Advertisement
Please read this manual carefully before operating your set and retain it for future reference.
Manual for:
GM-C372SQCN, GM-F372SQCN, LT29BPP, LT29BPPK, LT29BPPX, LT29BPW, LT29WPP, LT29WPPX, LT32BPP, LT32BPPK, LT32BPPX, LT32BPW, LT32WPP, LT32WPPX, LT32WPW, GT26BPG, GM-B242SQCB, GT32WPK, GT32WDC, GT32BDC, GT29WDC, GT29BDC, GT29BPK
Internet: www.lg.com
THIS MANUAL CONTAINS SEVERAL IMPORTANT SAFETY NOTICES. ALWAYS READ AND OBEY ALL OF THE FOLLOWING SAFETY MESSAGES.
If you fail to follow these instructions you will be killed or seriously injured.
Misuses of the product will cause you physical damage or personal wounds.
Inadequate use and installation will cause damage to your property.
All safety labels will inform you of potential danger, ways to reduce chance of injury and what can happen if instructions are not followed.
WARNINGS AND IMPORTANT SAFETY MEASURES
Read all instructions before use your product.
This appliance contains a small amount of isobutane refrigerant (R600a), natural gas with high environmental compatibility, but it is also combustible. When transporting and installing the appliance, care should be taken to ensure that any part of the refrigerating circuit is damaged. Refrigerant squirting out of the pipes could ignite or cause an eye injury. If a leak is detected, avoid any naked flames or potential sources of ignition and air the room in which the appliance is placed for several minutes. In order to avoid the creation of a flammable gas air mixture if a leak in the refrigerating circuit occurs, the size of the room in which the appliance may be placed depends on the amount of refrigerant used. The room must be 1m² in size for every 8 grams of R600a refrigerant inside the appliance. The amount of refrigerant in your particular appliance is shown on the identification label inside the appliance. Never start up an appliance showing any signs of damage. If in doubt, consult your service center.
Risk of Fire, keep in mind next caution points when you move or install your refrigerator, gas used in your appliance is inflammable:
Risk of Fire or Explosion (Inflammable Refrigerant), the refrigerator only must be repaired by qualified personal. Do not drill refrigeration circuit. Read instructions in your Owner's Manual before use this product, all safety messages must be followed.
This appliance is not intended for being used by children, persons with physical or mental disabilities, persons with reduced sensory or mental capacity, or persons with lack of experience or know-how, unless they have supervision or instruction in relation to the use of the appliance by the person responsible for their safety. Children should be supervised to assure that they do not play with the appliance.
NEVER USE EXTENSION CORDS AND POWER STRIPS: Your refrigerator must be installed near from outlet to avoid extension cords and never connect multiple machines in the same socket, this can cause wiring to overcharge, warming, voltage variation and bad functioning. Do not use extension cords or ungrounded (two prong) adapters.
ELECTRICAL CORD REPLACEMENT: If electrical cord gets damaged it must be replaced by the manufacturer, our service center or qualified LG Electronics personnel to minimize risks.
Remove water or dust from the power plug and insert it with the ends of the pins securely connected. Dust, water or unstable connection may fire or electric shock.
GROUND CONNECTION: In case of electrical surge, connection to ground will reduce risks of electric shock hazard. This unit must be grounded. Consult a qualified electrician. When moving your refrigerator, be careful not to step on the electrical cord with the machine's rollers.
NEVER KEEP EXPLOSIVES INSIDE!!! : Never store explosive substances or chemicals in your refrigerator such as benzene, alcohol, etc. It is DANGEROUS
DANGEROUS FUN: An empty refrigerator can be very dangerous for children. Remove doors or magnetic packaging when not be in use or secure it in a way to make it impossible to open and allow a child to go in as this can lead to suffocation. Never allow a child to climb, hang or play with the refrigerator compartments. They can get hurt themselves and damage the refrigerator.
PLUG ACCESS: The refrigerator- freezer must be placed in a way that the electrical cord can be pulled easily in case of emergency.
