hit counter code
HP ProCurve Networking MSM320 Quick Start Manual
  1. Manuals
  2. Brands
  3. HP Manuals
  4. Wireless Access Point
  5. MSM320
  6. Quick start manual

HP ProCurve Networking MSM320 Quick Start Manual

Hide thumbs Also See for ProCurve Networking MSM320:
1
2
3
4
5
6

Advertisement

Table of Contents

The MSM320 is a Wi-Fi Alliance authorized Wi-Fi CERTIFIED 802.11a/b/g product. The
Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi Alliance. The MSM320 is
certified under the SpectraLink Voice Interoperability for Enterprise Wireless (VIEW)
Certification Program when it operates in autonomous mode or in controlled mode in
VIEW
conjunction with an MSM7xx Controller.
Certified
This Quickstart shows you how to get started using the MSM320 Access Point (US J9360A/B, WW J9364A/B). This Quickstart also applies to the MSM325
(US J9369A/B, WW J9373A/B) Access Point with integrated sensor.
After reading this Quickstart, you can visit www.hp.com/go/procurve/manuals and download documents of particular interest such as the MSM3xx / MSM4xx
Access Points Management and Configuration Guide and the MSM7xx Controllers Management and Configuration Guide. For information on the Integrated
Sensor, see the RF Manager documentation.
Hardware overview
Package contents
MSM320, documentation, four 2.4-GHz (2-dBi) / 5-GHz (2-dBi) dual-mode omnidirectional
antennas.
Reset button
Press and quickly release the button to reset the MSM320. To reset to factory default
settings, press and hold the reset button until the status lights flash three times, then
release. For details, see Resetting to factory defaults in the MSM3xx / MSM4xx Access
Points Management and Configuration Guide.
To reconnect to the management tool after a factory reset, your computer must be
Note:
connected to Ethernet Port 1.
MSM320 Access Point Quickstart
In
Radios and antennas
The MSM320 has two radios, each with two antennas for diversity.
The antenna connectors are reverse-polarity SMA jacks. Antennas or cable connectors must
use RP-SMA plugs. Antennas can be mounted directly on the MSM320. When a single
antenna is used, it is recommended to connect it to the Main antenna connector.
Optional external antennas are available from HP ProCurve. On the HP ProCurve Website, see
the Accessories section for the MSM320.
Ethernet ports
The MSM320 has two 10/100 Mbps Ethernet ports with RJ-45 connectors. Port 1 supports
Power over Ethernet (PoE) 802.3af. In controlled mode, Port 1 should be used. In
autonomous mode, Port 1 or Port 2 can be used.

Advertisement

Table of Contents
loading

Related Manuals for HP ProCurve Networking MSM320

Summary of Contents for HP ProCurve Networking MSM320

  • Page 1 (US J9369A/B, WW J9373A/B) Access Point with integrated sensor. After reading this Quickstart, you can visit www.hp.com/go/procurve/manuals and download documents of particular interest such as the MSM3xx / MSM4xx Access Points Management and Configuration Guide and the MSM7xx Controllers Management and Configuration Guide. For information on the Integrated Sensor, see the RF Manager documentation.

  • Page 2: About Controlled Mode And Autonomous Mode

    Failure to do so may result in personal injury, fire, equipment damage, or a voided warranty. The HP ProCurve hardware warranty provides no Power light is on. Radio and Ethernet lights The MSM320 has found a controller and is protection against damage caused by static discharge or a lightning strike.

  • Page 3: Installation

    • If using a PoE switch or injector, power it on. • A PoE-enabled switch. Various PoE-enabled switches are available from HP ProCurve. • If using a power supply, connect it to the MSM320 then power on the supply. •...

  • Page 4: Test The Wireless Network

    MSM320 Access Point Quickstart HP ProCurve Networking to the management tool. The security warning will not appear again unless you change • Let the DHCP server automatically assign an IP address. By default, the DHCP server the IP address of the MSM320.

  • Page 5: Performing Additional Configuration

    For example, in Windows Vista from the Start menu, select Connect to, and then HP ProCurve from the list of available wireless networks. You may have to wait a short time for this wireless network name to appear in the wireless networks list.
  • Page 6 MSM320 Access Point Quickstart HP ProCurve Networking February 2010 © Copyright 2010 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. Printed in Document part # 5998-0472 *5998-0472*...

Table of Contents