Operating instructions for dishwashers To avoid the risk of accidents or en - GB damage to the appliance, it is essential to read these instructions as well as the installation plan before it is installed and used for the first time. M.-Nr.
Description of the appliance Appliance overview a Upper spray arm (not visible) g Filter combination b Cutlery tray (depending on model) h Data plate c Upper basket i Rinse aid reservoir d Middle spray arm j Dual compartment detergent dispenser e Air inlet for drying k Salt reservoir (depending on model)
This instruction book applies to several different dishwasher models. The specific dishwasher models below are referred to as follows: G 1182 etc. = G 1XXX G 2182 etc. = G 2XXX The model numbers G 1XXX and G 2XXX used in this book refer to the model designation specified on the data plate of the appliance (and not the description on the control panel).
Warning and Safety instructions Safety with children This appliance conforms to current This appliance is not a toy! To avoid safety requirements. Inappropriate the risk of injury, keep children well use can, however, lead to personal away and do not allow them to play in injury and damage to property.
Page 8
Warning and Safety instructions Technical safety Do not connect the dishwasher to the mains supply until it has been fully Before setting up the appliance, installed. check it for any externally visible damage. Under no circumstances Before connecting the appliance, should you use a damaged appliance.
Page 9
If the connection cable is damaged where necessary. it must be replaced with a Miele cable – The stopcock has been turned off by a Miele approved service technician when the appliance is not used for a only.
Warning and Safety instructions Installation Correct use The dishwasher must be installed Do not use solvents in the and connected in compliance with the dishwasher. Danger of explosion. installation diagram supplied. Do not inhale or ingest dishwasher The dishwasher must be correctly detergent.
Page 11
Warning and Safety instructions Accessories Inadvertently filling the salt reservoir with powder or liquid dishwasher Only use genuine Miele spare parts detergent will damage the water and accessories with this appliance. If softener. Make sure you have picked spare parts or accessories from other...
Caring for the environment Disposal of the packing Disposal of your old appliance material Electrical and electronic appliances often contain materials which, if The transport and protective packing handled or disposed of incorrectly, has been selected from materials which could be potentially hazardous to are environmentally friendly for disposal human health and to the environment.
Caring for the environment Energy saving washing This dishwasher is exceptionally economical in its use of water and electricity. You can make the most of your appliance by following these tips: ^ If your household water system is suitable, this dishwasher can be connected to a hot water supply for further economies.
Before using for the first time To open the door To close the door ^ Push the baskets right in. ^ Then lift the door upwards and push until it clicks into position. ^ Pull the handle. If the door is opened during operation all functions are automatically interrupted.
Before using for the first time Water softener The dishwasher is set at the factory for a hardness level of In order to achieve good cleaning 2.2 - 2.7 mmol/l (12 - 15 °d). results, the dishwasher needs to operate with soft water. Hard water If this setting corresponds to the results in the build-up of calcium hardness of your water you do not need...
Before using for the first time To programme the water hardness The number of times the upper right hand programme indicator flashes tells level you the water hardness level which has Each time a button is pressed, one of been set (see chart). the indicator lights will flash and light up in the control panel.
Before using for the first time Checking the programmed water hardness level ^ Switch the dishwasher off with the Off button V. ^ Press the programme selector button in, and whilst holding it in switch the dishwasher on using the On button U .
– Rinse aid formulated for domestic to the water hardness level in your dishwashers. area. Miele branded products are available from the Miele Spare Parts Important! Before filling the salt Department or via the internet at reservoir with dishwasher salt for the www.miele-shop.com.
Before using for the first time ^ Remove the lower basket and Salt indicator unscrew the salt reservoir cap. ^ Fill the salt reservoir with dishwasher salt when the salt indicator light Water or saline solution will run out comes on. (If it comes on during a of the reservoir when the cap is programme, wait until the end of the removed.
Before using for the first time Rinse aid If you only ever use combination Rinse aid is necessary to ensure water products containing rinse aid in your does not cling and leave marks on dishwasher, you do not need to add crockery during the drying phase and rinse aid.
Before using for the first time Rinse aid indicator When the light comes on the reservoir contains sufficient rinse aid for 2 - 3 programmes only. ^ Add rinse aid in plenty of time. ^ Add rinse aid only until it is visible in the opening.
Before using for the first time Setting the rinse aid dosage The upper right hand programme indicator will flash briefly three times at You can adjust the rinse aid dosage for intervals. best results. This means that approx. 3 ml of rinse The rinse aid dosage can be set from aid will be used per programme approx.
Loading the dishwasher Note – Wide based items should be placed at an angle so that water can run off Remove coarse food residues from them freely. crockery. – The spray arms must not be blocked There is no need to rinse items under by items which are too tall or hang running water.
Loading the dishwasher Items not suitable for We recommend: dishwashers: – When purchasing new crockery and cutlery, make sure they are – Wooden cutlery and crockery or dishwasher-proof. items with wooden parts: these may discolour and fade. The glue used in –...
