Page 1
Koninklijke Philips Electronics N.V. or their respective owners. TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
Page 2
Koninklijke Philips Electronics N.V. or their respective owners. TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
Page 3
Koninklijke Philips Electronics N.V. or their respective owners. TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
Page 4
Product specifications are subject to change without notice. - Weight ± 18.44 kg For more specification details of this product, see • with TV stand: www.philips.com/TVsupport Width 1244.2 mm - Height 783.9 mm - Depth 225.2mm - Weight ± 21.29 kg 65HFL6x14U Display Resolution •...
Page 5
–Weight ± 9.1 kg • 1440 x 900 - 60Hz 50HFL6214U • 1600 x 1200 - 60 Hz • without TV stand: • 1920 x 1080 - 60 Hz Width 1115.6mm –Height 653.4mm –Depth80.6mm – • 3840 x 2160 - 60 Hz Weight ±...
Page 6
• Dolby® Audio • Audio out - Optical Toslink • DTS-HD (M6) • VGA - -For 6214/2214/5214 Series • Output power (RMS) : 20W 19HFL5014W/12 Connectivity: • Dolby Audio TV Back • HDMI in - ARC - Ultra HD • Antenna (75 ohm) Connectivity •...
Page 7
Refer to the diversity tables for the correct values. two pins of the Mains/AC Power plug. • The correct component values are listed on the Philips • Check the cabinet for defects, to prevent touching of any Spare Parts Web Portal.
Page 8
• Mix of lead-free soldering tin/parts with leaded soldering tin/parts is possible but PHILIPS recommends strongly to avoid mixed regimes. If this cannot be avoided, carefully clear the solder-joint from old tin and re-solder with new tin.
Page 9
originating from the USA and used e.g. in • Always respect voltages. While some may not be dangerous in themselves, they can cause unexpected LATAM and AP-NTSC countries reactions that are best avoided. Before reaching into a B-TXT Blue TeleteXT powered TV set, it is best to test the high voltage Centre channel (audio) insulation.
Page 10
G-TXT Green TeleteXT distance is 6.5 MHz. L' is Band I, L is all H_sync to the module bands except for Band I High Definition LG.Philips LCD (supplier) Hard Disk Drive Loudspeaker HDCP High-bandwidth Digital Content Protection: LVDS Low Voltage Differential Signalling A “key”...
Page 11
Serial Peripheral Interface bus; a 4-wire module, implementing the CA system for a synchronous serial data link standard host (e.g. a TV-set) S/PDIF Sony Philips Digital InterFace Power On Reset, signal to reset the uP SRAM Static RAM PSDL Power Supply for Direct view LED...
Page 12
Thin Film Transistor toward external amplifier Total Harmonic Distortion Vestigial Side Band; modulation method TMDS Transmission Minimized Differential WYSIWYR What You See Is What You Record: record Signalling selection that follows main picture and Transport Stream sound TeleteXT WXGA 1280 × 768 (15:9) TXT-DW Dual Window with TeleteXT XTAL...
Page 25
3.2 Assembly/Panel Removal 3.2.1 Stand removal 1. Remove the fixation screws [1] that secure the stand. 2. Take the stand bracket out from the set. (2114/5214 Series stand removal) (6114U Series stand removal) 3.2.2 IR board Control Unit 1. Unplug the connector from the SSB. Caution: be careful, as these are very fragile connectors! 2.
Page 26
2.3 Rear Cover Warning: Disconnect the mains power cord before removing the rear cover. 1. Remove all fixation screws [2] and [3] that secure the Back cover assy. 2. Unplug the connector [2] that marked by red box below from SSB. 3.
Page 27
(For 6x14U series) 3.2.4 Keyboard Control Unit 1. Release the connector from the SSB Board. Caution: be careful, the Keyboard is catch on the Back cover, please be careful to avoid damage the fragile connectors! 2. Remove all the fixation screws from the keyboard control panel [2] and take it out from the Back cover. When defective, replace the whole unit.