WHAT TO DO WITH YOUR OLD REFRIGERATOR: Your refrigerator contains liquids (refrigerant, lubricant) made of recyclable materials. All these materials must be sent to a recycling waste disposal site as they can be reused after a specific recycling process. Contact local authorities.
Please do not catch the side of the door when opening the door. When open/ close the door, please use handle. There is a possibility that the hand is caught on the door and injured.
DO NOT STORE ANIMALS: Do not store any living animal in your refrigerator.
Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.
The maintenance of the lowest area from the refrigerator's back side (see image) only must be done by qualified personal, do it by non qualified technician can produce risk of electric shock.
Do not place heavy or dangerous objects (vessel with liquid or medicines, etc.) on the top of the refrigerator, as this may cause physical damage to you or the refrigerator.
Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.
Do not damage the refrigerant circuit.
Do not use the refrigerator in horizontal position.
Do not put fingers in "pinch point" areas (like clearances between doors & cabinets) when the door is opened or closed. Make sure your hands and feet do not get stuck when opening and closing the appliance door.
This appliance is intended to be used in household and similar applications such as: staff ktichen areas in shops, offices and other working environments; farm houses and by clients in hotels, motels and other resi- dential type environments; bed and breakfast type environments; catering and similar non-retail applications.
Before installing your refrigerator, remove any tape or temporary stickers. Do not remove any stickers that feature warnings, the model serial number or the technical label of the product located on the back of the refrigerator. To remove adhesive tape residue, rub it well with your fingers and a little liquid detergent. Clean with warm water and let dry. Do not use sharp instruments, rubbing alcohol, flammable liquids or abrasive cleaning products to remove the adhesive tape or glue. These products can damage the surface of your refrigerator. The shelves come already installed in their factory position. Remove the shelves and replace them according to your spacing needs.
In places with high temperatures, freezing capacity can be affected and cause high consumption of electrical energy. Never install in places with high humidity as this can cause oxidation and electric shock hazard.
Your refrigerator must be leveled and placed on a strong floor. An unstable installation can produce noise and vibrations. If the floor is uneven, level the unit by twisting the height adjusting screw, this will eliminate unwanted sounds and vibrations.
NOTE: For adjusting leveling screws lift the front of the refrigerator and insert a screwdriver in the holes located in the leveling screws, then turn them clockwise ( ) to raise your refrigerator and counter-clockwise () to lower it.
The refrigerator will work efficiently if room temperature is between 10°C and 43°C (50°F and 109,4°F). This refrigerator is not for outdoor installation.
Adequate air flow is needed for an efficient operation. Keep your refrigerator at a relative distance from other objects. Reduced distances between the unit and other nearby objects can diminish freezing capacity and rise consumption of electrical energy.
NOTE: Be careful when you open the doors, one of them can be open more than the other one. Avoid hit the doors with items around the refrigerator area.
The room must be 1m² in size for every 8 grams of R600a refrigerant inside the appliance.
The amount of refrigerant in your particular appliance is shown on the identification label inside the appliance.
WARNING. EXCESSIVE WEIGHT HAZARD. Use the assistance of two or more persons to move or install the refrigerator. Not following these instructions may cause injury to the back and other parts of the body.
Wait at least one hour before connecting, after installation was completed.
FOR YOUR PERSONAL SAFETY, this device must be properly grounded.
Connect to a single undamaged socket. Not having proper installation will require you to call qualified personnel to achieve it.
Do not, under any circumstance, cut or extract the third prong from the plug. It is your responsibility and obligation to replace two-prong outlets with that of an adequately grounded three-prong outlet.
REPLACING ELECTRICAL CORD, if the electrical cord is damaged, it must be replaced by our service center or qualified LG technician to avoid any risk. NEVER disconnect the refrigerator by pulling the electrical cord, always grip the plug firmly and disconnect it directly from the outlet.
Leave your refrigerator working from 2 h to 3 h before storing food. If operation is interrupted wait 5 minutes before trying again.
If you wish to dispose of your refrigerator, keep in mind the following Warning.
If the use of this unit is no longer needed, please contact local authorities to dispose of this product in a safe way due contains Cyclopentane or pentane as gas for insulation and R600a as refrigerant. Insulation gases and refrigerant require a special elimination process. This product contains flammable insulation and refrigerant.
