Advertisement
Quick Links
Advertisement
Related Manuals for Philips T-Line 5000 Series
Summary of Contents for Philips T-Line 5000 Series
- Page 1 Interactive Display 5000 Series 10BDL5051T User Manual (English) www.philips.com/ppds...
- Page 2 10BDL5051T Table Of Contents Warranty policy for Philips Professional Display Solutions .................44 Index ..................46 Safety Instructions ............1 Unpacking and Installation ......... 7 2.1. Package Contents ..........7 2.2. Installation ............8 2.2.1. Connecting the power cable .... 8 2.2.2. Connecting the network cable ..8 2.2.3.
- Page 3 When turning off the display by detaching the power cord or DC power cord, wait 6 seconds before re-attaching the power cord or DC power cord for normal operation. • Ensure the use of an approved power cord provided by Philips at all times. If your power cord is missing, please contact your local service center. • Do not subject the display to severe vibration or high impact conditions during operation.
- Page 4 10BDL5051T Service: • The casing cover should be opened only by qualified service personnel. • If there is any need for repair or integration, please contact your local service center. • Do not leave your display under direct sunlight. If your display does not operate normally, having followed the instructions set out in this document, please contact a technician or your local service center.
- Page 5 10BDL5051T Federal Communications Commission (FCC) Notice (U.S. Only) NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Use only an RF shielded cable that was supplied with the display when connecting this display to a computer device. To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture.
- Page 6 10BDL5051T Waste Electrical and Electronic Equipment-WEEE Attention users in European Union private households This marking on the product or on its packaging illustrates that, under European Directive 2012/19/EU governing used electrical and electronic appliances, this product may not be disposed of with normal household waste. You are responsible for disposal of this equipment through a designated waste electrical and electronic equipment collection.
- Page 7 10BDL5051T NOTICE SOFTWARE END USER LICENSE AGREEMENT THIS SOFTWARE END USER LICENSE AGREEMENT (THIS “AGREEMENT”) IS A LEGAL AND BINDING AGREEMENT BETWEEN YOU (EITHER AN INDIVIDUAL OR ENTITY) AND MMD MONITORS & DISPLAYS NEDERLAND B.V., A DUTCH LIMITED LIABILITY COMPANY, WITH ITS PRINCIPAL OFFICE AT PRINS BERNHARDPLEIN 200, 1097 JB AMSTERDAM, THE NETHERLANDS AND ITS SUBSIDIARY COMPANIES (INDIVIDUALLY AND COLLECTIVELY "MMD"). THIS AGREEMENT GIVES YOU THE RIGHT TO USE CERTAIN SOFTWARE (THE “SOFTWARE”) INCLUDING USER DOCUMENTATION IN ELECTRONIC FORM WHICH MAY HAVE BEEN PROVIDED SEPARATELY OR TOGETHER WITH A MMD PRODUCT (THE DEVICE”). BY DOWNLOADING, INSTALLING OR OTHERWISE USING THE SOFTWARE, YOU ACCEPT AND AGREE TO BE BOUND BY ALL OF THE TERMS AND CONDITIONS OF THIS AGREEMENT. IF YOU DO NOT AGREE TO THESE TERMS AND CONDITIONS, DO NOT DOWNLOAD, INSTALL OR OTHERWISE USE THE SOFTWARE. IF YOU ACQUIRED THE SOFTWARE IN TANGIBLE MEDIA E.G. CD WITHOUT THE OPPORTUNITY TO REVIEW THIS LICENSE AND DO NOT ACCEPT THESE TERMS, YOU MAY RECEIVE A FULL REFUND OF THE AMOUNT, IF ANY, THAT YOU PAID FOR THE SOFTWARE IF YOU RETURN THE SOFTWARE UNUSED WITH PROOF OF PAYMENT WITHIN 30 DAYS FROM THE DATE OF PURCHASE. 1. Grant of License. This Agreement grants you a non-exclusive, nontransferable, non-sub licensable license to install and use, on the Device, one (1) copy of the specified version of the Software in object code format as set out in the user documentation solely for your personal use. The Software is "in use" when it is loaded into the temporary or permanent memory (i.e. RAM, hard disk, etc.) of the Device.
