SAFETY PRECAUTIONS IMPORTANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards.
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this service unit under test. manual and its supplements and addenda, read and follow the 2. After removing an electrical assembly equipped with ES SAFETY PRECAUTIONS on page 3 of this publication. devices, place the assembly on a conductive surface such as NOTE: If unforeseen circumstances create conflict between the aluminum foil, to prevent electrostatic charge buildup or...
Page 5
IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through Circuit Board Foil Repair which the IC leads are inserted and then bent flat against the Excessive heat applied to the copper foil of any printed circuit circuit foil. When holes are the slotted type, the following technique board will weaken the adhesive that bonds the foil to the circuit should be used to remove and replace the IC.
37, 42 inch Wide Aspect Ratio 16:9 Tuning System LCD Module LC370WX3-SLD1 LG Philips LCD LC420WX6-SLD1 Operating Environment 1) Temp : 0 ~ 40 deg 2) Humidity : ~ 80 % Storage Environment 1) Temp. : -20 ~ 50 deg...
Page 7
5. Chroma & Brightness Item Unit Remark White brightness cd/m EZ Picture: Daylight, Color Temperature: Medium Color coordinate 0.602 0.632 0.662 Full Signal Swing (Default) 0.312 0.342 0.372 ± 0.025 GREEN 0.258 0.288 0.318 0.580 0.610 0.640 BLUE 0.117 0.147 0.177 0.035 0.065...
Page 10
11. Electro Optical Characteristic Specifications (module standard) 11-1. 37LC5DC Item Unit Remark Contrast Ratio(CR) Surface Luminance, White Cd/m Full white Luminance Variation ( white/5P) Response Time Gray to Gray msec Color coordinate 0.636 Full Pattern -0.03 0.343 +0.03 GREEN 0.284 0.615 BLUE 0.144...
Page 11
12. Customer Menu Setup (Shipment Condition) Item Condition Remark Input Mode TV02CH Volume Level Mute Aspect Ratio 16:9 Video EZ Picture Daylight Color temperature (Disable) Can be access only EZ picture is setting user mode Auto Advanced Cinema: Off Reset Audio Audio Language EZ SoundRite...
ADJUSTMENT INSTRUCTION 1. Application Range 4. Method of PTC MICOM Download This spec sheet is applied all of the 'LA64A' Chassis. 4.1 Connection of MICOM JIG 2. Specification 2.1 Because this is not a hot chassis, it is not necessary to use an isolation transformer.
Page 13
1) Select HCS12 Before ADC Calibration, should be executed the "Module type 2) Target Frequency Settings : selection". A. Checking the factor -> Use Specified Target Frequency , Unsecure target . B. Insert Target Bus Frequency -> 7372800 6. Color Balance adjustment. 3) Specify Algorithm: 9S12dt128_128k .12P 4) Specify S Record: select download file.
Page 14
6.2 Auto Component Color Balance 6.3 Auto RGB Color Balance 6.2.1 Required Test Equipment 6.3.1 Required Test Equipment - Remote controller for adjustment - Remote controller for adjustment - 802F Pattern Generator Which has 720p YPbPr output - 802F Pattern Generator, Master (MSPG-925FS), etc. with Standard (0.7Vpp) See Fig.
Page 15
7. EDID / DDC INPUT 6.4 RF Color Balance 1) Input the RF cable(2 ch) 7.1 EDID(The Extended Display Identification Data) / 2) Set the EZ Pictures to Daylight mode in Video menu. DDC(Display Data Channel) download 3) Press INSTART key on R/C for adjustment. 4) Press the (Vol.
Page 16
7.1.3 Data of EDID for 32/37/42LC5DC-UA,32LX5DC-UA Before adjustment of white balance, should be executed the 7.1.3.1 DDC data of Analog-RGB 'color balance adjustment' 8. Adjustment of White Balance 8.1 Required Equipment - Remote controller for adjustment - Color Analyzer (CA-210 or same product ) - Auto W/B adjustment instrument(only for Auto adjustment) - Use inner(SELF) Pattern 8.2 Adjustment of White Balance (For Manual adjustment)
Page 17
9. Auto white Balance (AV) 10.2 Lodgenet Card & Auto Camport Check command1 command2 Set ID Data Default value Input Select x R-Gain G-Gain B-Gain R-Offset G-Offset j B-Offset 10. Test factor for commercial model 10.1 IR In/ Out Check 10.3 RJP(Remote Jack Pack) Check 10.1.1 Check Order 'Pass' Judgment 10.3.1 Check Order 'Pass' Judgment...