Loading the dishwasher Upper basket Hinged cup rack ^ To make room for tall items, raise the For safety reasons, do not rack upwards. operate the dishwasher without the upper and lower baskets in place. Positioning rail (depending on model) Glasses can be arranged along the positioning rail to give them some support during the programme.
Loading the dishwasher Universal support (depending on model) This support is designed to hold tall glasses and glasses with stems securely. ^ Lower the support and lean tall glasses against it.
Loading the dishwasher Adjusting the upper basket Depending on the setting of the upper basket, the following plate dimensions In order to gain more space for taller can be accommodated. pieces of crockery in the bottom or upper basket, the upper basket can be Dishwasher with cutlery tray adjusted on three levels with 2 cm (see data plate for model number)
Loading the dishwasher Lower basket Hinged spikes ^ For larger and heavier items such as The spikes are used for washing plates plates, serving platters, saucepans, and saucers. bowls, etc. Small items such as saucers can also be placed in the lower basket. Do not place delicate glassware in the lower basket.
Loading the dishwasher Removable spiked insert Bottle holder (depending on model) You can remove the spiked insert to The bottle holder can be used to wash make more room for larger items of narrow items, e.g. milk and baby crockery, e.g. a large, flat pot, or bottles.
Loading the dishwasher Cutlery Cutlery tray (depending on model) If spoon handles do not fit between the holders, then lay them the other way round. ^ Arrange the cutlery in the tray as shown. To make unloading much easier, cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc.
Loading the dishwasher Cutlery basket (depending on model) ^ Fit it into the cutlery basket if required. ^ To avoid the risk of injury, knives and forks should be placed with the handles upwards in the basket. However, cutlery placed handle down in the basket will come out cleaner and drier.
Combi tabs are available as "3 in 1" or, Miele branded dishwasher cleaning when they also contain other components products are available from the Miele such as glass and stainless steel Spare Parts Department or via the protective additives and enhanced Internet at www.miele-shop.com.
Operation The flap is always open at the end of a Avoid inhalation of powder programme. detergents and do not ingest dishwasher detergent. Dishwasher detergents contain irritant or corrosive ingredients which can cause burning in the nose, mouth and throat if swallowed, or inhibit breathing.
Operation Switching on Starting a programme ^ Open the stopcock, if it is closed. ^ Select the programme required with the programme selector button. ^ Open the door. The indicator light next to the selected ^ Make sure the spray arms are not programme will come on.
Operation At the end of a programme Switching off ^ Open the door slightly to check that At the end of a programme: the programme has finished. ^ Open the door. The indicator light next to the ^ Switch the dishwasher off with the Off programme selected goes out when the button V.
Operation Interrupting a programme Changing a programme A programme is interrupted as soon as If the detergent dispenser flap has the door is opened. already opened, do not change the When the door is closed again, the programme. programme will continue from the point it was at before the door was opened.
Additional functions ^ Press the programme selector button Buzzer briefly four times. An audible tone sounds at the end of the programme or if there is a fault. The "Inlet/Drain" check light will flash briefly four times at intervals. You will hear the buzzer at the end of a programme in bursts of five with a short The upper right hand programme pause in between.
Additional functions Factory default setting The upper right hand indicator shows whether a setting other than the factory If you have altered any settings from default setting has been set. the factory default, you can re-set them back to the factory default settings as –...
Miele branded cleaning and drip onto the sides of the dishwasher conditioning products are available door. from the Miele Spare Parts These surfaces are outside the wash Department or via the internet at cabinet and are not accessed by www.miele-shop.com.
^ The control panel should only be powder cleaners and cream wiped with a damp cloth. cleaners. ^ Clean the front using a damp Miele – solvent-based cleaning agents, microfibre E-cloth or with a sponge – stainless steel cleaning agents, and a solution of hot water and washing-up liquid.
Cleaning and care Cleaning the filters in the wash cabinet The filter combination in the base of the wash cabinet retains coarse soil from the suds solution, preventing it accessing the circulation system and re-entering the cabinet through the spray arms. The dishwasher must not be used without all the filters in place.
Page 42
Cleaning and care ^ Replace the filter combination so that To clean the inside of the filter, the flap must be opened: it lies flat in the base of the wash cabinet. ^ Press catches a together in the ^ Then turn the handle clockwise, until direction of the arrows as shown, and open the filter b.
Cleaning and care ^ Remove the lower basket. Cleaning the spray arms Particles of food can get stuck in the spray arm jets and bearings. The spray arms should therefore be inspected and cleaned regularly (approx. every 4 - 6 months). ^ Switch the dishwasher off.
Problem solving guide With the aid of the following guide, faults in the performance of the appliance, some of which may result from incorrect operation can be put right without contacting the Service Department. Repairs should only be carried out by a suitably qualified and trained person in strict accordance with current local and national safety regulations.