- Page 8 10BDL5051T 8. Support Services. MMD is not obligated to provide technical or other support (“Support Services”) for the Software. If MMD does provide you with Support Services, these will be governed by separate terms to be agreed between you and MMD. 9.
- Page 9 10BDL5051T Unpacking and Installation Before installing the display • This product is packed in a carton, together with the standard accessories. • Any other optional accessories will be packed separately. • After opening the carton, ensure that the contents are complete and in good condition. 2.1.
- Page 10 10BDL5051T 2.2. Installation Securing the power and network cable 2.2.1. Connecting the power cable 1. Connect the power adapter’s connector into the display’s power input socket. 2. Insert the matching AC plug fully into the power adapter. 3. Plug the AC plug of your power adapter into an electric outlet to power on the device. 2.2.2.
- Page 11 10BDL5051T 2.2.4. Mounting and installation Mounting Option 1: [VESA mount] Supporting VESA standard: VESA MIS-D75 (75*75mm) Supporting screw: M4*9mm (exclude the mounting plate thickness) The equipment and its associated mounting facilities still remain secure during the test. Use only the UL listed VESA mount with a minimum weight/load of the weight of the unit without base. * Installation height: <2 m...
- Page 12 10BDL5051T Mounting Option 2: [Using back cover] (4). Use screws to secure the back shell trim to the wall. Supporting screw: Self-tapping screw*5pcs (exclude the mounting plate thickness) (1). Use a screwdriver to loosen the screw on the back cover. (5). Plug in the cable. (2).
- Page 13 10BDL5051T Physical view and features 3.1. Left View Menu: To activate the OSD menu. Volume +/-: Volume up and down. Operation Function Menu + Volume- Launch Admin mode app Menu + Volume+ Launch Quick Information app Menu + Menu + Volume+ + Volume- + Volume- + Enable touch function Volume+ Menu + Menu + Volume- + Volume- Turn on the screen...
- Page 14 10BDL5051T 3.2. Input/Output Terminals Micro SD Insert a Micro SD card. Micro USB Insert a USB storage device. Earphone Connect to an earphone through this 3.5 mm Ear Jack (CTIA standard). HDMI OUT HDMI video/audio output. USB C2 For adb debugging. DC IN Connect to the DC power adapter. * LAN control function for the use of remote control signal from control center. * PoE+ (power over Ethernet): 24W Status Green...
- Page 15 Start button. 4.1.3. Clone Media Files into internal Clone media files from the selected source storage to target storage. System clone files under the following list of folder: Note: After entering OOBE, the Signage Display Name will be (1) philips/photo set to the default value: “PD” + Ethernet Mac Address. (2) philips/music (1). Support Language (3) philips/video The system supports 22 languages and requires users to (4) philips/pdf set it during the first boot.
- Page 16 If you prefer not to set up this item, you can skip it using the Skip button. (1). Import Signage Settings from SD / USB Import data from “philips/clone/10BDL5051T-clone.7z” located in SD card or USB. The import action will be executed when leaving OOBE.
- Page 17 10BDL5051T (1). Wireless (Wi-Fi) (1). Import Signage Display Settings Complete After connecting to the Wi-Fi network, you will be After pressing Finish, if “Import Signage Settings from SD / automatically directed to the next page. USB” is configured, the system will automatically reboot after completion. (2). Ethernet (2). Manual Setup Complete After completing the Ethernet connection, you will be automatically directed to the next page.
- Page 18 10BDL5051T 4.2. Android Launcher 4.2.1. Android PD launcher • Android PD launcher is a black page as shown below: (1). Settings page • Exit the App by pressing the “Back” key and the screen will enter Android PD launcher. 4.2.2. Admin mode •...
