fluff filter flap for the filter in the g Drain hose for condensation plinth h Non-return valve, required... -
Page 57: Rear View
*INSTALLATION* Installation Rear view Locations All measurements in mm Side view 1054 a Protruding lid for holding when mov- ing the tumble dryer (see arrows) b Drain hose for condensation c Hook for winding the mains connec- tion cable around during transport View from above d Mains connection cable 1054... -
Page 58: Washer-Dryer Stack
Transporting the tumble dryer A stacking kit* is required. This must be fit- ted by a Miele authorised technician. The distance between the appliance and the wall is a recommendation to help make it easier to carry out service work. -
Page 59: Installation
- Air the room where the tumble dryer is located. Carry the tumble dryer by the front feet and by the lid where it protrudes - Contact the Miele Customer Service at the back of the appliance. Department. -
Page 60: Downtime After Installation
*INSTALLATION* Installation Downtime after installation Damage caused by switching the appliance on too soon. This can damage the heat pump. After setting up the tumble dryer, wait for at least one hour before switching it on. Levelling the tumble dryer ... -
Page 61: Room Ventilation
*INSTALLATION* Installation Room ventilation - Air drawn in for use in the drying pro- cess will be warm when it is expelled back into the room. It is therefore very important to ensure the room is ad- equately ventilated, particularly if the dryer is located in a small room. -
Page 62: Hose For External Drainage Of Condensed Water
*INSTALLATION* Installation Drainage options Hose for external drainage of condensed water Tip: Follow the warnings regarding leak- ing or returning water if you select one The condensed water is pumped away of the following connection options. through the drain hose which is loc- - Directed into a floor gully ated at the back of the dryer. - Page 63 *INSTALLATION* Installation Drainage accessories, included Install adapter 1 to the sink drain out- let using nut 2. The nut is usually fitted with a washer which must be removed. Attach the end of the hose 4 to ad- apter 1.
-
Page 64: Electrical Connection
*INSTALLATION* Installation cording to IEC/EN 60947). This con- Electrical connection nection process must be performed by This description applies to tumble dry- a qualified electrician. ers both with and without a mains The plug connector or isolator switch plug. should be easily accessible at all times. The following applies to tumble dryers ... - Page 65 *INSTALLATION* Installation above. If in doubt, please ask your elec- trical distributor for actual impedance value.
-
Page 66: Technical Data
Technical data Height 850 mm Width 596 mm Width (only for appliances with a stain- 605 mm less steel lid) Depth 636 mm Depth with door open 1054 mm Weight 62 kg Drum volume 120 l Load size 8 kg (weight of dry laundry) Hose length 1400 mm Length of mains connection cable 2000 mm Supply voltage See data plate on back of appliance... -
Page 67: Data Sheet For Household Tumble Driers
Technical data Data sheet for household tumble driers In acc. with delegated regulation (EU) No. 392/2012 MIELE Model name/identifier PDR1108HP Rated capacity 8,0 kg Type of tumble drier (Air-vented / condenser) - / ● Energy efficiency class A+++ (most efficient) to D (least efficient) -
Page 68: Eu Conformity Declaration
UK Conformity declaration Miele hereby declares that this heat-pump tumble dryer complies with UK Radio Equipment Regulations 2017, as amended. The complete text of the UK declaration of conformity is available from one of the following internet addresses: - Products, Download from www.miele.co.uk... -
Page 69: Consumption Data
Consumption data Load size Final spin speed Residual Energy Programme moisture running time washing machine Cottons 1000 1.32 1000 0.75 Cottons, 1200 1.20 Cupboard Dry 1400 1.15 1600 1.00 Cottons, Hand iron 1000 0.99 1200 0.85 1400 0.80 1600 0.70 Minimum iron, 1200... -
Page 70: Programmable Functions
Programmable functions Programming You can use the programmable func- tions to alter the dryer's electronics to suit your requirements. Programming is carried out by following these steps (, , ... ) using the sensor controls. Accessing the programming level Prerequisite - The programme selector is turned to a drying programme. - Page 71 Programmable functions Choosing and selecting a program- Programmable functions mable function Factory default The number of the programmable Cottons drying levels function will appear in the time display as and a number: Minimum iron drying levels e.g.
- Page 72 Programmable functions Editing and saving a programmable X = can be selected, = factory default function Confirm the chosen selection with You can either switch a programmable the Start/Add laundry sensor control. function on/off or select different op- tions. The number of the programmable func- tion (e.g. ) will then light up again.
-
Page 73: Factory Default
Programmable functions Factory default Minimum iron drying levels The programmable functions are reset You can adjust the drying levels for the to the factory default settings. Minimum iron programme to one of 7 different levels. = back (without resetting) Options ... -
Page 74: Cooling Down Temperature
Programmable functions Cooling down temperature Buzzer volume The laundry will be cooled to 55 °C be- The buzzer volume can be changed. fore the end of the programme. It can = on, quieter be cooled to a lower temperature, but this will prolong the cooling phase. -
Page 75: Pin Code
Programmable functions PIN code Conductivity The PIN code prevents your tumble This programmable function must only dryer being used without your know- be set if the residual moisture reading ledge. in your laundry is incorrect due to ex- tremely soft water. When the PIN code has been activated, you have to enter the PIN code after Options... -
Page 76: Control Field Switch-Off Behaviour
Programmable functions Control field switch-off be- Memory haviour You can set the memory so that the electronic module saves the selected To save energy, the time display and drying programme along with the re- sensor controls will go out once the quired drying level or a specific option. -
Page 77: Buzzer Active
Programmable functions Buzzer active Airways indicator The buzzer sounds to let you that it is Fluff should be removed after drying. the end of the programme. It can be The indicator light will also come on switched on or off. when there is a certain build-up of fluff in the filters. -
Page 78: Backlight Brightness Dimmed
Programmable functions Backlight brightness Welcome tone dimmed You can decide whether or not a wel- come tone is played when the appli- The brightness of the dimmed sensor ance is switched on. controls in the control field can be set to one of 7 different levels. -
Page 79: Networking
The network configuration has been de- - You will only receive a message when leted. A new connection setup has to be an update is available. carried out in order to use Miele@home again. - Once an update has been installed, it cannot be undone. - Page 80 Programmable functions - Some software updates can only be Postponing the update carried out by the Miele Customer After the tumble dryer is switched on, Service Department. appears on the time display. Activating/deactivating Touch the sensor control.
-
Page 81: Remote Control
Programmable functions Remote control SmartGrid You can use the Miele app to check You can use this function to set your the status of your tumble dryer from tumble dryer to start automatically anywhere and start it remotely. You... -
Page 82: Copyrights And Licences For The Communication Module
These items of software/software components are pro- tected by copyright. The copyrights held by Miele and third parties must be re- spected. Furthermore, this communication mod- ule contains software components which are distributed under open source licence conditions. - Page 83 Tel. +971 4 3044 999, Fax. +971 4 3418 852 Dublin 24 800-MIELE (64353) Tel: (01) 461 07 10, Fax: (01) 461 07 97 E-Mail: info@miele.ae E-Mail: info@miele.ie, Internet: www.miele.ie Website: www.miele.ae Manufacturer: Miele & Cie. KG, Carl-Miele-Straße 29, 33332 Gütersloh, Germany...
- Page 84 PDR 1108 HP SmartBiz en-GB M.-Nr. 12 646 520 / 01...