HP designjet cc800ps Assembly Instructions Manual
Hide thumbs
Also See for designjet cc800ps:
- Color manual (61 pages) ,
- Reference manual (28 pages) ,
- Service manual (120 pages)
Advertisement
Quick Links
1 Plastic dust
cover
2 Scanner
3 Rear Table
4 Top bar
with guide
5 Leg (x2)
9 Cross bar
6 Maintenance
kit
7 Assembly
kit
8 Power
cables
Assembly poster
Your printer
should already be
assembled and working before starting this
procedure. For instructions on how to
assemble the printer, please refer to the
assembly poster included with the printer.
1
Attach the 2 feet
to the left and right
legs using 4
M6x30 screws (2
for each foot), tighten the screws with the Allen
key found in the assembly kit.
4
Attach the
bottom bar to
the leg using 2
M6X10 screws.
Assembly Instructions
hp designjet copier cc800ps
14 Front panel arm
12 Foot (x2) 13 Scanner
11 USB cables
10 Bottom bar
Read these instructions carefully...
and complete each stage before you start the
next.
What You Will Need to Do the Job
Because some of the components of the copier
are bulky, you will need 2 or 3 people to lift
them. See the descriptions that follow for
details, a symbol like this is used:
2
Secure the 2
legs by
fastening the cross
bar with 4 M6X10 screws (2 each side).
5
Attach the bottom bar to the other leg using 2
M6X10 screws.
18 System recovery
cd-rom
17 Media guides (x2)
Description
16 Front
panel
Screw M6X10 for base and top bar
15 Touch
screen
Screw M6X30 for base and top bar
stylus
Screw M4X25 for front panel arm
Allen Key 2,5mm for front panel
Screw M4X8 for front panel
maintenance
sheet
Slotted special screw for scanner
Allen Key 5mm for Top Bar
Allen Key front panel arm
3
Lay the 2 legs
down into the
position shown.
6
1
Assembly kit contents
A note about fixings:
When initially assembling the copier stand
do not fully tighten the screws; you will be
asked to do this later.
Raise the
legs carefully
into the
upright position.
Quantity
10
8
4
1
5
4
1
1
Advertisement
Related Manuals for HP designjet cc800ps
Summary of Contents for HP designjet cc800ps
- Page 1 Assembly Instructions hp designjet copier cc800ps 18 System recovery 1 Plastic dust cd-rom cover Assembly kit contents 17 Media guides (x2) 2 Scanner Description Quantity 16 Front panel 3 Rear Table Screw M6X10 for base and top bar 15 Touch...
- Page 2 M6X30 M6X10 Connect the rear table: this is fitted by locating the 4 guide pins on the rear of the Fasten the top bar and wire guide to the 2 legs table into the rubber framed holes on the top Remove the plastic safety tie and tighten up all using 4 M6X30 and 2 M6X10 screws.
- Page 3 Caution: see note after step 17 Dry the glass fully using a separate clean, dry Raise the two handles, and remove the Clean the glass with a lint-free cloth and a mild, lint-free cloth like the one provided with the pressure platen.
- Page 4 Connect the scanner's power cable to a If not done so already, connect the printer to a power outlet. power outlet and switch it on. Connect the other power cable to the scanner. Camera alignment & calibration... (Height alignment, stitching, basic calibration and color calibration) You are now required to calibrate the Slack...
- Page 5 For any further information on how to use The copier comes equipped with 2 The copier's measure can be changed your copier, see the online help system magnetic media guides: these can be between centimeters and inches by sliding available on your front panel using the button placed, and moved as required.
- Page 6 Not for resale ©2002 Hewlett-Packard Company All rights reserved Made in Europe Q1262-90011...