Page 1
PLASMA TV OWNER’S MANUAL Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this infor- mation to your dealer when you require service.
13 amp BS 1362, BSI or ASTA approved type. Never use this plug with the fuse cover omitted. To obtain a replacement fuse cover contact your dealer or “LG Electronics U.K. Ltd.” If the type of plug supplied is not suitable for the mains sockets in your home, then the plug should be removed and a suitable type fitted.
Page 3
Safety Warnings Safety instructions have two kinds of information, and each meaning of it is as below. The violation of this instruction may cause serious injuries and even death. WARNING The violation of this instruction may cause light injuries or damage of the NOTES product.
4. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product. 4 PLASMA TV...
Introduction Introduction Introduction What is a Plasma Display ? If voltage is inputted to gas in glass panels, ultraviolet rays are outputted and fused with a fluorescent substance. At this moment, light is emitted. A Plasma Display is a next generation flat Display using this phenomenon. 160°...
Note : In teletext mode, the PIP PR +/-, VCR BUTTONS SWAP and PIP INPUT buttons are used for Controls a LG video cassette recorder. teletext function. Installing Batteries • Open the battery compartment cover on the back side and insert the batteries with correct polarity.
Introduction Location and Function of Controls Location and Function of Controls <Front Panel Controls> TV/AV MENU INPUT MENU 1. Power Button (Programme Up/Down) Switches the set on from standby or off to standby. Selects a programme or a menu item. Switches the set on from standby.
Page 8
9. AUDIO/VIDEO INPUT (AV5) these sockets. S-VIDEO/AUDIO IN SOCKETS S-VIDEO/AUDIO IN SOCKETS Connect the S-VIDEO out socket of an VCR to the S-VIDEO socket. Connect the audio out sockets of the VCR to the audio sock- ets as in AV4. 8 PLASMA TV...
Installation External Equipment V iewing Setups External Equipment V iewing Setups Antenna Connection - Be careful not to bend the bronze wire when connecting to an antenna port. Apartments (connecting to wall antenna socket) Antenna wall antenna socket < Back panel of the set > RF coaxial wire (75 ohms) VHF antenna UHF antenna...
Page 10
A A V1 Antenna COMPONENT COMPONENT AUDIO AUDIO A A V2 V VARIABLE ARIABLE AUDIO OUT AUDIO OUT VICE) A A V4 A A V3 (MONO) (MONO) S-VIDEO S-VIDEO VIDEO VIDEO AUDIO AUDIO Camcorder AUDIO VIDEO Video game set 10 PLASMA TV...
Page 11
Installation Watching DVD How to connect < Back panel of the set > Connect DVD video outputs to Y, P of COMPO- NENT INPUT and audio outputs to Audio sockets of VIDEO VIDEO AUDIO AUDIO AUDIO INPUT. A A V1 HDMI/ AUDIO AUDIO...
Page 12
RS-232C INPUT CONTROL (CONTROL/SERVICE) A A V4 4. Set the resolution output of the PC to SXGA or under A A V3 (MONO) (MONO) (1280 x 1024, 60Hz). (Refer to p. 13) S-VIDEO S-VIDEO VIDEO VIDEO AUDIO AUDIO 12 PLASMA TV...
- In this case, Audio use other cable. When PC (or sound card of PC) have Analog Audio Output Connector, RGB/DVI Audio Input of the set connect to Analog Audio Cable (not supplied with the product). And then you can listen to normal Audio. 14 PLASMA TV...
Installation Reference Cable sample HDMI Cable Analog Audio Cable (RCA type) (not supplied with the product) (not supplied with the product) Analog Audio Cable (Stereo to RCA type) HDMI to DVI Cable (not supplied with the product) (not supplied with the product) How to use 1.
Optional extras can be changed or modified for quality improvement. Without any notification new optional extras can be added. Contract your dealer for buying these items. Ceiling mounting bracket Tilt wall mounting bracket Video cables Audio cables 16 PLASMA TV...
Installation Installation Options Installation Options • The set can be installed in different ways such as on a wall, or on a desktop etc. • Install this set only in a location where adequate ventilation is available. Wall Mount: Horizontal Installation Desktop Pedestal Installation •...
3. Press the button and then use button to select your desired language. From this point on, the on-screen menus will be shown in the language of your choice. Press the EXIT button to return to normal TV viewing. 18 PLASMA TV...
Operation Channel Menu Options Channel Menu Options Auto Programme Tuning - All stations that can be received are stored by this method. It is recommended that you use auto programme during installation of this set. 1. Press the MENU button and then use button to select the STATION menu.
Band Favourite programme V/UHF SOUND 4. Press the OK button. Channel Fine TIME Press the EXIT button to return to normal TV viewing. Search SPECIAL Name SCREEN Booster F F G G PIP/DW Store 20 PLASMA TV...
Operation Programme Edit - This function enables you to delete or skip the stored programmes. Also you can move some stations to other pro- gramme numbers or copy a blank station data into the selected programme number. 1. Press the MENU button and then use button to select the STATION menu.
SCREEN PIP/DW Menu Prev. - You can enjoy the vivid and hi-definition picture with LG’s Excellent Digital Reality processor technology. - It’s not available to use this function in RGB[PC], HDMI[PC] mode. - When selecting picture options ( Intelligent Eye...
Operation sRGB - When the set was connected to external equipment with sRGB function, It’s adjusted a colour difference to display the equal image each other. - This function works in the following mode:RGB[PC], HDMI[PC]. 1. Press the MENU button and then use button to select the PICTURE menu.