Page 28
3.2.6 Power Supply Unit (PSU) Caution: it is mandatory to remount all different screws at their original position during re-assembly. Failure to do so may result in damaging the PSU. 1. Gently unplug all connectors from the PSU. 2. Remove all fixation screws from the PSU. 3.
Page 29
4. Service Modes 4.1 Service Modes The Service Mode feature is split into following parts: Service Alignment Mode (SAM). Factory Mode. Customer Service Mode (CSM).SAM and the Factory mode offer features, which can be used by the Service engineer to repair/align a TV set. ...
Page 30
– (De) activate the selected menu item. – (De) activate the selected sub menu. – Change the value of the selected menu item. When you press the MENU button once while in top level SAM, the set will switch to the normal user menu (with the SAM mode still active in the ...
Page 31
How to Activate the Factory mode To activate the Factory mode, use the following method: Press the following key sequence on the remote control transmitter: from the “menu/home” press “1999”, directly followed by the “Back/Return” button. Do not allow the display to time out between entries while keying the sequence. After entering the Factory mode, we can see many items displayed, use the UP/DOWN keys to display the next/previous menu items Factory mode overview How to Exit the Factory mode...
Page 32
CSM Overview How to Navigate By means of the “CURSOR-DOWN/UP” knob (or the scroll wheel) on the RC-transmitter, can be navigated through the menus. How to Exit CSM To exit CSM, use one of the following methods. Press the MENU/HOME button on the remote control transmitter. ...
Page 33
5. Software Upgrading, Error code and Panel Code 5.1 Software Upgrading 5.1.1. The following update is for .pkg file. 1. Rename the file to “upgrade_loader.pkg”. 2. Prepare a USB memory (File format: FLAT, Size: 1G~8G). 3. Copy the software to USB flash disk (root directory). 4.
Page 34
If an error occurs during the update, retry the procedure. If the error reoccurs, contact Philips Consumer Care 1. Connect your USB flash drive (containing the software update) to the USB connector on the TV. Wait 30 seconds or until the USB drive is recognized by the TV.
Page 35
5.2.2 How to Read the Error Buffer You can read the error buffer in following ways: • On screen via the SAM/CSM (if you have a picture). Example: – ERROR: 000 000 000 000 000: No errors detected – ERROR: 013 000 000 000 000: Error code 13 is the last and only detected error –...
Page 36
“Set Option Code” in below tab. After resetting the Display Code, restart the set immediately. Panel ID Set option CTN_ALT BOM# Panel Type code 43HFL6x14U/27 TPT430H3-QUBH10.K SD9P0Q 50BFL2114/27 TPT500B5-U2T01.D S01AY 50HFL6x14U/27 TPT500B5-U1T01.D S03BC 55HFL6x14U/27 TPT550J1-QUBH84.K SD9P0AZ 58BFL2114/27 TPT580B5-U1T01.D S01AJ 65BFL2114/27 TPT650J1-QUBF90.K 9WP0R...
Page 37
Trouble shooting 2016年12月10日 2016/4/8 Picture-related Intermittent Ask Photo Picture ? problem ? Menu Smarkt Signal SW latest ? Backlight? issue function? issue SSB+LVDS+Panel Update SW LED working ? PSU/SSB Problem solved ? Sound ? PSU+ Panel Finish SW+SSB...
Page 38
Trouble shooting 2016年12月10日 2016/4/8 Audio/Sound- related Intermittent Sound ? problem ? Setting SW latest ? Mute ? issue issue Update SW Extra device Check extra connect? device Problem solved ? Factory setting Finish Sound back ? Setting issue SSB+SPK...
Page 39
6.Slow response to user interaction 7.Switches ON by itself 8.Switches Off by itself 9.Stuck in standby mode / unable to start up 10.Stuck on PHILIPS / ANDROID logo 11.CAM not recognized by TV 12.CAM authentication issue 13.Misc CAM issue 14.IP-EPG issues 15.BC-EPG issues...
