COLOR MONITOR SERVICE MANUAL CHASSIS NO. : CL-42 FACTORY MODEL: LB700G MODEL: L1710S (LB700G-GU) L1710S (LB700G-GD) CAUTION BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
PRECAUTION WARNING FOR THE SAFETY-RELATED COMPONENT. WARNING BE CAREFUL ELECTRIC SHOCK ! • There are some special components used in LCD monitor that are important for safety. These parts are • If you want to replace with the new backlight (CCFL) or marked on the schematic diagram and the inverter circuit, must disconnect the AC adapter...
TIMING CHART VIDEO SYNC << Dot Clock (MHz), Horizontal Frequency (kHz), Vertical Frequency (Hz), Horizontal etc... (µs), Vertical etc... (ms) >> Total Period Video Active Time Front Porch Sync Duration Back Porch Sync Mode Resolution Frequency Clock Polarity Sort 31.469 640x350 25.175 70Hz...
OPERATING INSTRUCTIONS FRONT VIEW REAR VIEW D-Sub Signal Connect See Front Control Panel Power Connect Front Control Panel 1. Power ON/OFF Button 5. SELECT Button Use this button to turn the monitor on or off. Use this button to enter a selection in the On Screen Display. Use this button to scanning auto adjust.
LVDS R,G,B (Low Voltage differential Differential Signaling) AVDD2.5V AVDD3.3V Address DVDD2.5V DVDD3.3V AVDD 3.3V DVDD 3.3V Data 8 Bi t AVDD 2.5V DVDD 2.5V AC Inpu t R,G,B, H/V Sync...
DESCRIPTION OF BLOCK DIAGRAM 1. Video Controller Part & Display Data Transmitter Part. This part amplifies the level of video signal for the digital conversion and converts from the analog video signal to the digital video signal using a pixel clock. The pixel clock for each mode is generated by the PLL.
LIPS Board Block Diagram 50 ~ 60Hz 100KHz HVDC INPUT RECTIFIER ENERGY OUTPUT RECTIFIER COMPONENTS AND FILTER TRANSFER AND FILTER LINE 100 ~ 240V SIGNAL PHOTO- COLLENTI CONTROL COUPLER CIRCUIT ISOLATION PRIMARY SECONDARY High Voltage output INVERTER CIRCUIT Operation description_LIPS 1.
ADJUSTMENT All adjustment are thoroughly checked and corrected 2. Adjustment for White Balance when the monitor leaves the factory, but sometimes 1) Display Black pattern at SXGA/60Hz. several minor adjustment may be required. 2) Select COLOR BIAS CALIBRATION command Adjustment should be following procedure and after and Enter.
TROUBLESHOOTING GUIDE 1. NO POWER NO POWER (POWER INDICATOR OFF) CHECK J702 TROUBLE IN INPUT VOLTAGE LIPS (POWER) (12V) ? CHECK J702 TROUBLE IN 5V VOLTAGE LIPS (POWER) (5V) ? CHECK U203’s PIN 103. TROUBLE IN IS THIS PIN U203 or X201 OSCILLATED? TROUBLE SOMEWHERE ELSE...
Page 13
2. NO RASTER NO RASTER CHECK J702 PIN 5, 6 TROUBLE IN (5V) ? LIPS CHECK TROUBLE IN J705 PIN 1, 2, 3 U804 (5V) ? CHECK TROUBLE IN U801 U801 (3.3V)? CHECK TROUBLE IN U203(GM2121) ? U203 TROUBLE IN LCD MODULE...
Page 14
3. NO CLOCK (CLOCK GENERATOR) NO DOT CLOCK CHECK TROUBLE IN X201 20MHz ? X201 4. TROUBLE IN DPM TROUBLE IN DPM CHECK CHECK PC R713, R715 PC IS NOT GOING (SYNC) ? INTO DPM OFF MODE CHECK U203 PIN 102 TROUBLE IN WAVEFORM X201...
REPLACEMENT PARTS LIST CAUTION: BEFORE REPLACING ANY OF THESE COMPONENTS, READ CAREFULLY THE SAFETY PRECAUTIONS IN THIS MANUAL. * NOTE SAFETY Mark AL ALTERNATIVE PARTS DATE: 2002. 10. 16. DATE: 2002. 10. 16. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC.