xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch Hardware Installation Guide Intended Readers Typographical Conventions Notes, Notices, and Cautions Safety Instructions Safety Cautions General Precautions for Rack-Mountable Products Protecting Against Electrostatic Discharge The DES-3200 Series Hardware Installation Guide contains detailed information about the hardware specifications of a Switch in this series.
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch Hardware Installation Guide Safety Cautions To reduce the risk of bodily injury, electrical shock, fire, or damage to the equipment, observe the following precautions. Observe and follow service markings. Do not service any product except as explained in your system documentation. Opening or removing covers that are marked with the triangular symbol with a lightning bolt may expose you to electrical shock.
xStack® DES-3200 Series Layer 2 Managed Fast Ethernet Switch Hardware Installation Guide If the system has multiple sources of power, disconnect power from the system by unplugging all power cables from the power supplies. Move products with care; ensure that all casters and/or stabilizers are firmly connected to the system. Avoid sudden stops and uneven surfaces.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide 10/100/1000Mbps Copper / 100/1000Mbps SFP Ports, Two 10/100/1000Mbps Copper Ports, and One RJ-45 Console Port for out-of-band CLI configuration. DES-3200-28/ME Twenty-four 10/100Mbps Copper Ports, Two Combo 10/100/1000Mbps Copper / 100/1000Mbps SFP Ports, Two 100/1000Mbps SFP Ports, One RJ-45 Console Port for out-of-band CLI configuration, and One Alarm Connector Port.
Page 9
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Sixteen 10/100Mbps Copper Ports One Combo 10/100/1000Mbps Copper / 100/1000Mbps SFP port One 100/1000Mbps SFP Port One RJ-45 Console Port LEDs for Power, Console, Link/Act for port 1 to 16, and Link/Act/Speed for port 17 and 18 Figure 1-3.
Page 10
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Figure 1-6. Front Panel of the DES-3200-26-DC The front panel of the DES-3200-28 switch consists out of the following: Twenty-four 10/100Mbps Copper Ports Two Combo 10/100/1000Mbps Copper / 100/1000Mbps SFP ports ...
Page 11
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Figure 1-10. Front Panel of the DES-3200-28/ME The front panel of the DES-3200-52 switch consists out of the following: Forty-eight 10/100Mbps Copper Ports Two Combo 10/100/1000Mbps Copper / 100/1000Mbps SFP ports ...
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide LED Indicators The Switch supports LED indicators for Power, Console, Fan, and Link/Act or Link/Act/Speed for each port. The following shows the LED indicators for the DES-3200 Series along with an explanation of each indicator. Figure 1-14.
Page 13
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Figure 1-17. LED Indicators on DES-3200-18-DC Figure 1-18. LED Indicators on DES-3200-26 Figure 1-19 LED Indicators on DES-3200-26-DC Figure 1-20. LED Indicators on DES-3200-28...
Page 14
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Figure 1-21. LED Indicators on DES-3200-28F Figure 1-22. LED Indicators on DES-3200-28P Figure 1-23. LED Indicators on DES-3200-28/ME Figure 1-24. LED Indicators on DES-3200-52...
Page 15
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Figure 1-25. LED Indicators on DES-3200-52-DC Figure 1-26. LED Indicators on DES-3200-52P Location LED Indicative Color Status Description Solid Light Power on. Power Green Light off Power off. Solid Light Console on.
Page 16
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Solid Green When there is a secure 1000Mbps Ethernet connection (or link) at any of the ports. Blinking Green When there is reception or transmission (i.e. Activity—Act) of data occurring at a 1000Mbps Ethernet connected port.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Rear Panel Description The rear panel of the Switch contains an AC or DC power connector. The AC power connector is a standard three- pronged connector that supports the power cord. Plug-in the female connector of the provided power cord into this socket, and the male side of the cord into a power outlet.
Page 18
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Figure 1-33. Rear panel view of the DES-3200-28 Figure 1-34. Rear panel view of the DES-3200-28F Figure 1-35. Rear panel view of the DES-3200-28P Figure 1-36. Rear panel view of the DES-3200-28/ME Figure 1-37.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Side Panel Description The left- and right-hand panels of the Switch have heat vents to dissipate heat. Do not block these openings, and leave at least 6 inches of space at the rear and sides of the Switch for proper ventilation. Be reminded that without proper heat dissipation and air circulation, system components might overheat, which could lead to system failure Figure 1-40.
Page 20
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Figure 1-43. Side panels of the DES-3200-18-DC Figure 1-44. Side panels of the DES-3200-26 Figure 1-45. Side panels of the DES-3200-26-DC Figure 1-46. Side panels of the DES-3200-28...
Page 21
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Figure 1-47. Side panels of the DES-3200-28F Figure 1-48. Side panels of the DES-3200-28P Figure 1-49. Side panels of the DES-3200-28/ME Figure 1-50. Side panels of the DES-3200-52...
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Figure 1-51. Side panels of the DES-3200-52-DC Figure 1-52. Side panels of the DES-3200-52P Gigabit Combo Ports The DES-3200 Series features either two or four Gigabit Ethernet Combo ports. These ports are 1000BASE-T copper ports (optional) and Small Form Factor Portable (SFP) ports (optional).
Page 23
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Figure 1- 27. Installing the SFP Module The Switch is equipped with SFP ports, which are to be used with fiber-optical transceiver cabling in order to uplink various other networking devices for a gigabit link that may span great distances. For a full list of supported SFP transceivers, for this switch series, refer to the Appendix A.
Quick Installation Guide This manual on CD, including a D-View trial version If any item is missing or damaged, please contact your local D-Link Reseller for replacement. Before You Connect to the Network The site where you install the Switch may greatly affect its performance. Please follow these guidelines for setting up the Switch.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Installing the Switch without the Rack When installing the Switch on a desktop or shelf, the rubber feet included with the Switch should first be attached. Attach these cushioning feet on the bottom at each corner of the device. Allow enough ventilation space between the Switch and any other objects in the vicinity.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Mounting the Switch in a Standard 19" Rack CAUTION: Installing systems in a rack without the front and side stabilizers installed could cause the rack to tip over, potentially resulting in bodily injury under certain circumstances. Therefore, always install the stabilizers before installing components in the rack.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Figure 2-4. Close-up view of Power Receptacle 1. The DC power supply has a three-terminal wiring block consisting of a positive (+), a negative (-) and a safety ground terminal. 2.
Page 28
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Alarm Connector Port Contact Description Output. Normal Closed Pin. (42VAC or 60VDC) Output. Common Pin. (42VAC or 60VDC) Output. Normal Open Pin. (42VAC or 60VDC) Input 2. Input 2. Input 1.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Chapter 3 Connecting the Switch Switch to End Node Switch to Hub or Switch NOTE: All 10/100/1000Mbps NWay Ethernet ports can support both MDI-II and MDI-X connections. Switch to End Node End node is a generic name for edge networking devices that are connected to the Switch.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Switch to Hub or Switch These connections can be accomplished in a number of ways using a normal cable. A 10BASE-T hub or switch can be connected to the Switch via a twisted-pair Category 3, 4, 5 or 5e UTP/STP cable.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Chapter 4 Introduction to Switch Management Management Options Web-based Management Interface SNMP-Based Management Connecting the Console Port First Time Connecting to the Switch Password Protection SNMP Settings IP Address Assignment Management Options This system may be managed out-of-band through the console port on the front panel or in-band using Telnet.
DES-3200-28P Fast Ethernet Switch Command Line Interface Firmware: Build 4.04.003 Copyright(C) 2012 D-Link Corporation. All rights reserved. UserName: Figure 4-1. Initial screen after first connection First Time Connecting to the Switch The Switch supports user-based security that can allow you to prevent unauthorized users from accessing the Switch or changing its settings.
DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide DES-3200-28P Fast Ethernet Switch Command Line Interface Firmware: Build 4.04.003 Copyright(C) 2012 D-Link Corporation. All rights reserved. UserName: PassWord: DES-3200-28P:admin# Figure 4-2. Command Prompt NOTE: The first user automatically gets Administrator level privileges. It is recommended to create at least one Admin-level user account for the Switch.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide NOTICE: In case of lost passwords or password corruption, please refer to the section titled “Password Recovery Procedure” in Appendix B of the CLI Reference Guide” which will guide you through the steps necessary to resolve this issue.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide own proprietary enterprise MIB as an extended Management Information Base. Specifying the MIB Object Identifier may also retrieve the proprietary MIB. MIB values can be either read-only or read-write. IP Address Assignment Each Switch must be assigned its own IP Address, which is used for communication with an SNMP network manager or other TCP/IP application (for example BOOTP, TFTP).
Page 36
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Alternatively, you can enter config ipif System ipaddress xxx.xxx.xxx.xxx/z. Where the x's represent the IP address to be assigned to the IP interface named System and the z represents the corresponding number of subnets in CIDR notation.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Chapter 5 Web-based Switch Configuration Introduction Login to Web manager Web-Based User Interface Introduction All software functions of the Switch can be managed, configured and monitored via the embedded web-based (HTML) interface.
Function Area 1 Select the folder or window to be displayed. The folder icons can be opened to display the hyperlinked window buttons and subfolders contained within them. Click the D-Link logo to go to the D-Link website. Area 2 Presents a graphical near real-time image of the front panel of the Switch.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Web Pages When you connect to the management mode of the Switch with a Web browser, a login window is displayed. Enter a user name and password to access the Switch's management mode. When connecting to the management mode of the Switch with a web browser, a login screen is displayed.
Page 42
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide DES-3200-52: One fan DES-3200-52-DC: One fan DES-3200-52P: Four Fans The other switches in this series are Fanless. Operating Temperature -5 - 50°C Storage Temperature -40 - 70°C MTBF DES-3200-10: 738,787.9883 hours DES-3200-10-DC: 931,568.559 hours DES-3200-18: 670,243 hours DES-3200-18-DC: 825,160 hours...
Page 43
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Performance Transmission Method Store-and-forward Packet Buffer 1.5MB per device Packet Filtering/ 14,881 pps (10M port) Forwarding Rate 148,810 pps (100M port) 1,488,100 pps (1Gbps port) MAC Address Learning Automatic update. Supports 16K MAC address Priority Queues 8 Priority Queues per port Forwarding Table Age...
Page 44
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Blinking Amber When there is reception or transmission (i.e. Activity—Act) of data occurring at a 10/100Mbps Ethernet connected port. Light off No link. LED Per Solid Green Power feeding. 10/100Mbps Port in Green Blinking Green Error Condition...
Page 45
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide 100Mbps SFP Ports Compliant to the following standards: (DES-3200-28F Only) IEEE 802.3 compliance IEEE 802.3u compliance Support Full-Duplex operations IEEE 802.3x flow control support in full-duplex mode SFP (Mini GBIC) Support: DEM-210 (100BASE-FX, Single-mode, 15km) DEM-211 (100BASE-FX, Multi-mode, 2km) DEM-220T (TX-1550/RX-1310nm, Single-mode, 20km)
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Appendix B – Cables and Connectors Ethernet Cable When connecting the Switch to another switch, a bridge or hub, a normal cable is necessary. Please review these products for matching cable pin assignment. The following diagrams and tables show the standard RJ-45 receptacle/connector and their pin assignments.
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Console Cable When connecting the Switch a PC, a Console cable is necessary. The following diagrams and tables show the standard Console-to-DJ-45 receptacle/connector and their pin assignments. Figure B- 2. Console-to-RJ-45 Cable Console-RJ-45 Pin Assignments Console (DB9/RS232) RJ-45...
xStack® DES-3200 Series Layer 2 Ethernet Managed Switch Hardware Installation Guide Appendix C – Module Specs and Cable Lengths Use the following table to as a guide for the module specs and maximum cable lengths. Standard Media Type Maximum Distance 1000BASE-LX, Single-mode fiber module 10km 1000BASE-SX, Multi-mode fiber module...
The customer must submit with the product as part of the claim a written description of the Hardware defect or Software nonconformance in sufficient detail to allow D-Link to confirm the same, along with proof of purchase of the product (such as a copy of the dated purchase invoice for the product) if the product is not registered.
Page 50
D-Link Corporation/D-Link Systems, Inc., as stipulated by the United States Copyright Act of 1976 and any amendments thereto. Contents are subject to change without prior notice. Copyright 2004 by D-Link Corporation/D-Link Systems, Inc.
Product Registration Register your D-Link product online at http://support.dlink.com/register/ Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights.
You can find software updates and user documentation on the D- Link website. D-Link provides free technical support for customers within the United States and within Canada for the duration of the service period, and warranty confirmation service, during the warranty period on this product.
Page 53
Technical Support United Kingdom (Mon-Fri) Home Wireless/Broadband 0871 873 3000 (9.00am–06.00pm, Sat 10.00am-02.00pm) Managed, Smart, & Wireless Switches, or Firewalls 0871 873 0909 (09.00am – 05.30pm) (BT 10ppm, other carriers may vary.) Ireland (Mon-Fri) All Products 1890 886 899 (09.00am-06.00pm, Sat 10.00am-02.00pm) €0.05ppm peak, €0.045ppm off peak Times Internet http://dlink.com...
