LCD TV SERVICE MANUAL CHASSIS : LA51D FACTORY NAME : 42LC2D-UD MODEL : 42LC2D CAUTION BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
SAFETY PRECAUTIONS IMPORTANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards.
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this service unit under test. manual and its supplements and addenda, read and follow the 2. After removing an electrical assembly equipped with ES SAFETY PRECAUTIONS on page 3 of this publication. devices, place the assembly on a conductive surface such as NOTE: If unforeseen circumstances create conflict between the aluminum foil, to prevent electrostatic charge buildup or...
Page 5
IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through Circuit Board Foil Repair which the IC leads are inserted and then bent flat against the Excessive heat applied to the copper foil of any printed circuit circuit foil. When holes are the slotted type, the following technique board will weaken the adhesive that bonds the foil to the circuit should be used to remove and replace the IC.
Page 6
4) CATV : 01~135 5) CADTV : 01~135 Input Voltage 1) AC 100 ~ 240V 50/60Hz Market NORTH AMERICA Screen Size 42 inch Wide For 42LC2D Aspect Ratio 16:9 Tuning System LCD Module LC420W02-B6K1 For 42LC2D Operating Environment 1) Temp : 0 ~ 40 deg...
ADJUSTMENT INSTRUCTION 1. Application Object 4. EDID(The Extended Display These instructions are applied to all of the LCD TV, LA51D. Identification Data)/DDC (Display Data Channel) download 2. Notes This is the function that enables “Plug and Play". (1) Because this is not a hot chassis, it is not necessary to use 4-1.
Page 10
EDID DATA for RGB 5-3. Adjustment EDID table = (1) Select Component1 or Component2 as the input with 100% Horizontal Color Bar Pattern(HozTV31Bar) in 720p 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F Mode and select ‘Normal’...
Page 11
6-2. Adjustment of White Balance 7. Video(uPD) Operate the Zero-calibration of the CA-210, then attach 7-1. Required Equipment sensor to module surface when you adjust. Manual adjustment is also possible by the following sequence. MSPG925FA Pattern Generator-connector with Video Input 7-2.
Page 12
8. Shipping Conditions Item Condition Remark Input Mode TV02CH Volume Level Mute Aspect Ratio 16:9 Video EZ Picture Daylight Contrast Brightness Color Sharpness Tint Color-temperature Cool Audio Audio Language EZ SoundRite EZ Sound Normal Balance Treble Bass Front Surround TV Speaker Timer Auto clock Manual Clock...
SVC REMOCON To turn the TV on or off POWER To turn the TV on automatically if the power is supplied to the TV. (Use the POWER ON POWER key to deactivate): It should be deactivated when delivered. To activate the mute function. MUTE To check TV screen image easily.
TROUBLESHOOTING 1. Power Board 1-1. General Power Flow Start check Doesn't the It is identical Is the Interface screen whole come with Power Off signal operated? out? condition? 1. Check the Power Off 2. Check the Interface condition. signal condition. Doesn't the Doesn't the Doesn't the...
Page 15
2. No Power (1) Symptom Does’t minute discharge at module. Ø No front LED. Ø (2) Check follow Power cord connected? Plug in power cord. Cable connecting the Line Filter Connect Cable. and Power Board connected? Is Fuse(F101) on Power Board Replace Fuse.
3. Abnormal Display 3-1. Does’t display the OSD (1) Symptom LED is green Ø The minute discharge continuously becomes Ø accomplished from module (2) Check follow Check the LVDS Is the LVDS cable Replace cable. cable? connected well? Reset cable. Replace Is the VSC Digital Operates the Thine...
Page 17
3-2. In case of does’t display the screen into specific mode (1) Symptom The screen does not become the display from specific input mode Ø (RF, AV, Component, RGB, DVI). (2) Check follow Check the all input mode should become normality display. Ø...
Page 18
(5) Abnormal display in Component 480i mode Is the Video Decoder Are the Input voltage, IIC Replace IC IC306 UPD64011 Comm. and HV sync good? good? Is IC400 Are the Input voltage, IIC Replace IC Scaler good? Comm. and HV sync good? (6) Abnormal display in Component DTV mode Are the Input voltage, IIC Is normal the IC104...
Page 19
(7) Abnormal display in RGB DTV mode Are the Input voltage, IIC Is normal the IC101 Replace IC101 Comm. and HV sync good? CXA2181Q? Is normal the IC306 Are the Input voltage, IIC Replace IC306 MST9883C? Comm. and HV sync good? Is normal IC400 the Are the Input voltage, IIC Replace IC400...
4. No sound (1) Symptom LED is green Ø Screen display but no audio Ø (2) Check follow Check Speaker Is the SPK cable Replace SPK cable cable? connected well? Reset cable. Audio normal on Is the Flat cable IC1004 MSP4440K IC1002 NSP-2100A RGB/DVI? connected well?
REPLACEMENT PARTS LIST For Capacitor & Resistors, the CC, CX, CK, CN, CH : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit in the CQ : Polyestor RS : Metal Oxide Film P/No. means as follows; CE : Electrolytic RN : Metal Film CF : Fixed Film RH : CHIP, Metal Glazed(Chip)