- Page 19 10BDL5051T Wi-Fi page (6). Power page User can press the “Power off” button to shutdown device or press the “Reboot” button to reboot device, or press the “Sleep” to sleep device. User can press “Menu + Menu + Volume - + Volume-” to wakeup device. Ethernet page For the always-on model, like 10BDL5051T, the “Power off” button is not designed to completely shut down the device. When the user presses the “Power off” button, the device will go through a graceful shutdown process until it displays the “Unplug power cord”...
- Page 20 10BDL5051T 4.3. Setting UI 4.3.1.1.1. Wi-Fi Enable Wi-Fi Enter PD settings by clicking “Settings” icon in Admin mode. Enable/disable Wi-Fi connection through main switch in Setting -> Network & Internet -> Wi-Fi -> Off/On toggle button. (1). Wi-Fi Off Setting menu consists of the following items: (1). Network & internet (2). Connected devices (3). Signage Display (2).
- Page 21 10BDL5051T DHCP You must input network SSID, security type and other advanced options for this network. The IP Address, Netmask, DNS Address and Gateway settings are assigned by DHCP server, they are not modifiable. If connection is successful, it will show current network settings. Note: When Wi-Fi is enabled, Ethernet will be disabled automatically. Network preferences Static IP User can assign device’s IP Address, Netmask, DNS address and Gateway settings of Ethernet in Static IP connection...
- Page 22 10BDL5051T 4.3.2. Connected devices 4.3.3.1. General Settings The “Connected devices” option is used to manage and view other devices connected to your Android device, including Bluetooth and NFC devices. These settings help users easily pair, manage, and configure various external devices, enhancing the user experience and convenience. 4.3.3.1.1.
- Page 23 10BDL5051T 4.3.3.1.3. Boot Logo 4.3.3.1.4. Boot on source User can set up device boot up logo (boot animation) when Choose to select a source when booting up. Settings -> Signage Display -> General Settings -> Boot Logo is set to “User” mode. Input: Select input source when booting up. If Logo not set to “User” mode, user cannot select custom boot animation.
- Page 24 10BDL5051T Please note that if user chose “Custom app” as boot on source, the user specified application (APK) must be selected in Settings -> Signage Display -> Source Settings -> Custom APP. 4.3.3.1.5. Schedule Allow user setup up to seven different scheduled intervals of display activity. After enabling this feature, you can set the interval time between each screenshot, as well as the destination folder where the captured screen will be saved. The option “Save to” notifies you that the screenshot images will be saved to the internal storage and they cannot be changed manually.
- Page 25 (5). Save to The screen images will be saved in the folder “philips/ screenshot” of the internal storage. (6). Purge Screenshots Set the interval time for deleting the screenshot images.
- Page 26 10BDL5051T 4.3.3.2. Server settings 4.3.3.2.1. Email Notification Click checkbox to enable/disable E-mail notification feature. Set SMTP and manager E-mail after enabling the E-mail notification feature. Other: SMTP Setup sender E-mail address and SMTP server information. There are two types of SMTP server for user set up: “Gmail” and “Other”. By using “Other” option, user can manually setup STMP server, security type and server port. Note: 1.
- Page 27 10BDL5051T Step 1 - Select “2-Step Verification” If 2-Step Verification is not turned on, click it to enable it. Step 3 - Use your Phone to Complete Configuration Use on-screen instructions and available options to complete 2-Step verification using your phone. Step 2 - Configure 2-Step verification Click the “GET STARTED” button to start configuring the 2-step verification options. You may be prompted to log in to your Google Account again to confirm it’s you:...
- Page 28 10BDL5051T Step 4 - Create the App Password Click on the “App Password” option to create a new application password: Manager Email Step 5 - Add New App Name Specify the destination address to receive the e-mail. First, select a device (for example, Windows Computer) and then click on “Select App” menu and choose “Other (custom name)”: Test To check if your e-mail settings are correct, select ‘Send Test Mail” to send a test e-mail.