Assistance technique Assistance technique D-Link sur internet : http://dlink.com Assistance technique D-Link par téléphone : 01 76 54 84 17 Du lundi au vendredi de 9h à 19h (hors jours fériés) Asistencia Técnica Asistencia Técnica Telefónica de D-Link: +34 902 30 45 45 0,067 €/min...
Page 55
Pomoc techniczna Telefoniczna pomoc techniczna firmy D-Link: 0 801 022 021 Pomoc techniczna firmy D-Link świadczona przez Internet: http://dlink.com Technická podpora Web: http://dlink.com E-mail: support@dlink.cz Telefon ČR: +420 211 151 640 nebo SK: +421 (0)692 147 110 Telefonická podpora je v provozu: PO - PÁ od 09:00 do 17:00 Volání...
Page 56
Internetin kautta : http://dlink.com Arkisin klo. 09:00 - 18: 00 Numerosta : 0200-555 57 Teknisk Support D-Link Teknisk Support via Internet: http://dlink.com D-Link Teknisk Support via telefon: 0770-33 00 35 Vardagar 08:00 - 17:00 Assistência Técnica Assistência Técnica da D-Link na Internet: http://dlink.com e-mail: soporte@dlink.es...
Page 57
D-Link - ovo spletno stran www.dlink.eu http://dlink.com Suport tehnic Vă mulţumim pentru alegerea produselor D-Link. Pentru mai multe informaţii, suport şi manuale ale produselor vă rugăm să vizitaţi site-ul D-Link www.dlink.eu http://dlink.com...
Page 58
Technical Support You can find software updates and user documentation on the D-Link website. Tech Support for customers in Australia: D-Link Middle East - Dubai, U.A.E. Tel: 1300-766-868 Plot No. S31102, 24/7 Technical Support Jebel Ali Free Zone South, Web: http://www.dlink.com.au P.O.Box 18224, Dubai, U.A.E.
Page 59
Technical Support You can find software updates and user documentation on the D-Link website. Tech Support for customers in Iran Israel המגשימים רח Unit 5, 5th Floor, No. 20, 17th Alley , Bokharest ת " פ קרית מטלון St. , Argentine Sq. , 49348 .
Page 60
Техническая поддержка Обновления программного обеспечения и документация доступны на Интернет-сайте D-Link. D-Link предоставляет бесплатную поддержку для клиентов в течение гарантийного срока. Клиенты могут обратиться в группу технической поддержки D-Link по телефону или через Интернет. Техническая поддержка D-Link: 8-800-700-5465 Техническая поддержка через Интернет: http://www.dlink.ru...
Page 61
SOPORTE TÉCNICO Usted puede encontrar actualizaciones de softwares o firmwares y documentación para usuarios a través de nuestro sitio www.dlinkla.com SOPORTE TÉCNICO PARA USUARIOS EN LATINO AMERICA Soporte técnico a través de los siguientes teléfonos de D-Link PAIS NUMERO Argentina...
Page 62
Suporte Técnico Caso tenha dúvidas na instalação do produto, entre em contato com o Suporte Técnico D-Link. Acesse o site: www.dlink.com.br/suporte...
Page 64
Dukungan Teknis Update perangkat lunak dan dokumentasi pengguna dapat diperoleh pada situs web D-Link. Dukungan Teknis untuk pelanggan: Dukungan Teknis D-Link melalui telepon: Tel: +62-21-5731610 Dukungan Teknis D-Link melalui Internet: Email : support@dlink.co.id Website : http://support.dlink.co.id...
Page 65
Technical Support この度は弊社製品をお買い上げいただき、誠にありがとうご ざいます。 下記弊社 Web サイトからユーザ登録及び新製品登録を 行っていただき、ダウンロードサービスにて サポート情報、ファームウェア、ユーザマニュアルを ダウンロードすることができます。 ディーリンクジャパン Web サイト URL:http://www.dlink-jp.com...
8. What category best describes your company? Aerospace Engineering Education Finance Hospital Legal Insurance/Real Estate Manufacturing Retail/Chain store/Wholesale Government Transportation/Utilities/Communication System house/company Other________________________________ 9. Would you recommend your D-Link product to a friend? Don't know yet 10.Your comments on this product? __________________________________________________________________________________________ __________________________________________________________________________________________...