Compaq 230050-001 - StorageWorks NAS B3000 Model N900 Server Rack Installation Instructions
Nas b3000 - rack installation instructions
Hide thumbs
Also See for 230050-001 - StorageWorks NAS B3000 Model N900 Server:
- Quick start manual (70 pages) ,
- Installation manual (28 pages) ,
- Quick reference manual (4 pages)
Table of Contents
Advertisement
Quick Links
StorageWorks by Compaq
NAS B3000
Rack Installation Instructions
Open Card Completely Before
Beginning Installation Procedures
NOTICE
© 2002 Compaq Information Technologies Group, L.P.
Compaq, the Compaq logo, and StorageWorks are trademarks of
Compaq Information Technologies Group, L.P.
All other product names mentioned herein may be trademarks of their
respective companies.
Compaq shall not be liable for technical or editorial errors or omissions
contained herein. The information is provided "as is" without warranty
of any kind and is subject to change without notice. The warranties for
Compaq products are set forth in the express limited warranty statements
accompanying such products. Nothing herein should be construed as
constituting an additional warranty.
Printed in the U.S.A.
Important Safety Information
Before installing this product, read the Important Safety
Information document provided.
StorageWorks NAS B3000 by Compaq
Rack Installation Instructions
First Edition (February 2002)
Part Number: 259123-001
Compaq Computer Corporation
259123- 001
1
6
7
8
Identify the device and storage enclosure components.
Item
Description
Device
Power cords for device power supplies
Remote Insight Lights-Out Edition board power cable and adapter
"Y" cable for Remote Insight Lights-Out Edition board
Fiber cables
Rack-mounting hardware for the device
Storage enclosure
Power cords for storage enclosure power supplies
Rack-mounting hardware for the storage enclosure
WARNING: To reduce the risk of personal injury or damage to the
equipment, at least two people are needed to safely remove each
component from the shipping carton.
Installation Tips
Begin installing rack components at the bottom of the rack or
immediately above a previously installed component, and then
work toward the top of the rack.
Have a Phillips screwdriver and a pencil available before
beginning the procedure.
Do not tighten the rack-mounting rail screws completely until
after the component is inserted into the rack. The small amount
of play helps position the rails to the exact width of the
component being installed.
2
4
3
5
9
Advertisement
Table of Contents
Related Manuals for Compaq 230050-001 - StorageWorks NAS B3000 Model N900 Server
Summary of Contents for Compaq 230050-001 - StorageWorks NAS B3000 Model N900 Server
- Page 1 All other product names mentioned herein may be trademarks of their respective companies. Fiber cables Compaq shall not be liable for technical or editorial errors or omissions Rack-mounting hardware for the device contained herein. The information is provided “as is” without warranty of any kind and is subject to change without notice.
- Page 2 Because higher ground-leakage currents are associated with connecting several pieces of equipment to the same power source, Compaq recommends using a power distribution unit WARNING: This product is very heavy. To reduce the risk of personal (PDU) that provides a supplementary ground conductor.
- Page 3 Installing the Storage Enclosure into the Rack For round-hole rail racks only: a. Secure two alignment clips on the front of each rack- mounting bracket. Identify the storage enclosure rack-mounting hardware. b. Secure one alignment clip on the rear of each rack- mounting bracket.
- Page 4 Repeat the above procedure for the opposite side. Label and remove all hard drives. IMPORTANT Compaq recommends that you label each drive to indicate its original slot. Doing this enables you to replace the drives into their original slots after installing the storage enclosure into the rack.
- Page 5 Remove the I/O module/Environmental Monitoring Unit Replace the hard drives. (EMU). CAUTION: You must insert a hard drive or a drive "blank" into each drive bay. If you have an unoccupied drive bay, the storage enclosure quickly overheats when it is powered up. Remove the power supplies.
- Page 6 Installing the Device into the Rack NOTE: For easier installation of the rack-mounting bracket, secure the outer bracket rail to the rack-mounting bracket before securing the rack-mounting bracket assembly to the rack. The joined rack-mounting bracket and bracket rail can be fastened to the rack as one assembly.
- Page 7 Insert the cage nuts into the rack rails and use the fitting tool to pry the cage nut into position. b. Secure the outer bracket rail to the rack-mounting bracket with an 8-32 x 1/4-inch slotted screw. IMPORTANT Do not tighten screws until all three screws have been lined up on the assembly.
- Page 8 WARNING: To reduce the risk of personal injury or damage to the equipment, at least two people are needed to safely load the device Attach the handle to the sides of the NAS B3000. onto the rack. WARNING: To reduce the risk of injury, remove the hot-plug power supplies and all the hard drives before loading the device onto the rack to reduce the weight of the device.
-
Page 9: Storage Enclosure
VHDC SCSI knockouts (2) Storage Enclosure Rear View The device rack installation is complete. Number Connector Connecting the Device and the Global service indicator Storage Enclosure External port Port link indicators (2) Device Rear Panel Connectors RS-232 DB-9 serial port RJ-45 Ethernet connector Power supply/blower assemblies Power supply/blower assembly indicators... - Page 10 IMPORTANT Do not connect the storage enclosure until the SAN connection Connect the Remote Insight Lights-Out Edition board power cord wizard has completed. For instructions concerning the fiber connections, refer to and the adapter to the power port. the Connection Poster. Connect the HBA to the designated port on the switch using a Connect the monitor to the video port on the Remote Insight fiber cable.
-
Page 11: Regulatory Compliance Notices
For instructions on configuring the system, refer to the StorageWorks NAS B3000 by Compaq Quick Reference poster. · Reorient or relocate the receiving antenna. -
Page 12: Declaration Of Conformity - United States Only
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For questions regarding this declaration, contact: Compaq Computer Corporation P.O. Box 692000, Mail Stop 510101 Houston, Texas 77269-2000 Or call 281-514-3333 To identify this product, refer to the series number found on the product.