Page 40
7. Electrical Diagram Block diagram 7.2 Power Supply Power architecture of this platform. AUDIO LVDS Platform power Display power CN8601/CN8602 ON/OFF Platform PS_ON MT5596 12V_A CN701 AC-input + Main filter AC IN...
Page 50
9-1-3 Main Power HS9123 36 KOHM +-1% 1/8W R9103 HEAT SI NK R9100 F o r D 9 1 2 3 R9101 3M 1% 3M 1% R9191 +Vboost H O T C O L D C9102 2.2NF 10% 50V D9123 R9192 2 4 V / 3 .
Page 52
9.2 A 715G9860 PSU(For 50”/58” BFL2114 Series) 9-2-1 AC Input T 5 A H / 2 5 0 V F 9 9 0 1 T5AL/250V F9902 F9901 5A 250V NR9901 F9902 SG9903 NTCR 1R/3.6W SG9901 NC/FUSE DSPL-501N-A21F NC/DSPL-501N-A21F L9901 17mH C9901 RSEN- 22PF 250V...
Page 53
9-2-2 PFC with LD7592GS C9802 L 9 8 0 1 E Q 3 2 1 5 0 W L V / 2 0 0 W 47pF 2KV NR9801 L9802 EQ40 200W LV L9803 EQ25 150W HV D9801 NTCR 3R FMNS-1106S NR9802 Vsin FB9801...
Page 54
9-2-3 Main Power 1 5 0 W u s e T 9 1 0 2 ( n o P a r t I D ) 200W use T9101 380GL52P370H0000VP /12V & 24V C9909 470pF 250V D9107 D9102 FMEN-220A 20A 100V D9101 R9101 R9102...
Page 55
9-2-4 LED L8603 SPS3080-C 30A 80V NC/33uH BEAD FB8602 B o o s t C h o k e O p t i o n 150W LV L8602 373G0253265H00 33UH HV L8602 373G0253365H00 82UH L8601 D8601 BEAD FB8601 33uH 200W +VLED LV L8601 373G0253376X0000VP 33UH HV L8602 373G0253365H00 82UH...
Page 56
9.3 A 715GA018 PSU(For 50”/55”/58” 6x14U & 65BFL2214 & 65HFL5214U Series) 9-3-1 AC Input C9911 220PF 250V SG9901 C9913 F9901 T 5 A H 2 5 0 V DSPL-501N-A21F 470PF 250V 5A 250V F o r B D 9 9 0 1 HS9901 FB9901 NC/HEAT SINK...
Page 58
9-3-3 LLC with SSC3S927 C9181 F o r Q 9 1 0 1 Q 9 1 0 2 NC/2.2nF 50V R9191 R9103 R9101 R9100 R9102 3M 1% 36K OHM 0R05 1/4W 3M 1% H O T C9101 C O L D HS9101 R9192 1000pF 2KV...
Page 71
9-6-3 Main Power R9105 C9909 C9103 470pF 250V 1NF 2KV D9102 D9101 R9101 R9102 1N4148W PG4007 3M 1% 3M 1% R9106 Q9101 IPA50R800CE R9107 R9108 D9107 10 OHM 1% 1/8W 75 OHM 1% 1/8W FMET-22015 C9104 R9104 100pF 2KV H O T C O L D +Vboost NC/20M OHM...
Page 72
9-6-4 BL power L8601 33uH HS8601 D8601 FB8601 FMET-22015 BEAD +VLED L 8 6 0 1 O p t i o n ( L 8 6 0 2 N C ) LV 33UH 373G0253258X00 L8602 HV 82UH 373G0253363H00 NC/80uH C8617 100pF 2KV HEAT SINK +Vboost...
Page 73
9.7 B 715GA841 SSB 9-7-1 Tuner/Demod T u n e r Cl o s e d T u n e r C l o s e d T 5 5 9 6 D i f f e r e n t i a l P a i r TU201 FB214 +3V3_TUNER...