NOTE: This guide covers different models. Your refrigerator could have some or all of the features and parts listed below. The location of some of the parts may not correspond with your model.
Water Dispenser in the front of Refrigerator Door
Ice Maker (Twist'n serve)
Ice Tray
Remember that your refrigerator must be grounded.
If operation is interrupted, wait 5 minutes before restarting it.
(on some models) Ice Maker "Twist'n Serve"
Thawing occurs automatically, you do not need to worry about this. Thawed water will flow into the evaporation shelf
Control types for adjusting cooling.
NOTE: Be careful of not blocking or moving with food packages the temperature controls, you might change or not recognize the temperature in which your refrigerator is set.
Control of: | What does it control? | How it can be adjusted? | ||||
Freezer | Controls the flow of cold air that goes from the freezer into the refrigerator. | Change the control by sliding it softly, the arrow shows the temperature selected for your freezer compartment (see table below as reference). | ||||
Refrigerator | Controls the temperature of the refrigerator. | Turn the knob until indicates the desired temperature (see table below as reference). | ||||
Recommended Temperature Settings | ||||||
Control of: | SUMMER (Hot, more of 28°C) | SPRING (Warm, 17-28°C) | AUTUMN (Fresh, 12-17°C) | WINTER (Cold, 5-12°C) | ||
Freezer | Set in 1 | Set in 2 | Set in 3 | Set in 3 | ||
Refrigerator | Set in 7 | Set in 6 | Set in 5 | Set in 4 |
NOTE: Setting the Freezer dial at (4~5) will maintain a low temperature in the freezer. But the Refrigerator's cooling speed will be reduced. When set to (4~5) during hotter climates, it may also be necessary to adjust the refrigerator compartment temperature to a cooler temperature (6~7).
Knob is for quick freezing in the freezer compartment. The refrigerator can be operated continuously or the refrigerator compartment can be warmer. When the quick freezing is finished, please return to set the Knob at Normal.
NOTE: For an optimal performance of your refrigerator, it is necessary adjust the control in the settings recommended by the manufacturer.
The shelves of your refrigerator can be adjusted to comply with your storage needs; depending on the model you have it can include glass shelves or plastic shelves. Storing your foods together and adjusting the shelves to different heights will help you to locate what you need in an easier way. This also helps your refrigerator to stay shut longer which will save you energy.
While your refrigerator glass shelves are cold do not clean with hot or warm water. The glass shelves may break if they're exposed to rapid temperature changes or hard impacts. For your safety the glass shelves are made out of tempered glass so when at breaking they will fracture into tiny fragments. NOTE: Be careful while moving or relocating the shelves, they are heavy. If moving the shelves is required keep in mind to locate them in a safe environment to prevent them from breaking (the tempered glass on the front side of the appliance door or the shelves can be damaged by an impact. If it is broken, do not touch it with wet hands, as this may result in injury).
Refrigerator Shelf
In order to remove the refrigerator shelves follow these instructions:
NOTE: Be careful when you remove the shelves from the refrigerator, because they are secured to the refrigerator walls.
Do not insert the shelves upside down. The shelves may fall, causing injury.
The door baskets are removable for easy cleaning and adjustment.
NOTE: Empty the food charge before you move the door basket.
Someone could get hurt if the baskets are not well assembled.
Do not hang from the appliance door, storage room or shelf. It may make the refrigerator fallen down or damage the hands. Especially, do not allow the children to do the above.
DO NOT allow children play with baskets. Sharp corners on basket could cause injury.
The magic crisper provides fresher tasting fruit and vegetables by letting you easily control humidity.
High: lets moist air out of the crisper for best storage of fruit.
Low: keeps moist air in the crisper for best storage of fresh, leafy vegetables.
To remove vegetable drawer, follow these instructions:
Your refrigerator has a system that allows you having cold water without opening refrigerator door. For dispensing water, push backward the dispenser lever with a glass until the water flows.
NOTE: After using your dispenser, it is normal if some drops fall, you can reduce this by removing slowly the glass from the lever.