F F / G G Bass TIME TV Speaker Press the EXIT button to return to normal TV viewing. SPECIAL SCREEN SRS TSXT . Note : Treble, Bass or BBE aren’t suitable to use PIP/DW Menu Prev. 24 PLASMA TV...
Operation TV Speaker - You can adjust internal speaker status. - In COMPONENT, RGB[PC] and HDMI[PC] mode, TV speaker/variable audio can be output even though there is no video signal. - If you want to use your external hi-fi stereo system, turn off the internal speakers of the set. 1.
To check the remaining sleep time, press the SLEEP button once. b. To cancel the sleep time, repeatedly press the SLEEP button until the display appears. --- Min c. If you turn the set off after setting the sleep timer, the setting will be erased. 26 PLASMA TV...
Operation Special Menu Options Special Menu Options Child Lock - The set can be set up so that it can only be used with the remote control. 1. Press the MENU button and then button to select the SPECIAL menu. STATION Language Child lock...
D D / E E PICTURE ISM Method Low power SOUND Set ID 3. Press the button to begin XD Demo Demo Demo To start TIME 4. To stop XD Demo , press the EXIT button. SPECIAL SCREEN PIP/DW Menu Prev. 28 PLASMA TV...
Operation Screen Menu Options Screen Menu Options Auto Configure - Automatically adjusts picture position and minimizes image shaking. - This function works in the following mode : RGB[PC]. 1. Press the MENU button and then use button to select the SCREEN menu. Auto config.
VGA Mode Zoom +/- SOUND Zoom +/- 3. Press the button and then button to make appropriate adjustments. Position TIME Cinema Press the EXIT button to return to normal TV viewing. SPECIAL Reset SCREEN PIP/DW Menu Prev. 30 PLASMA TV...
Operation Screen Position - You are available to this function after adjusting Zoom In/Out. 1. Press the MENU button and then button to select the SCREEN menu. STATION Auto config. Manual config. 2. Press the button and then button to select Position PICTURE VGA Mode...
Component 480p, 576p, 720p, 1080i for the sub picture, you Transparency can use Manual config to adjust the screen of the sub pic- ture. 3. Press the button and then button to adjust PIP trans- parency. Press the EXIT button to return to normal TV viewing. 32 PLASMA TV...
Operation eletext (option) eletext (option) - Teletext (or TOP text) is an optional function, therefore only the set with the teletext system can receive the teletext broadcast. - Teletext is a free service broadcast by most TV stations which gives up-to-the-minute information on news, weather, television programmes, share prices and many other topics.
In teletext mode, press this button to select a sub page number. The sub page number is displayed at the bottom of the screen. To hold or change the sub page, press the RED/ GREEN or PR buttons. Press this button again to exit this function. 34 PLASMA TV...
Miscellaneous External Control Device Setup External Control Device Setup - Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and control the set’s functions externally. How to connect external control equipment •...
Page 36
33. Input select (Main) Refer to p. 41 2: not support function 34. Input select (PIP) Refer to p. 41 3: Wait more time * When setting the 23 ~ 32, a menu doesn’t display on screen. 36 PLASMA TV...
Page 37
Miscellaneous 01. Power (Command 2 : a) 04. Screen Mute (Command 2 : d) G To control Power On/Off of the TV. G To select screen mute on/off. Transmission Transmission [k][d][ ][Set ID][ ][Data][Cr] [k][a][ ][Set ID][ ][Data][Cr] Data 0 : Screen mute off (Picture on) Data 0 : Power Off 1 : Power On 1 : Screen mute on (Picture off)
Page 38
* Refer to ‘Real data mapping 1’. See page 40. [m][ ][Set ID][ ][OK][Data][x] * If you’re not using the remote control, use this mode. [s][ ][Set ID][ ][OK][Data][x] When main power is on/off, external control lock is released. 38 PLASMA TV...
Page 39
Miscellaneous 18. Balance (Command 2 : t) 23. PIP Input Select (Command 2 : y) G To adjust balance. G To select input source for sub picture in PIP/DW pic- You can also adjust balance in the SOUND menu. ture mode. You can also adjust input source for sub picture using PIP INPUT button on remote control.
Page 40
SIZE on the remote control. C7 : Step 199 Transmission [j][t][ ][Set ID][ ][Data][Cr] FE : Step 254 FF : Step 255 Data Min: 0 ~ Max: 20 * Refer to ‘Real data mapping 1’. [t][ ][Set ID][ ][OK][Data][x] 40 PLASMA TV...
Page 41
Miscellaneous 32. Key 34. Input select (Command 1 : x, Command 2 : y) (Command 1 : m, Command 2 : c) G To adjust input source for sub picture in PIP mode G To send IR remote key code. Transmission Transmission [x][y][ ][Set ID][ ][Data][Cr]...
2.25 ms G Bit description • • Bit “0” Bit “1” 0.56 ms 0.56 ms 1.12 ms 2.24 ms G Frame interval : Tf The waveform is transmitted as long as a key is depressed. Tf=108ms @455KHz 42 PLASMA TV...
Page 43
Miscellaneous Code (Hexa) Function Note R/C Button R/C Button VOL+ R/C Button VOL- R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button (Power On/Off) POWER Discrete IR Code (Only Power On) POWER ON Discrete IR Code (Only Power Off) POWER OFF R/C Button MUTE...
If the device turned off, the programming is successful. 4. Press the MENU button to store the code. After blinking twice, this code is stored. 5. Test the remote functions to see if the device responds properly. If not, repeat from step 2. 44 PLASMA TV...
• A change in ambient humidity or temperature may result in an unusual noise Unusual sound from at the time of switching off or on of the set and does not indicate a fault with inside the set the set. 50 PLASMA TV...