Page 74
9-7-2 HDMI Inputs H D M I 1 C o n n e c t e d p o r t H D M I 2 C o n n e c t e d p o r t C 7 1 1 1 c l o s e p i n H D M I...
Page 75
9-7-3 MT5596 Ethernet/USB T y p e R J 4 5 E t h e r n e t P HY T y p e RJ45_FE_TX+ C7604 C1105 L1101 T7601 60uH NC/100NF 16V NC/S16013 LF NC/10PF 50V L1102 TXP0 C1106 100NF 16V ETHERNET-TXp R7798...
Page 76
9-7-4 MT5596 HDMI/ARC C l e a r a n c e t r a c e w i d t h f o r a l l S C L a n d S D A H D M I T M D S s i g n a l s Differential 100 Ohm nets...
Page 77
9-7-5 MT5596 IF/I2S/Audio U401-5 TER-IFp-SOC TER-IFp-ANA R7524 0.05R TER-IFp-SOC ADCINP_DEMOD HSY NC TER-IFn-SOC TER-IFn-ANA R7527 0.05R TER-IFn-SOC ADCINN_DEMOD VSY NC C7525 C7526 NC/47pF 50V NC/47pF 50V VGA_SDA VGA_SCL C l o s e M T 5 5 9 6 COM1 PB1P PR1P AGC-ANA-SOC...
Page 78
9-7-6 MT5596 TS/GPIO U401-8 DEMOD_RST G P I O 0 DEMOD_RST CI_A0 DEMOD_RST TSOUT_CLK CI_A1 G P I O 1 DEMOD_TSCLK TSOUT_CLK TSOUT_D0 CI_A2 G P I O 2 DEMOD_TSDATA0 TSOUT_D0 TSOUT_D1 G P I O 3 CI_A3 DEMOD_TSDATA1 TSOUT_D1 TSOUT_D2 G P I O 4 TSOUT_D2...
Page 79
9-7-7 MT5596 EMMC/I2C F o r c o d e d o w n l o a d , d e b u g g i n g , factory alignment and compair mode. I 2 C - S S B D E B U G +3V3-STANDBY A d d...
Page 80
9-7-8 MT5596 VB1/KEY_IR M T 5 5 9 6 V x 1 O u t p u t V - B Y - 1 O u t p u t D i s p l a y U401-3 CN403 CONN 51P SOC-VB1-TX7P TP3758 SOC-VB1-TX7N...
Page 81
9-7-9 MT5596 DDR3-1-2 M T 5 5 9 6 D D R 3 2 b D D R 3 # 1 D D R 3 # 2 D D R 3 - 1 8 6 6 4 G b D D R 3 - 1 8 6 6 4 G b DDRV DDRV...
Page 82
9-7-10 MT5596 DDR3-3-4 M T 5 5 9 6 D D R 3 2 b D D R 3 # 3 D D R 3 # 4 D D R 3 - 1 8 6 6 4 G b D D R 3 - 1 8 6 6 4 G b DDRV DDRV...
Page 83
9-7-11 MT5596 DDR3-5 M T 5 5 9 6 D D R 1 6 b D D R 3 # 5 D D R 3 - 1 8 6 6 4 G b DDRV U401-13 CRA0 CRDQM0 CRA0 CRDQM0 CRA1 CRDQS0 MTP273 CRA1...
Page 84
9-7-12 MT5596 VCCK/DVSS U401-11 +1V0-VCCK +1V0-VCCK U401-12 DVSS DVSS DVSS DVSS AA15 AC25 AA25 DVSS DVSS VCCK VCCK AA16 AC26 AA26 DVSS DVSS VCCK VCCK AA17 AC27 AA27 DVSS DVSS VCCK VCCK AA18 AD20 AB25 DVSS DVSS VCCK VCCK AA19 AD21 AB26 B o t t o m...