- Page 29 10BDL5051T 4.3.3.3. Source Settings d. Port: The port number for the FTP server is available in the range from 1025 to 65535, the default setting is 2121. The User can configure source APK’s detail options. following port number cannot be used: 8000 / 9988 / 15220 / 28123 / 28124 and SICP network port (default 5000).
- Page 30 10BDL5051T 4.3.3.3.3. PDF Player Buttons: (1). FORGET Open PDF Player APK’s edit play list activity and edit effect settings activity. Clear custom source application. It turns gray if custom source application is not set. (2). CANCEL Cancel and close the dialog. (3). SAVE Click SAVE to choose selected APK as custom source application.
- Page 31 1. P ort number ranges from 1025 ~ 65535. • 2. The following ports are occupied, they cannot be assigned to SICP network port: 8000, 9988, 15220, 28123, Clear philips/ folder in internal storage, USB and SD card. 28124 and FTP port (default 2121). • Internal Storage Clear philips/ folder in internal storage only.
- Page 32 (internal storage, USB storage and SD card). Note: If the selected storage (internal storage, USB or SD card external storage) does not contain philips/folder, the system will create it automatically. All available storage medium are listed for user to select.
- Page 33 10BDL5051T • Clone Media Files Clone media files from the selected source storage to target storage. (1). System clone files under the following list of folder: a. philips/photo b. philips/music c. philips/video d. philips/pdf e. philips/browser • Import Signage Display Settings Import database data from philips/clone/10BDL5051T-clone.7z file of selected storage (internal Storage, USB storage and SD card). System imports following data in ZIP file: (1). Import Database in 10BDL5051T-clone.7z (2). Import 3rd party APK in 10BDL5051T-clone.7z All available storage medium are listed (internal storage, USB and SD card).
- Page 34 10BDL5051T • Modify Password • Reset Password User can change the password for login Admin Mode. Follow Reset the password to default “1234”. If succeed, you will see a the steps below: “Successful” toast message. Enter the current password first. Default password is “1234”. 4.3.3.5.8. Touch Click the checkbox to lock or unlock the touch screen. To enable the touch press: 2x Menu button, 1x Vol up, 2x Vol down, 1x Vol up.
- Page 35 USB or internal storage automatically. The fisrt priority is USB storage. if there are no any connected usb devices on PD, all data will then saved into internal storage. The saved path will be {roor directory of USB storage}/ philips/ Log/10BDL5051T-Log-{ yyyy-MM-dd-HH-mm-ss } Or {root directory of internal storate}/ philips/ Log/10BDL5051T-Log-{ yyyy-MM-dd-HH-mm-ss }...
- Page 36 10BDL5051T 4.3.6.1. Brightness level The adjust bar will be show on top of the screen. Drag adjust bar to set brightness. 4.3.6.2. Font size Adjust system default font size by dragging the slide bar. 4.3.6.4. Auto-rotate screen Turn On/Off to switch the rotation settings: 1. Turn On : Rotate the contents of the screen 2.
- Page 37 10BDL5051T 4.3.6.5. Screen saver 4.3.6.6.1. Turn on HDMI Enable the screen saver by toggling the main switch in Settings Turn on/off the HDMI output. -> Display -> Screen saver. The user can choose a screen saver mode: Colors, Photo Frame, or Photo Table. 4.3.6.6.2. Resolution Set the HDMI output resolution. The supported resolutions for the HDMI monitor will be displayed in the selection dialog. Depending on the monitor’s EDID, the resolution list may vary for different monitors. Please note that the output content matches the panel content, so the content will be scaled up or down to fit the HDMI output resolution. The optimal resolution...
- Page 38 10BDL5051T 4.3.6.6.4. System Direction 4.3.8.2.1. Device admin apps User can fix device rotation screen content and HDMI output A list showing the app that supports admin-related operations direction. and controls. 4.3.7. Accessibility Accessibility services are apps that can help users with disabilities or special needs to interact with their Android device more easily. In the Downloaded apps menu, you can view all the accessibility apps that are installed on the device, and enable 4.3.8.2.2.