Page 45
Problem solving guide Problem Possible cause Remedy The buzzer sounds. There may be a – Clean the water inlet filter All the programme technical fault. and clean the drain pump indicators flash when and non-return valve as the door is opened. described in "Maintenance".
Problem solving guide The dishwasher does not fill/drain. Problem Possible cause Remedy The dishwasher The stopcock is – Open the stopcock fully. stops working closed. shortly after the start of the programme. The buzzer sounds. The Inlet/Drain indicator flashes when the door is opened.
Problem solving guide General problems Problem Possible cause Remedy Detergent residue is The dispenser was still Make sure the dispenser is left in the dispenser at damp when detergent was dry before adding the end of a added. detergent. programme. The detergent Clogged detergent residue Clean the detergent from...
Problem solving guide Noises Problem Possible cause Remedy Knocking noise in the A spray arm is knocking Interrupt the programme, wash cabinet. against an item in a and rearrange the items basket. which are obstructing the spray arm. Items of crockery are Interrupt the programme, Rattling noise in the wash cabinet.
Problem solving guide Unsatisfactory washing result Problem Possible cause Remedy The dishes are not The dishes were not loaded See notes in "Loading the clean. correctly. dishwasher" The programme was not Select a more intensive powerful enough. programme. See Programme chart.
Page 50
Problem solving guide Problem Possible cause Remedy Dishes, cutlery The amount of rinse aid Replenish the reservoir, and glasses are may be insufficient, or the increase the dosage or not dry or are rinse aid reservoir empty. change the brand of rinse aid. flecked.
Page 51
Problem solving guide Problem Possible cause Remedy Glassware has a This may be caused by the Change your detergent. brown or blue tinge, detergent. and film cannot be wiped off. Glassware is dull and The glasses are not There is no remedy. discoloured;...
^ Replace the filter and seal, making union. This filter is available from the Miele Spares Parts dept. sure they are sitting correctly. ^ Reconnect the inlet hose to the Cleaning the filter:...
Maintenance Cleaning the drain pump and non-return valve If the water has not been pumped away at the end of a programme the drain pump or the non-return valve might be blocked. They are, however, easy to clean. ^ Disconnect the dishwasher from the mains supply.
Programme chart Crockery Food deposits Action required Mixed, All normal This needs an everyday crockery food deposits adaptable programme... Heat-sensitive glasses and plastic Fresh, This needs a short easily removed programme... food deposits Mixed crockery This needs a standard programme... Normal food deposits which have begun to dry To save water and...
Page 55
Programme chart Programme Detergent Compartment I Compartment II 25 ml Sensor wash 55-65° – 1 tab 25 ml Quick wash 40°C – 1 tab 25 ml Light soiling 50°C – 1 tab 25 ml Energy save – 1 tab 25 ml Pots &...
Page 56
Programme chart Programme Programme sequence Pre-wash Main wash Interim rinse Final rinse Drying °C °C Sensor wash Variable programme sequence, 55-65°C sensor controlled adjustment according to the amount of crockery and level of food deposits If required 55-65 If required Quick wash 40 °C Light soiling 50 °C Energy save...
Page 57
Programme chart Consumption Duration Energy Water Cold Litres Cold water water water water connection connection connection connection (15 °C) (55 °C) (15 °C) (55 °C) h:min h:min 1.30-1.60 0.75-1.00 13-22 1:45-2:30 1:35-2:16 0.70 0.22 0:38 0:30 1.25 0.90 1:32 1:20 1.05 0.70 2:54...
– Your Miele dealer, or technology. – the Miele Service Department (see Information regarding programme back cover for address). updates will be made known by the Miele Company as and when such Please note that telephone calls may developments become available.
Optional accessories To make the most of your dishwasher Optional accessories for particular purposes are available from your Miele dealer, the Spare Parts Department or online at www.miele-shop.com (some may be supplied as standard, depending on model). If you would like to …...
Electrical connection Electrical connection U.K. Non-rewireable plugs BS 1363 The fuse cover must be refitted when All electrical work must be changing the fuse, and if the fuse cover carried out by a suitably qualified is lost, the plug must not be used until a and competent person, in suitable replacement is obtained.
30 and 1000 kPa (0.3 and 10 bar). Providing your dishwasher has been If the water pressure is too high, a installed correctly, the Miele waterproof pressure reducer valve must be anti-leak system will protect you from fitted. water damage throughout its lifetime.
Plumbing Drainage Venting the drainage system – The appliance drainage system is If the on-site drain connection is fitted with a non-return valve, which situated lower than the guide path for prevents dirty water from flowing the bottom basket rollers in the open back into the dishwasher via the door, the drainage system must be drain hose.
Technical data Dishwasher model G 1XXX G 2XXX Height 80.5 cm 84.5 cm (adjustable + 6.5 cm) (adjustable + 6.5 cm) Height of building-in Min. 80.5 cm (+ 6.5 cm) Min. 84.5 cm (+ 6.5 cm) recess Width 59.8 cm 59.8 cm Width of building-in 60 cm...