Page 85
9-7-13 Audio Amp/HP/SPDIF +12V-AUDIO C l o s e T A S5 7 6 0 L D (in the sam e order) +3V3 +3V3-AUDIO1 R5111 C5101 C5104 C5102 C5107 C5113 C5122 C5118 R5110 C5112 220uF 16V 220uF 16V 4.7uF 16V 4.7uF 16V 1UF 25V 100NF 16V...
Page 86
9-7-14 System Power-1 P o w e r I n p u t T o P S U Main_12V Main_12V C4323 CN701 ZD701 100NF 16V +5V-SW +3V3 +3V3 RLZ15B AU_12V AU_12V AU_12V R4307 R4306 R4310 NC/2.2K NC/10K 5% NC/4.7K R4316 100 OHM R4318 100 OHM...
Page 87
9-7-15 System Power-2 + 1 2 V + 5 V - S W R1724 120K 5% +12V U1701 R1730 C1711 0R05 1/4W C1715 C1721 C1713 C1714 4.7uF 16V 10UF 16V 100NF 16V 100NF 16V R1729 +5V-SW NC/4.7uF 16V 2.2R 1% L1701 +12V 2.2uH...
Page 88
9-7-16 HTV Function +3V3 +3V3-STANDBY B a t h r o o m S p e a k e r 1 2 V O u t p u t C u r r e n t P r o t e c t i o n R306 R307 NC/10K 5%...
Page 91
9.9 E 715GA039 IR Board (For HFL6114U & BFL2214 & 50” /55” HFL5214 Series) 9-9-1 IR&STB LED&Light sensor L i g h t S e n s o r DVD3V3 U222 R 2 2 3 R 2 2 4 R 2 2 5 R 2 2 6 R 2 2 7 R 2 2 8...
Page 92
9.10 E 715GB499 IR Board (For HFL6214U & 43” HFL5214 Series) 9-10-1 IR&STB LED&Light sensor L i g h t S e n s o r DVD3V3 U222 DVD3V3 C222 JSA-1136 C221 100N 16V 1uF 16V R221 R222 B o t t o m 10K 5% 10K 5% LS_SCL...
Page 93
9-10-2 Key/AL interface Y S T I C K C231 100PF 50V Joystick diversity for AL TACT SW 6P SW231 C N 2 4 1 C N 2 4 2 C 2 4 1 C 2 4 2 R241 R 2 4 2 R 2 4 3 R 2 4 4 Ri g h t...
Page 94
9.11 E 715G9740 Keyboard control panel (For 50” /58”/65” BFL2114 Series) 9-10-1 Key...
Page 112
Koninklijke Philips Electronics N.V. or their respective owners. TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
Page 113
Product specifications are subject to change without notice. - Weight ± 18.44 kg For more specification details of this product, see • with TV stand: www.philips.com/TVsupport Width 1244.2 mm - Height 783.9 mm - Depth 225.2mm - Weight ± 21.29 kg 65HFL6x14U Display Resolution •...
Page 114
11. Dismantling procedure for specific handling parts As complete appliances, LCDs are deemed to be hazardous waste (e.g. 16 02 13*, 20 01 35*) in the EU according to the German Waste Catalogue Ordinance. These appliances may only be handled by authorized handling plants. LCDs must be stored in accordance with the requirements stipulated in Appendix VIII (1) or (2) of Directive 2012/12/EU and must, amongst other things, be stored in a weatherproof manner.
Page 115
These substances, mixtures and components shall be disposed of or recovered in compliance with Directive 2008/98/EC cathode ray tubes: the fluorescent coating has to be removed equipment containing gases that are ozone depleting or have a global warming potential (GWP) above 15, such as those contained in foams and refrigeration circuits: the gases must be properly extracted and properly treated.
Page 116
can be removed with appropriate tools. The panel consists of several plastic sheets which can be processed. A final consideration is that of the back light which must be removed prior to processing. These may be present along either the bottom, or either side of the display as a strip of lights.