- Page 39 10BDL5051T 4.3.9.1. Languages & input (2). On-Screen keyboard Let user sets default software IME (Virtual keyboard) and control detail IME settings. The Japanese IME will be installed automatically when user select Japanese language in OOBE. (3). Physical keyboard Let user controls physical keyboard and detail keyboard settings. 4.3.9.1.1. Language The “uinput-key” is system level keyboard for remote control; it will always be present on the keyboard list. 4.3.9.1.2.
- Page 40 10BDL5051T 4.3.9.2.1. Time zone 4.3.9.3. Developer options Let user chooses the time zone Android system developer options for engineer development. 4.3.10. About Following information shows in about page: (1). Legal information (2). Model (3). Android version (4). Up time (5). Build number 4.3.9.2.2.
- Page 41 10BDL5051T 4.3.10.2. Model 4.3.10.3. Android version...
- Page 42 10BDL5051T Appendix 5.2. File manager app 1. The purpose of this software is to offer file browsing, copying, moving, and installing apps, but it cannot ensure 5.1. Advanced features that all files can be opened. (1). Install custom APK 2. Home page will list internal storage, SD card and USB You can use file-manager apk to install it. Please use key storages. The external storage device must be named in combination “Power+ Volume-” to enter “launch admin mode” English or by UTF-8. page. click all app -> launch file manager app -> choose the apk to install (2).
- Page 43 10BDL5051T 5. Select Copy or Move option, it will popup destination 8. In Select Mode, press up or down key to move and press OK dialog. key to select multiple items. 6. Select target storage, the bottom of screen will show 9.
- Page 44 10BDL5051T Cleaning and Troubleshooting 6.1. Cleaning Caution When Using the Display • Be sure to disconnect all cables before moving the monitor. Moving the monitor with its cables attached may damage the cables and thus cause fire or electric shock. • Disconnect the power plug from the wall outlet as a safety precaution before carrying out any type of cleaning or maintenance procedure.
- Page 45 10BDL5051T Technical Data 7.1. Specifications Display: Item Specifications Screen Size 10.1” Number of pixels 1280 (H) x 800 (V) Brightness (typical) 310 cd/m Viewing angle 160/160 In/Out Terminals: Item Specifications VIDEO HDMI x1 (with HDCP) Input Signal RJ45 Ethernet port VIDEO HDMI x1 Output Signal AUDIO Earphone out Internal Speaker 2W + 2W Touch panel Yes (Capacitive 10 points)
- Page 46 (e.g. in the intended environment). For these product categories, a partner company of Philips is the warrantor of the product. Please check the documentation supplied with your product.
- Page 47 To Obtain Warranty Service And Information For detailed warranty coverage information and additional support requirement and help line, please contact the seller and/ or system integrator you purchased the product from. Please note in the USA, this limited warranty is only valid for Products purchased in the Continental United States, Alaska, and Hawaii. Before Requesting Service Please check your user’s manual before requesting service. Adjustments of the controls discussed there may save you a service call. WARRANTY PERIOD Warranty period for PHILIPS signage display is listed as below, for areas not covered in this table, please follow their warranty statement. Standard warranty period for PHILIPS signage display is listed as below, for areas not covered in this table, please follow the local warranty statement. Region Standard Warranty Period USA, Canada...
- Page 48 Installation 8 Left View 11 Operation 13 Package Contents 7 Physical view and features 11 Safety Instructions 1 Setting menu 18 Setup wizard 13 Specifications 43 Technical Data 43 Troubleshooting 42 Unpacking and Installation 7 Warranty policy for Philips Professional Display Solutions...
- Page 49 This product has been manufactured by and is sold under the responsibility of Top Victory Investments Ltd., and Top Victory Investments Ltd. is the warrantor in relation to this product. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license.