For cleaning the water tank of your dispenser, follow the next steps:
For installing the tank in its original position (in refrigerator's door), follow the next instructions:
For supply the tank with water, follow the instructions below:
NOTE: Do not fill the tank completely in order to avoid water spills, the maximum capacity it is indicated in your water tank.
Fill only with potable water. Using other beverages (as beer, soda or liquids with sugar) may damage the dispensing system.
If you need to empty the water tank, follow the next steps:
The Door Alarm function is designed to prevent refrigerator malfunctioning that could occur if refrigerator door remains open. If refrigerator door is left open for more than 1 minute, a warning alarm sounds at 30 second intervals.
NOTE: This function can not be deactivated.
LG ThinQ Application
This feature is only available on models with the or logo.
The LG ThinQ application allows you to communicate with the appliance using a smartphone.
LG ThinQ Application Features
Communicate with the appliance from a smartphone using the convenient smart features.
SMART DIAGNOSIS
If you experience a problem while using the appliance, this smart diagnosis feature will help you diagnose the problem.
NOTE:
Installing the LG ThinQ Application
Search for the LG ThinQ application from the Google Play Store or Apple App Store on a smart phone.
Smart Diagnosis
This feature is only available on models with the or logo.
Use this feature to help you diagnose and solve problems with your appliance.
NOTE:
Using Audible Diagnosis to Diagnose Issues
Follow the instructions below to use the audible diagnosis method.
NOTE:
In order to avoid bad or unwanted odors, is important to keep the refrigerator clean. Any spilled food must be cleaned immediately; they can stain and/ or acidify the plastic parts of the refrigerator if they are let to get dry.
Exterior: Use a warm mixture of mild detergent or soap to clean the refrigerator's surface. Clean with a damp cloth and dry immediately.
Do not clean power cord using wet cloth, as this may cause an electric shock.
Interior: It is recommended to clean the interior often. Wash all the baskets and drawers with a mixture of bicarbonate or mild detergent with water. Clean and dry. Using other kinds of products might damage your refrigerator.
After Cleaning: Check that the electrical cord is not damaged or overheated and it is properly plugged.
Door lining and gaskets: For plastic parts do not use cleaners, hard detergents, bleach or cleaners with petroleum.
Plastic Parts: Do not use paper towels, abrasive cleaners or flammable products, these could damage or scratch the product.
Back Cover: In order to get an efficient performance of your refrigerator, clean its back cover at least twice a year.
Verify that electrical cord is not damaged and the plug is not overheated and it's connected in outlet in a proper way.
The refrigerator does not work. |
|
There is a power interruption. | In case of a black out, call your electric company and ask how long it will last.
|
The temperature of the refrigerator or the freezer is too warm or hot. |
|
I can hear some weird or abnormal sounds. |
|
There are some odors in the refrigerator. |
|
Some humidity is formed in the cabinet's surface. |
|
The front part of the refrigerator is getting warm. |
|
The compressor works too frequently and for extended periods of time. |
|
REMEMBER: In a power failure, a full freezer stays cold longer than a partially filled one. A freezer full of meat stays cold longer than a freezer full of baked goods.
THE OVERALL PERFORMANCE OR EFFICIENCY OF YOUR REFRIGERATOR MAY BE AFFECTED IF:
DURING VACATIONS WE RECOMMEND YOU THE FOLLOWING:
IF YOU ARE PLANNING TO MOVE OR TO CHANGE YOUR REFRIGERATOR FROM ITS CURRENT POSITION:
Your refrigerator has a LED lamp for changing it you must call Service Center to perform the replacement by qualified technician.
In case of replacement, the new lamp must have the same specification than the original one.
The front wall of the cabinet of the refrigerator might warm up sometimes specially during installation. DO NOT ALARM! It's normal due to avoid humidity or "sweat".
(some models)
DO NOT ALARM! The warming up is normal because in both sides the refrigeration pipes are located.
In case of your refrigerator was damaged for some flood, do not use it until qualified technician confirms its performance.
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download LG GT32WPK, GT32WDC, GT29WDC, LT32BPP - Top Mount Refrigerator Manual
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the GT32WDC that isn't answered in the manual? Leave your question here.